fly316/PX4-Autopilot
7
0
Fork 0
mirror of https://gitee.com/mirrors_PX4/PX4-Autopilot.git synced 2026-04-14 10:07:39 +08:00
Code Issues Packages Projects Releases Wiki Activity
PX4-Autopilot/docs/zh/flight_controller/durandal.md
PX4 Build Bot faedf252b3
New Crowdin translations - zh-CN (#25965) 
Co-authored-by: Crowdin Bot <support+bot@crowdin.com>
2025-11-24 07:21:18 +11:00

422 lines
16 KiB
Markdown
Raw Permalink Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

# Holybro Durandal
:::warning
PX4 does not manufacture this (or any) autopilot.
Contact the [manufacturer](https://holybro.com/) for hardware support or compliance issues.
:::
_Durandal_<sup>&reg;</sup> is the latest update to the successful family of Holybro flight controllers.
It was designed and developed by Holybro.
![Durandal](../../assets/flight_controller/durandal/durandal_hero.jpg)
At high level, some of the key features are:
- Integrated temperature control for sensors.
- Powerful STM32H7 microcontroller running at 480MHz.
2 MB of Flash memory and 1 MB of RAM.
- New sensors with higher temperature stability.
- Internal vibration isolation system.
- Dual high-performance, low-noise IMUs on board are designed for demanding stabilization applications.
A summary of the key features, [assembly](../assembly/quick_start_durandal.md), and [purchase](#purchase) links can be found below.
:::info
This flight controller is [manufacturer supported](../flight_controller/autopilot_manufacturer_supported.md).
:::
## 总览
#### Technical Specifications
- Main FMU Processor: STM32H743
- 32 Bit Arm ® Cortex® -M7, 480MHz, 2MB memory, 1MB RAM
- IO 处理器：STM32F100
- 32 Bit Arm ® Cortex® -M3, 24MHz, 8KB SRAM
- On-board sensors
- 加速度计 / 陀螺仪：ICM-20689
- Accel/Gyro: BMI088 or ICM20602
- Mag: IST8310
- 气压计：MS5611
- GPS：ublox Neo-M8N GPS/GLONASS 接收器；集成磁力计 IST8310
#### 接口
- 8-13 PWM servo outputs (8 from IO, 5 from FMU)
- FMU上有6个专用PWM/Capture输入
- Dedicated R/C input for Spektrum / DSM
- Dedicated R/C input for CPPM and S.Bus
- Dedicated S.Bus servo output and analog / PWM RSSI input
- 5个通用串行口
- 3 with full flow control
- 1 with separate 1.5A current limit
- 3 个 I2C 接口
- 4路SPI总线
- 1 internal high speed SPI sensor bus with 4 chip selects and 6 DRDYs
- 1 internal low noise SPI bus dedicated for XXX
- Barometer with 2 chip selects, no DRDYs
- 1 internal SPI bus dedicated for FRAM
- Supports temperature control located on sensor module
- 1 external SPI buses
- Up to 2 CANBuses for dual CAN
- Each CANBus has individual silent controls or ESC RX-MUX control
- 2个电池电流/电压模拟输入口
- 2 additional analog inputs
#### Electrical Data
- 电源模块输出：4.9~5.5V
- Max input voltage: 6V
- 最大电流感应：120A
- USB 电源输入：4.75~5.25V
- 伺服导轨输入电压：0~36V
#### Mechanical Data
- Dimensions: 80x45x20.5mm
- 重量：68.8g
#### 其它特性
- Operating temperature: ~40~85C
- Storage temperature: -40~85C
- CE
- FCC
- RoHS compliant (lead-free)
For more information see: [Durandal Technical Data Sheet](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Durandal_technical_data_sheet_90f8875d-8035-4632-a936-a0d178062077.pdf).
<a id="purchase"></a>
## 购买渠道
Order from [Holybro](https://holybro.com/products/durandal).
