mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
179 lines
6.0 KiB
Markdown
179 lines
6.0 KiB
Markdown
# CUAV X25-SUPER
|
|
|
|
<Badge type="tip" text="PX4 v1.18" />
|
|
|
|
::: warning
|
|
PX4 does not manufacture this (or any) autopilot.
|
|
Contact the [manufacturer](https://store.cuav.net/) for hardware support or compliance issues.
|
|
:::
|
|
|
|
The _X25-SUPER_ is an advanced autopilot manufactured by CUAV<sup>®</sup>.
|
|
|
|
The autopilot is recommended for commercial system integration but is also suitable for academic research and any other applications.
|
|
|
|
|
|
|
|
The X25-SUPER brings you ultimate performance, stability, and reliability in every aspect.
|
|
|
|
::: info
|
|
These flight controllers are [manufacturer supported](../flight_controller/autopilot_manufacturer_supported.md).
|
|
:::
|
|
|
|
### Features
|
|
|
|
- Arm® Cortex-M7® processor (STM32H743XI) with Floating-Point Unit (FPU), operating at 480MHz, and featuring 2MB Flash memory.
|
|
Enables developers to enhance productivity and efficiency, allowing for more complex algorithms and models.
|
|
- Automotive-grade RM3100 compass.
|
|
Designed for better stability and anti-interference capability.
|
|
- Triple-redundant IMUs and dual-redundant barometers located on separate buses.
|
|
If the PX4 autopilot detects a sensor failure, the system seamlessly switches to another sensor to maintain flight control reliability.
|
|
- Independent LDO power control supplies power to each sensor group.
|
|
A vibration isolation system filters high-frequency vibrations and reduces noise to ensure accurate readings, enabling better overall flight performance for the vehicle.
|
|
- Integrated Microchip Ethernet PHY for high-speed communication with onboard devices like mission computers via Ethernet.
|
|
- Dual temperature compensation systems, located on the IMU board and FMU board respectively.
|
|
Temperature is controlled by onboard heating resistors to achieve the optimal operating temperature for the IMUs.
|
|
- PWM servo output voltage switchable between 3.3V or 5V.
|
|
- Modular design for DIY carrier boards.
|
|
|
|
### Processors & Sensors
|
|
|
|
- Main Processor: STM32H743XI
|
|
- 32-bit Arm® Cortex®-M7, 480MHz, 2MB Flash, 1MB RAM
|
|
- Onboard Sensors:
|
|
- Accel/Gyro: SCH16T
|
|
- Accel/Gyro: IIM42652
|
|
- Accel/Gyro: IIM42653
|
|
- Magnetometer: RM3100
|
|
- Barometer: BMP581
|
|
- Barometer: ICP-20100
|
|
|
|
### Electrical Data
|
|
|
|
- Rated Voltage:
|
|
- Input Voltage: 10~18V
|
|
- USB Power Input: 4.75~5.25V
|
|
- Servo Rail Input: 0~9.9V
|
|
- Rated Current:
|
|
- Total Output Max Current: 10A
|
|
- `TELEM1` and `TELEM2` Output Current limiter: 4A
|
|
- `CAN1` and `CAN2` Output Current limiter: 2.4A
|
|
- Other Ports Output Current limiter: 1.5A
|
|
|
|
### Interfaces
|
|
|
|
- 16x PWM Servo Outputs
|
|
- 1x Dedicated R/C Input(`RC IN`) for Spektrum / DSM and S.Bus
|
|
- 1x Analog/PWM RSSI Input
|
|
- 2x TELEM Ports (with full flow control)
|
|
- 1x UART4 Port
|
|
- 2x GPS Ports
|
|
- 1x Full GPS plus Safety Switch Port (GPS1)
|
|
- 1x Basic GPS Port (with I2C, GPS2)
|
|
- 1x USB Port (TYPE-C)
|
|
- 1x Ethernet Port
|
|
- Transformerless application
|
|
- 100Mbps
|
|
- 3x I2C Bus Ports
|
|
- 1x SPI Bus
|
|
- 1x Chip Select Line
|
|
- 1x Data Ready Line
|
|
- 1x SPI Reset Line
|
|
- 5x CAN Ports for CAN Peripherals
|
|
- 3x CAN1 Bus Multiplexed Ports
|
|
- 2x CAN2 Bus Multiplexed Ports
|
|
- 2x Power Input Ports
|
|
- DroneCAN/UAVCAN Power Input
|
|
- 2x AD Ports
|
|
- Analog Input (3.3V)
|
|
- Analog Input (6.6V - not supported by PX4)
|
|
- 1x Dedicated Debug Port
|
|
- FMU Debug
|
|
|
|
### Mechanical Data
|
|
|
|
- Dimensions:
|
|
|
|
|
|
|
|
## Purchase Channels {#store}
|
|
|
|
Order from [CUAV](https://store.cuav.net/).
