mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
85 lines
3.0 KiB
Markdown
85 lines
3.0 KiB
Markdown
# MCU-Link Debug Probe
|
|
|
|
The [MCU-Link Debug Probe](https://www.nxp.com/design/design-center/software/development-software/mcuxpresso-software-and-tools-/mcu-link-debug-probe:MCU-LINK) is a cheap, fast and highly capable debug probe that can serve as a stand-alone debug and console communicator when working with Pixhawk boards.
|
|
|
|
주요 기능:
|
|
|
|
- Just one single USB-C connection for Reset, SWD, SWO, and serial in a very small package!
|
|
- Up to 9.6MBit/s SWO connection.
|
|
Up to 5 MBaud serial. 1.2V to 5V target voltage.
|
|
USB2 high-speed 480 Mbps connection.
|
|
- Driven by NXP LinkServer or pyOCD software with wide device support.
|
|
- Much cheaper (<15€) than a Pixhawk Debug Adapter (~20€) with a JLink EDU mini (~55€) or JLink BASE (~400€) while having better hardware specs.
|
|
|
|
The [Pixhawk Debug Adapter](https://holybro.com/products/pixhawk-debug-adapter) provides an easy way to connect a Pixhawk to an MCU-Link (the probe does not come with an adapter for working with Pixhawk flight controllers).
|
|
|
|
:::info
|
|
These instructions have been tested on: FMUv6X-RT, FMUv6X, FMUv6c, FMUv5X.
|
|
:::
|
|
|
|
## Debugging Configuration using NXP LinkServer
|
|
|
|
The MCU-Link provides for NXP (FMUv6X-RT) chips the [LinkServer](https://www.nxp.com/design/design-center/software/development-software/mcuxpresso-software-and-tools-/linkserver-for-microcontrollers:LINKERSERVER) GDB server:
|
|
|
|
[Download](https://www.nxp.com/design/design-center/software/development-software/mcuxpresso-software-and-tools-/linkserver-for-microcontrollers:LINKERSERVER#downloads) the Linkserver for your operating system and follow the installation instructions.
|
|
|
|
On Windows LinkServer gets installed to `C:\NXP\LinkServer_x.x.x`
|
|
On Linux LinkServer gets installed `/usr/local/LinkServer/LinkServer`
|
|
|
|
To flash you can use the `LinkServer flash` command with target `MIMXRT1176xxxxx:MIMXRT1170-EVK-CM7-ONLY` for the FMUv6X-RT
|
|
|
|
```sh
|
|
/usr/local/LinkServer/LinkServer flash MIMXRT1176xxxxx:MIMXRT1170-EVK-CM7-ONLY load build/px4_fmu-v6xrt_default/px4_fmu-v6xrt_default.elf
|
|
```
|
|
|
|
You can launch the GDB server in a new terminal shell:
|
|
|
|
```sh
|
|
/usr/local/LinkServer/LinkServer gdbserver MIMXRT1176xxxxx:MIMXRT1170-EVK-CM7-ONLY
|
|
```
|
|
|
|
Then connect to port 3333 via GDB:
|
|
|
|
```sh
|
|
arm-none-eabi-gdb build/px4_fmu-v6xrt_default/px4_fmu-v6xrt_default.elf -ex "target extended-remote :3333"
|
|
```
|
|
|
|
Use GDB to load the binary into the Pixhawk:
|
|
|
|
```sh
|
|
(gdb) load
|
|
```
|
|
|
|
## Debugging Configuration using pyOCD
|
|
|
|
The MCU-Link provides the [GDB server via pyOCD](https://pyocd.io/):
|
|
|
|
```sh
|
|
python3 -m pip install -U pyocd
|
|
```
|
|
|
|
You can launch the GDB server in a new terminal shell:
|
|
|
|
```sh
|
|
pyocd gdb -t mimxrt1170_cm7
|
|
```
|
|
|
|
The target needs to be one of:
|
|
|
|
- FMUv6X-RT: `mimxrt1170_cm7`
|
|
- FMUv6X: `stm32h743xx`
|
|
- FMUv6C: `stm32h743xx`
|
|
- FMUv5X: `stm32f767zi`
|
|
|
|
You can then connect to port 3333 via GDB:
|
|
|
|
```sh
|
|
arm-none-eabi-gdb build/px4_fmu-v6xrt_default/px4_fmu-v6xrt_default.elf -ex "target extended-remote :3333"
|
|
```
|
|
|
|
Use GDB to load the binary into the Pixhawk:
|
|
|
|
```sh
|
|
(gdb) load
|
|
```
|