## Connections
The locations of ports/connections are shown here (and below in the [pinouts section](#pinouts)).
### Top
![Durandal - Top Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_top.jpg)
### Front
![Durandal - Front Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_front.jpg)
### Back
![Durandal - Back Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_back.jpg)
### Right
![Durandal - Right-side Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_right.jpg)
### Left
![Durandal - Left-side Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_left.jpg)
## 尺寸
All dimensions are in millimeters.
![Durandal Dimensions](../../assets/flight_controller/durandal/durandal_dimensions.jpg)
<!--
## Voltage Ratings
*Pixhawk 4* can be triple-redundant on the power supply if three power sources are supplied. The three power rails are: **POWER1**, **POWER2** and **USB**.
::: info
The output power rails **FMU PWM OUT** and **I/O PWM OUT** (0V to 36V) do not power the flight controller board (and are not powered by it).
You must supply power to one of **POWER1**, **POWER2** or **USB** or the board will be unpowered.
:::
**Normal Operation Maximum Ratings**
Under these conditions all power sources will be used in this order to power the system:
1. **POWER1** and **POWER2** inputs (4.9V to 5.5V)
1. **USB** input (4.75V to 5.25V)
-->
<!--
**Absolute Maximum Ratings**
Under these conditions the system will not draw any power (will not be operational), but will remain intact.
1. **POWER1** and **POWER2** inputs (operational range 4.1V to 5.7V, 0V to 10V undamaged)
1. **USB** input (operational range 4.1V to 5.7V, 0V to 6V undamaged)
1. Servo input: VDD_SERVO pin of **FMU PWM OUT** and **I/O PWM OUT** (0V to 42V undamaged)
-->
## 组装 / 设置
The [Durandal Wiring Quick Start](../assembly/quick_start_durandal.md) provides instructions on how to assemble required/important peripherals including GPS, Power Management Board etc.
## 编译固件
:::tip
Most users will not need to build this firmware!
It is pre-built and automatically installed by _QGroundControl_ when appropriate hardware is connected.
:::
To [build PX4](../dev_setup/building_px4.md) for this target:
```
make holybro_durandal-v1_default
```
## 串口映射
| UART | 设备 | Port |
| ------ | ---------- | ----------- |
| USART1 | UART | GPS1 |
| USART2 | /dev/ttyS1 | TELEM1 |
| USART3 | /dev/ttyS2 | TELEM2 |
| UART4 | /dev/ttyS3 | TELEM4/GPS2 |
| USART6 | /dev/ttyS4 | TELEM3 |
| UART7 | /dev/ttyS5 | 调试控制台 |
| UART8 | /dev/ttyS6 | PX4IO |
<!-- Note: Got ports using https://github.com/PX4/PX4-user_guide/pull/672#issuecomment-598198434 -->
## Debug Port {#debug_port}
The [PX4 System Console](../debug/system_console.md) and [SWD interface](../debug/swd_debug.md) run on the _Debug Port_.
The pinouts and connector comply with the [Pixhawk Debug Mini](../debug/swd_debug.md#pixhawk-debug-mini) interface defined in the [Pixhawk Connector Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-009%20Pixhawk%20Connector%20Standard.pdf).
For wiring and debugging information see the above links.
:::info
No Debug port is exposed for the I/O board.
:::
## 外部设备
- [Digital Airspeed Sensor](https://store-drotek.com/793-digital-differential-airspeed-sensor-kit-.html)
- [Telemetry Radio Modules](../telemetry/index.md)
- [Rangefinders/Distance sensors](../sensor/rangefinders.md)
## 支持的平台/机身
Any multicopter / airplane / rover or boat that can be controlled with normal RC servos or Futaba S-Bus servos.
The complete set of supported configurations can be seen in the [Airframes Reference](../airframes/airframe_reference.md).
## 针脚定义
_Durandal_ pinouts are listed below.
