mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-05-15 22:37:35 +08:00
PX4 Build Bot
87 lines
4.4 KiB
Markdown
87 lines
4.4 KiB
Markdown
# Aion Robotics R1 UGV
|
|
|
|
<Badge type="tip" text="PX4 v1.15" />
|
|
|
|
The [Aion R1](https://www.aionrobotics.com/) vehicle was chosen to test and improve the differential drive support for PX4, and to improve driver support for Roboclaw Motor Controllers, such as the [RoboClaw 2x15A](https://www.basicmicro.com/RoboClaw-2x15A-Motor-Controller_p_10.html).
|
|
|
|
The documentation and driver information here should also make it easier to work with Roboclaw controllers on other vehicles, and to work with vehicles like the [Aion R6](https://www.aionrobotics.com/r6).
|
|
|
|
Currently, PX4 supports MANUAL mode for this setup.
|
|
|
|
|
|
|
|
## 부품 목록
|
|
|
|
- [Aion R1 (Discontinued)](https://www.aionrobotics.com/)
|
|
- [Documentation](https://github-docs.readthedocs.io/en/latest/r1-ugv.html)
|
|
- [RoboClaw 2x15A](https://www.basicmicro.com/RoboClaw-2x15A-Motor-Controller_p_10.html)
|
|
- [R1 Roboclaw specifications](https://resources.basicmicro.com/aion-robotics-r1-autonomous-robot/)
|
|
- [Auterion Skynode](../companion_computer/auterion_skynode.md)
|
|
|
|
## 조립
|
|
|
|
The assembly consists of a 3D-printed frame on which all the autopilot parts were attached.
|
|
For this build this includes an [Auterion Skynode](../companion_computer/auterion_skynode.md), connected to a Pixhawk Adapter Board that interfaces with the RoboClaw motor controllers over serial.
|
|
|
|
|
|
|
|
:::info
|
|
If using a standard Pixhawk you could connect the RoboClaw to the Autopilot without an Adapter Board.
|
|
:::
|
|
|
|
The RoboClaw should be connected to a suitable suitable serial (UART) port on the flight controller, such as `GPS2` or `TELEM1`.
|
|
Other RoboClaw wiring is detailed in the [RoboClaw User Manual](https://downloads.basicmicro.com/docs/roboclaw_user_manual.pdf) 'Packet Serial Wiring' section and shown below (this setup has been validated for compatibility).
|
|
|
|
|
|
|
|
## PX4 설정
|
|
|
|
### Rover Configuration
|
|
|
|
Use _QGroundControl_ for rover configuration:
|
|
|
|
1. In the [Basic Configuration](../config/index.md) section, select the [Airframe](../config/airframe.md) tab.
|
|
2. Choose **Aion Robotics R1 UGV** under the **Rover** category.
|
|
|
|
|
|
|
|
### RoboClaw Configuration
|
|
|
|
First configure the serial connection:
|
|
|
|
1. Navigate to the [Parameters](../advanced_config/parameters.md) section in QGroundControl.
|
|
|
|
- Set the [RBCLW_SER_CFG](../advanced_config/parameter_reference.md#RBCLW_SER_CFG) parameter to the serial port to which the RoboClaw is connected (such as `GPS2`).
|
|
- [RBCLW_COUNTS_REV](../advanced_config/parameter_reference.md#RBCLW_COUNTS_REV) specifies the number of encoder counts required for one wheel revolution.
|
|
This value should be left at `1200` for the tested `RoboClaw 2x15A Motor Controller`.
|
|
Adjust the value based on your specific encoder and wheel setup.
|
|
- RoboClaw motor controllers must be assigned a unique address on the bus.
|
|
The default address is 128 and you should not need to change this (if you do, update the PX4 parameter [RBCLW_ADDRESS](../advanced_config/parameter_reference.md#RBCLW_ADDRESS) to match).
|
|
|
|
::: info
|
|
PX4 does not support multiple RoboClaw motor controllers in the same vehicle — each controller needs a unique address on the bus, and there is only one parameter for setting the address in PX4 (`RBCLW_ADDRESS`).
|
|
|
|
:::
|
|
|
|
Then configure the actuator configuration:
|
|
|
|
1. Navigate to [Actuators Configuration & Testing](../config/actuators.md) in QGroundControl.
|
|
2. Select the RoboClaw driver from the list of _Actuator Outputs_.
|
|
|
|
For the channel assignments, disarm, minimum, and maximum values, please refer to the image below.
|
|
|
|
|
|
|
|
For systems with more than two motors, it is possible to assign the same function to several motors.
|
|
The reason for the unusual values, can be found in the [RoboClaw User Manual](https://downloads.basicmicro.com/docs/roboclaw_user_manual.pdf) under `Compatibility Commands` for `Packet Serial`:
|
|
|
|
```plain
|
|
Drive motor forward. Valid data range is 0 - 127. A value of 127 = full speed forward, 64 =
|
|
about half speed forward and 0 = full stop.
|
|
```
|
|
|
|
## See also
|
|
|
|
- [roboclaw](../modules/modules_driver.md#roboclaw) driver
|
|
- [Roboclaw User Manual](https://downloads.basicmicro.com/docs/roboclaw_user_manual.pdf)
|