mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
177 lines
6.4 KiB
Markdown
177 lines
6.4 KiB
Markdown
# S-Vehicle E2
|
||
|
||
:::warning
|
||
PX4 не розробляє цей (або будь-який інший) автопілот.
|
||
:::
|
||
|
||
The _E2_ is an advanced autopilot manufactured by S-Vehicle<sup>®</sup>.
|
||
|
||
The autopilot is recommended for commercial system integration, but is also suitable for academic research and any other applications.
|
||
It brings you ultimate performance, stability, and reliability in every aspect.
|
||
|
||
|
||
|
||
:::info
|
||
These flight controllers are [manufacturer supported](../flight_controller/autopilot_manufacturer_supported.md).
|
||
:::
|
||
|
||
### Processors & Sensors
|
||
|
||
- FMU Processor: STM32H753IIK6
|
||
- 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
|
||
- IO Processor: STM32F103
|
||
- 32 Bit Arm® Cortex®-M3, 72MHz, 20KB SRAM
|
||
- Сенсори на платі
|
||
- Акселератор/гіроскоп: BMI088
|
||
- Accel/Gyro: ICM-42688-P
|
||
- Accel/Gyro: ICM-20649
|
||
- Mag: RM3100
|
||
- Барометр: 2x ICP-20100
|
||
|
||
### Інтерфейси
|
||
|
||
- 14x PWM Servo Outputs
|
||
- 1x Dedicated R/C Input for Spektrum / DSM and S.Bus
|
||
- 1x Analog/PWM RSSI Input
|
||
- 2x TELEM Ports (with full flow control)
|
||
- 1x UART4 Port
|
||
- 2x GPS Ports
|
||
- 1x Full GPS plus Safety Switch Port (GPS1)
|
||
- 1x Basic GPS Port (with I2C, GPS2)
|
||
- 1x USB Port (TYPE-C)
|
||
- 1x Ethernet Port
|
||
- Transformerless application
|
||
- 100Mbps
|
||
- 3x I2C Bus Ports
|
||
- 1x SPI Bus
|
||
- 1x Chip Select Line
|
||
- 1x Data Ready Line
|
||
- 1x SPI Reset Line
|
||
- 2x CAN Ports
|
||
- 3x Power Input Ports
|
||
- ADC Power Input
|
||
- I2C Power Input
|
||
- DroneCAN/UAVCAN Power Input
|
||
- 2x AD Ports
|
||
- Analog Input (3.3V)
|
||
- Analog Input (6.6V - not supported by PX4)
|
||
- 1x Dedicated Debug Port
|
||
- FMU Debug
|
||
|
||
## Purchase Channels
|
||
|
||
Order from [S-Vehicle](https://svehicle.cn/).
|
||
|
||
## Радіоуправління
|
||
|
||
A Radio Control (RC) system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes).
|
||
|
||
Вам буде потрібно вибрати сумісний передавач/приймач та потім зв'язати їх, щоб вони взаємодіяли (прочитайте інструкції, що додаються до вашого конкретного передавача/приймача).
|
||
|
||
Spektrum/DSM receivers connect to the DSM/SBUS RC input.
|
||
PPM or SBUS receivers connect to the RC IN input port.
|
||
CRSF receiver must be wired to a spare port (UART) on the Flight Controller. Then you can bind the transmitter and receiver together.
|
||
|
||
## Налаштування послідовного порту
|
||
|
||
| UART | Пристрій | Порт |
|
||
| ------ | ---------- | ------------- |
|
||
| USART1 | /dev/ttyS0 | GPS |
|
||
| USART2 | /dev/ttyS1 | TELEM3 |
|
||
| USART3 | /dev/ttyS2 | Debug Console |
|
||
| UART4 | /dev/ttyS3 | UART4 |
|
||
| UART5 | /dev/ttyS4 | TELEM2 |
|
||
| USART6 | /dev/ttyS5 | PX4IO/RC |
|
||
| UART7 | /dev/ttyS6 | TELEM1 |
|
||
| UART8 | /dev/ttyS7 | GPS2 |
|
||
|
||
## PWM Output
|
||
|
||
The E2-Plus flight controller supports up to 14 PWM outputs.