These can also be downloaded from [here](https://cdn.shopifycdn.net/s/files/1/0604/5905/7341/files/Durandal_Pinouts_v1.0.pdf?v=1693983344).
### Top Pinouts
![Durandal - Top Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_top.jpg)
### Front Pinouts
![Durandal - Front Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_front.jpg)
#### SUBS Out port
| 针脚 | 信号 | 电压 |
| ----------------------------- | ---------------------------------------------------------- | --------------------- |
| 1（红） | - | - |
| 2 (yellow) | SBUS_OUT/RSSI_IN | +3.3V |
| 3 (black) | GND | GND |
#### DSM RC port
| 针脚 | 信号 | 电压 |
| ----------------------------- | ---------------------------- | --------------------- |
| 1（红） | VDD_3V3 | +3.3V |
| 2 (yellow) | DSM_IN | +3.3V |
| 3 (black) | GND | GND |
#### I2C A port
| 针脚 | 信号 | 电压 |
| ---------------------------- | ---- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | SCL4 | +3.3V |
| 3 (black) | SDA4 | +3.3V |
| 4 (black) | GND | GND |
#### CAN1 port
| 针脚 | 信号 | 电压 |
| ---------------------------- | ----- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | CAN H | +3.3V |
| 3 (black) | CAN L | +3.3V |
| 4 (black) | GND | GND |
<a id="gps"></a>
#### GPS 接口
| 针脚 | 信号 | 电压 |
| ----------------------------- | ----------------------------------------------------------- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | TX (out) | +3.3V |
| 3 (black) | RX (in) | +3.3V |
| 4 (black) | SCL1 | +3.3V |
| 5 (black) | SDA1 | +3.3V |
| 6 (black) | SAFETY_SWITCH | +3.3V |
| 7 (black) | SAFETY_SWITCH_LED | +3.3V |
| 8 (black) | VDD_3V3 | +3.3V |
| 9 (black) | BUZZER | +5V |
| 10 (black) | GND | GND |
<a id="telem4_i2cb"></a>
#### TELEM4 I2CB ports
| 针脚 | 信号 | 电压 |
| ---------------------------- | --------------------------- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | TX (out) | +3.3V |
| 3 (black) | RX (in) | - |
| 4 (black) | SCL2 | - |
| 5 (black) | SDA2 | +3.3V |
| 6 (black) | GND | GND |
<a id="telem1_2_3"></a>
#### TELEM3, TELEM2, TELEM1 port
| 针脚 | 信号 | 电压 |
| ---------------------------- | --------------------------- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | TX (out) | +3.3V |
| 3 (black) | RX (in) | +3.3V |
| 4 (black) | CTS（输入） | +3.3V |
| 5 (black) | RTS（输出） | +3.3V |
| 6 (black) | GND | GND |
<a id="power"></a>
#### POWER port
| 针脚 | 信号 | 电压 |
| ---------------------------- | --- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | VCC | +5V |
| 3 (black) | 电流 | +3.3V |
| 4 (black) | 电压 | +3.3V |
| 5 (black) | GND | GND |
| 6 (black) | GND | GND |
### Back Pinouts
![Durandal - Back Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_back.jpg)
#### MAIN Out
| 针脚 | 信号 | 电压 | + | - |
| -- | --------------------------- | --------------------- | ------------------------------ | --- |
| 1 | IO_CH1 | +3.3V | VDD_SERVO | GND |
| 2 | IO_CH2 | +3.3V | VDD_SERVO | GND |
| 3 | IO_CH3 | +3.3V | VDD_SERVO | GND |
| 4 | IO_CH4 | +3.3V | VDD_SERVO | GND |
