PX4-Autopilot/docs/ko/flight_controller/pixhawk6x_pro.md

# Holybro Pixhawk 6X Pro

:::warning
PX4 does not manufacture this (or any) autopilot.
Contact the [manufacturer](https://holybro.com/) for hardware support or compliance issues.
:::

![Pixhawk6X Pro Internal Architecture](../../assets/flight_controller/pixhawk6x_pro/pixhawk6x_pro_internal_architecture.jpeg)

## Key Design Points

- High-performance ADIS16470 Industrial IMU with high accelerometer dynamic range (±40 g), perfect for accurate motion sensing in demanding UAV applications
- All new advanced durable vibration isolation material with resonance frequency in the higher spectrum, ideal for industrial and commercial drone applications
- High performance STM32H753 Processor
- Ethernet interface for high-speed mission computer integration

## Baseboards

The Pixhawk 6X Pro can be purchased with a number of baseboards (or no baseboard) to suit different use cases and vehicle types, including [Standard v2A](https://docs.holybro.com/autopilot/pixhawk-baseboards/pixhawk-baseboard-v2-ports), [Standard v2B](https://docs.holybro.com/autopilot/pixhawk-baseboards/pixhawk-baseboard-v2-ports), and [Mini](https://docs.holybro.com/autopilot/pixhawk-baseboards/pixhawk-mini-baseboard-ports), which are shown below.
It can also be used with any other Pixhawk Autopilot Bus (PAB) specification-compliant baseboard, such as the [Holybro Pixhawk Jetson Baseboard](../companion_computer/holybro_pixhawk_jetson_baseboard.md) and [Holybro Pixhawk RPi CM4 Baseboard](../companion_computer/holybro_pixhawk_rpi_cm4_baseboard.md).

:::: tabs

:::tab Pixhawk 6X Pro Standard v2A

![Pixhawk 6X Pro Standard v2A](../../assets/flight_controller/pixhawk6x_pro/pixhawk6x_pro_v2a.webp)

:::

:::tab Pixhawk 6X Pro Standard v2B

![Pixhawk 6X Pro Standard v2B](../../assets/flight_controller/pixhawk6x_pro/pixhawk6x_pro_v2b.webp)
:::

:::tab Pixhawk 6X Pro Mini

![Pixhawk 6X Pro Mini](../../assets/flight_controller/pixhawk6x_pro/pixhawk6x_pro_mini.webp)
:::

::::

## 특징

- Triple redundant IMU & double redundant barometer on separate buses
- Modular flight controller: separated IMU, FMU, and Base system
- Safety-driven design incorporates sensors from different manufacturers and model lineups
- Independent LDO powers every sensor set with independent power control.
- Temperature-controlled IMU board, allowing optimum working temperature of IMUs

:::details
Processors & Sensors

- FMU Processor: STM32H753
  - 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
- IO Processor: STM32F103
  - 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
- 내장 센서 :
  - Accel/Gyro: ADIS16470 (±40g, Vibration Isolated, Industrial IMU)
  - Accel/Gyro: IIM-42652 (±16g, Vibration Isolated, Industrial IMU)
  - Accel/Gyro: ICM-45686 with BalancedGyro™ Technology (±32g, Hard Mounted)
  - Barometer: ICP20100
  - Barometer: BMP388
  - Mag: BMM150

:::

:::details
Electrical data

- Voltage Ratings:
  - 최대 입력 전압: 6V
  - USB 전원 입력: 4.75~5.25V
  - 서보 레일 입력: 0~36V
- Current Ratings: - Telem1 output current limiter: 1.5A - All other port combined output current limiter: 1.5A

:::

:::details
Mechanical data

- 크기
  - Flight Controller Module: 38.8 x 31.8 x 30.1mm
  - Standard Baseboard: 52.4 x 103.4 x 16.7mm
  - Mini Baseboard: 43.4 x 72.8 x 14.2 mm
- Weight - Flight Controller Module: 50g - Standard Baseboard: 51g - Mini Baseboard: 26.5g

:::

:::details
인터페이스

- 16- PWM servo outputs
- R/C input for Spektrum / DSM
- Dedicated R/C input for PPM and S.Bus input
- Dedicated analog / PWM RSSI input and S.Bus output
- 범용 시리얼 포트 4개
  - 전체 흐름 제어 3개
  - 1 with separate 1.5A current limit (Telem1)
  - 1 with I2C and additional GPIO line for external NFC reader
- 2 GPS ports
  - 1 full GPS plus Safety Switch Port
  - 1 basic GPS port
- 1 I2C port
- 1 Ethernet port
  - Transformerless Applications
  - 100Mbps
- 1 SPI bus
  - 2 chip select lines
  - 2 data-ready lines
  - 1 SPI SYNC line
  - 1 SPI reset line
- 2 CAN Buses for CAN peripheral
  - CAN Bus has individual silent controls or ESC RX-MUX control
- 2 Power input ports with SMBus - 1 AD & IO port - 2 additional analog input - 1 PWM/Capture input - 2 Dedicated debug and GPIO lines

:::

## 구매처

Order from [Holybro](https://holybro.com/products/pixhawk-6x-pro).

## 조립 및 설정

The [Pixhawk 6X Wiring Quick Start](../assembly/quick_start_pixhawk6x.md) provides instructions on how to assemble required/important peripherals including GPS, Power Module etc.