|
||
The first 8 outputs (labelled M1 to M8) are controlled by a dedicated STM32F103 IOMCU controller.
|
||
The remaining 6 outputs (labelled 9 to 14) are the "auxiliary" outputs.
|
||
These are directly attached to the STM32H753 FMU controller .
|
||
|
||
The 14 PWM outputs are:
|
||
|
||
M1 - M8 are connected to the IOMCU
|
||
A1 - A6 are connected to the FMU
|
||
|
||
M1 - M8 support DShot and are in 3 groups:
|
||
|
||
- M1, M2 in group 1
|
||
- M3, M4 in group 2
|
||
- M5, M6, M7, M8 in group 3
|
||
|
||
The 6 FMU PWM outputs are in 2 groups:
|
||
|
||
A1 - A4 are in one group.
|
||
A5, A6 are in a 2nd group.
|
||
|
||
Channels within the same group need to use the same output rate.
|
||
If any channel in a group uses DShot then all channels in the group need to use DShot.
|
||
|
||
### Електричні дані
|
||
|
||
- Номінальна напруга:
|
||
- Максимальна вхідна напруга: 5,7 В
|
||
- Вхід USB Power: 4.75~5.25V
|
||
- Вхід на серворейку: 0\~9.9В
|
||
- Номінальний струм:
|
||
- Комбінований обмежувач вихідного струму TELEM1 і GPS2: 1,5 А
|
||
- Комбінований обмежувач вихідного струму всіх інших портів: 1.5A
|
||
|
||
## Battery Monitoring
|
||
|
||
The board has connectors for 3 power monitors.
|
||
|
||
- POWER1 -- ADC
|
||
- POWER2 -- DroneCAN
|
||
- POWER3 -- I2C
|
||
|
||
The board is configure by default for a analog power monitor, and also has DroneCAN power monitor and I2C defaults configured which is enabled.
|
||
|
||
The default PDB included with the E2+ is analog and must be connected to `POWER1`.
|
||
|
||
## Збірка прошивки
|
||
|
||
To [build PX4](../dev_setup/building_px4.md) for this target, execute:
|
||
|
||
```sh
|
||
make svehicle_e2_default
|
||
```
|
||
|
||
## Відладочний порт
|
||
|
||
The [PX4 System Console](../debug/system_console.md) and [SWD Interface](../debug/swd_debug.md) operate on the **FMU Debug** port.
|
||
|
||
| Pin | Сигнал | Вольтаж |
|
||
| -------------------------- | --------------------------------- | --------------------- |
|
||
| 1 (red) | 5V+ | +5V |
|
||
| 2 (blk) | DEBUG TX (OUT) | +3.3V |
|
||
| 3 (blk) | DEBUG RX (IN) | +3.3V |
|
||
| 4 (blk) | FMU_SWDIO | +3.3V |
|
||
| 5 (blk) | FMU_SWCLK | +3.3V |
|
||
| 6 (blk) | GND | GND |
|
||
|
||
Інформацію про використання цього порту див:
|
||
|
||
- [SWD Debug Port](../debug/swd_debug.md)
|
||
- [PX4 System Console](../debug/system_console.md) (Note, the FMU console maps to USART3).
|
||
- All ports use GH1.25 ,power ports use ports on E2 uses the 6 circuit [2.00mm Pitch CLIK-Mate Wire-to-Board PCB Receptacle](https://www.molex.com/en-us/products/part-detail/5024430670).
|
||
|
||
## Схема розташування виводів
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
## Підтримувані платформи / Конструкції
|
||
|
||
Any multirotor/airplane/rover or boat that can be controlled using normal RC servos or Futaba S-Bus servos.
|
||
The complete set of supported configurations can be found in the [Airframe Reference](../airframes/airframe_reference.md).
|