| 5 | IO_CH5 | +3.3V | VDD_SERVO | GND |
| 6 | IO_CH6 | +3.3V | VDD_SERVO | GND |
| 7 | IO_CH7 | +3.3V | VDD_SERVO | GND |
| 8 | IO_CH8 | +3.3V | VDD_SERVO | GND |
#### AUX Out
| 针脚 | 信号 | 电压 | + | - |
| -- | ---------------------------- | --------------------- | ------------------------------ | --- |
| 1 | FMU_CH1 | +3.3V | VDD_SERVO | GND |
| 2 | FMU_CH2 | +3.3V | VDD_SERVO | GND |
| 3 | FMU_CH3 | +3.3V | VDD_SERVO | GND |
| 4 | FMU_CH4 | +3.3V | VDD_SERVO | GND |
| 5 | FMU_CH5 | +3.3V | VDD_SERVO | GND |
#### RC IN
| 针脚 | 信号 | 电压 |
| -- | -------------------------------------------------------- | --------------------- |
| S | SBUS_IN/PPM_IN | +3.3V |
| + | VCC | +5V |
| - | GND | GND |
### Right-side Pinouts
![Durandal - Right-side Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_right.jpg)
#### CAN2 port
| 针脚 | 信号 | 电压 |
| ---------------------------- | ----- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | CAN H | +3.3V |
| 3 (black) | CAN L | +3.3V |
| 4 (black) | GND | GND |
#### CAP & ADC IN port
| 针脚 | 信号 | 电压 |
| ----------------------------- | ------------------------------------------------------ | ---------------------------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | FMU_CAP6 | +3.3V |
| 3 (black) | FMU_CAP5 | +3.3V |
| 4 (black) | FMU_CAP4 | +3.3V |
| 5 (black) | FMU_CAP3 | +3.3V |
| 6 (black) | FMU_CAP2 | +3.3V |
| 7 (black) | FMU_CAP1 | +3.3V |
| 8 (black) | ADC1_SPARE_1 | +3.3V [++](#warn_sensor) |
| 9 (black) | ADC1_SPARE_2 | +6.6V [++](#warn_sensor) |
| 10 (black) | GND | GND |
<a id="warn_sensor"></a>
:::warning
\++ Sensors connected to pins 8, 9 must not send a signal exceeding the indicated voltage.
:::
### Left-side Pinouts
![Durandal - Left-side Pinouts (Schematic)](../../assets/flight_controller/durandal/durandal_pinouts_left.jpg)
<a id="debug_port"></a>
#### DEBUG port
| 针脚 | 信号 | 电压 |
| ---------------------------- | ----- | --------------------- |
| 1（红） | VT | +3.3V |
| 2 (black) | TX | +3.3V |
| 3 (black) | RX | +3.3V |
| 4 (black) | SWDIO | +3.3V |
| 5 (black) | SWCLK | +3.3V |
| 6 (black) | GND | GND |
#### SPI port
| 针脚 | 信号 | 电压 |
| ---------------------------- | ---- | --------------------- |
| 1（红） | VCC | +5V |
| 2 (black) | SCK | +3.3V |
| 3 (black) | MISO | +3.3V |
| 4 (black) | MOSI | +3.3V |
| 5 (black) | CS1 | +3.3V |
| 6 (black) | CS2 | +3.3V |
| 7 (black) | GND | GND |
#### USB port
| 针脚 | 信号 | 电压 |
| ---------------------------- | ---- | --------------------- |
| 1（红） | VBUS | +5V |
| 2 (black) | DM | +3.3V |
| 3 (black) | DP | +3.3V |
| 4 (black) | GND | GND |
## 更多信息
- [Durandal Wiring QuickStart](../assembly/quick_start_durandal.md)
- [Durandal Technical Data Sheet](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Durandal_technical_data_sheet_90f8875d-8035-4632-a936-a0d178062077.pdf)
- [Durandal Pinouts](https://cdn.shopifycdn.net/s/files/1/0604/5905/7341/files/Durandal_Pinouts_v1.0.pdf?v=1693983344) (Holybro)
Reference in New Issue View Git Blame Copy Permalink