|
|
|
|
## Assembly/Setup
|
|
|
|
The [X25 SUPER Wiring Quick Start](../assembly/quick_start_cuav_x25_evo.md) provides instructions on how to assemble required/important peripherals including GPS, Power Module etc.
|
|
|
|
## Pinouts
|
|
|
|
|
|
|
|
|
|
## Serial Port Mapping
|
|
|
|
| UART | Device | Port |
|
|
| ------ | ---------- | ------------- |
|
|
| USART1 | /dev/ttyS0 | GPS1 |
|
|
| USART2 | /dev/ttyS1 | GPS2 |
|
|
| USART3 | /dev/ttyS2 | Debug Console |
|
|
| UART4 | /dev/ttyS3 | UART4 |
|
|
| UART5 | /dev/ttyS4 | TELEM2 |
|
|
| USART6 | /dev/ttyS5 | RC IN |
|
|
| UART7 | /dev/ttyS6 | TELEM1 |
|
|
|
|
## RC Input
|
|
|
|
The RC input pin is directly connected to the FMU UART6 TX.
|
|
|
|
## Voltage Ratings
|
|
|
|
The _X25-SUPER_ achieves triple redundancy on power supplies if three power sources are provided.
|
|
The three power rails are `POWERC1`, `POWERC2`, and `USB`.
|
|
|
|
- **POWER C1** and **POWER C2** are DroneCAN/UAVCAN battery interfaces.
|
|
|
|
**Normal Operation Maximum Ratings**
|
|
|
|
Under these conditions, all power sources will be used to power the system in the following order:
|
|
|
|
1. **POWER C1** and **POWER C2** Inputs (10V to 18V)
|
|
2. USB Input (4.75V to 5.25V)
|
|
|
|
**Voltage monitoring**
|
|
|
|
Digital DroneCAN/UAVCAN battery monitoring is enabled by default.
|
|
|
|
## Building Firmware
|
|
|
|
::: tip
|
|
Most users will not need to build this firmware (from PX4 v1.18).
|
|
It is pre-built and automatically installed by _QGroundControl_ when appropriate hardware is connected.
|
|
:::
|
|
|
|
To [build PX4](../dev_setup/building_px4.md) for this target, execute:
|
|
|
|
```sh
|
|
make cuav_x25-super_default
|
|
```
|
|
|
|
## Debug Port {#debug_port}
|
|
|
|
The [PX4 System Console](../debug/system_console.md) and [SWD Interface](../debug/swd_debug.md) operate on the **FMU Debug** port.
|
|
|
|
| Pin | Signal | Volt |
|
|
| ------- | -------------- | ----- |
|
|
| 1 (red) | 5V+ | +5V |
|
|
| 2 (blk) | DEBUG TX (OUT) | +3.3V |
|
|
| 3 (blk) | DEBUG RX (IN) | +3.3V |
|
|
| 4 (blk) | FMU_SWDIO | +3.3V |
|
|
| 5 (blk) | FMU_SWCLK | +3.3V |
|
|
| 6 (blk) | GND | GND |
|
|
|
|
## Supported Platforms / Airframes
|
|
|
|
Any multicopter / airplane / rover or boat that can be controlled with normal RC servos or Futaba S-Bus servos.
|
|
The complete set of supported configurations can be seen in the [Airframes Reference](../airframes/airframe_reference.md).
|
|
|
|
## Further info
|
|
|
|
- [CUAV Docs](https://doc.cuav.net/)
|