## 연결

### Multicopter Wiring Example

![Pixhawk 6X Pro Wiring Overview](../../assets/flight_controller/pixhawk6x_pro/pixhawk6x_pro_wiring_diagram.png)

### VTOL Wiring Example

![Pixhawk 6X Pro VTOL Fixed wing Wiring Overview](../../assets/flight_controller/pixhawk6x_pro/pixhawk6x_pro_wiring_diagram_vtol.webp)

## 핀배열

- [Holybro Pixhawk Baseboard Pinout](https://docs.holybro.com/autopilot/pixhawk-6x/pixhawk-baseboard-pinout)
- [Holybro Pixhawk Mini-Baseboard Pinout](https://docs.holybro.com/autopilot/pixhawk-6x/pixhawk-mini-baseboard-pinout)
- [Holybro Pixhawk Jetson Baseboard](https://docs.holybro.com/autopilot/pixhawk-baseboards/pixhawk-jetson-baseboard)
- [Holybro Pixhawk RPi CM4 Baseboard](https://docs.holybro.com/autopilot/pixhawk-baseboards/pixhawk-rpi-cm4-baseboard)

참고:

- The [camera capture pin](../camera/fc_connected_camera.md#camera-capture-configuration) (`PI0`) is pin 2 on the AD&IO port, marked above as `FMU_CAP1`.

## 시리얼 포트 매핑

| UART   | 장치         | 포트                              |
| ------ | ---------- | ------------------------------- |
| USART1 | /dev/ttyS0 | GPS                             |
| USART2 | /dev/ttyS1 | TELEM3                          |
| USART3 | /dev/ttyS2 | 디버그 콘솔                          |
| UART4  | /dev/ttyS3 | UART4 & I2C |
| UART5  | /dev/ttyS4 | TELEM2                          |
| USART6 | /dev/ttyS5 | PX4IO/RC                        |
| UART7  | /dev/ttyS6 | TELEM1                          |
| UART8  | /dev/ttyS7 | GPS2                            |

## 크기

[Pixhawk 6X Pro Dimensions](https://docs.holybro.com/autopilot/pixhawk-6x-pro/dimensions)

## 정격 전압

_Pixhawk 6X Pro_ can be triple-redundant on the power supply if three power sources are supplied.
The three power rails are: **POWER1**, **POWER2** and **USB**.
The **POWER1** & **POWER2** ports on the Pixhawk 6X uses the 6 circuit [2.00mm Pitch CLIK-Mate Wire-to-Board PCB Receptacle](https://www.molex.com/en-us/products/part-detail/5024430670).

**Normal Operation Maximum Ratings**

이러한 조건에서 전원은 아래의 순서대로 시스템에 전원을 공급하여야합니다.

1. **POWER1** and **POWER2** inputs (4.9V to 5.5V)
2. **USB** input (4.75V to 5.25V)

**Absolute Maximum Ratings**

아래의 조건에서 시스템은 전원을 사용하지 않지만(작동하지 않음), 그대로 유지됩니다.

1. **POWER1** and **POWER2** inputs (operational range 4.1V to 5.7V, 0V to 10V undamaged)
2. **USB** input (operational range 4.1V to 5.7V, 0V to 6V undamaged)
3. Servo input: VDD_SERVO pin of **FMU PWM OUT** and **I/O PWM OUT** (0V to 42V undamaged)

**Voltage monitoring**

Digital I2C battery monitoring is enabled by default (see [Quickstart > Power](../assembly/quick_start_pixhawk6x.md#power)).

:::info
Analog battery monitoring via an ADC is not supported on this particular board, but may be supported in variations of this flight controller with a different baseboard.
:::

## 펌웨어 빌드

:::tip
Most users will not need to build this firmware!
It is pre-built and automatically installed by _QGroundControl_ when appropriate hardware is connected.
:::

To [build PX4](../dev_setup/building_px4.md) for this target:

```
make px4_fmu-v6x_default
```

## 디버그 포트

The [PX4 System Console](../debug/system_console.md) and [SWD interface](../debug/swd_debug.md) run on the **FMU Debug** port.

The pinouts and connector comply with the [Pixhawk Debug Full](../debug/swd_debug.md#pixhawk-debug-full) interface defined in the [Pixhawk Connector Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-009%20Pixhawk%20Connector%20Standard.pdf) interface (JST SM10B connector).

| 핀                           | 신호                                  | 전압                    |
| --------------------------- | ----------------------------------- | --------------------- |
| 1(red)   | `Vtref`                             | +3.3V |
| 2 (흑)    | Console TX (OUT) | +3.3V |
| 3 (흑)    | Console RX (IN)  | +3.3V |
| 4 (흑)    | `SWDIO`                             | +3.3V |
| 5 (흑)    | `SWCLK`                             | +3.3V |
| 6 (흑)    | `SWO`                               | +3.3V |
| 7 (흑)    | NFC GPIO                            | +3.3V |
| 8 (blk)  | PH11                                | +3.3V |
| 9 (blk)  | nRST                                | +3.3V |
| 10 (blk) | `GND`                               | GND                   |

For information about using this port see:

- [SWD Debug Port](../debug/swd_debug.md)
- [PX4 System Console](../debug/system_console.md) (Note, the FMU console maps to USART3).

## 주변 장치

- [Telemetry Radio Modules](https://holybro.com/collections/telemetry-radios?orderby=date)
- [Rangefinders/Distance sensors](../sensor/rangefinders.md)
- [Holybro Sensors](https://holybro.com/collections/sensors)
- [Holybro GPS & RTK Systems](https://holybro.com/collections/gps-rtk-systems)
- [Power Modules & PDBs](https://holybro.com/collections/power-modules-pdbs)

## Supported Platforms/Airframes

일반 RC 서보 또는 Futaba S-Bus 서보로 제어 가능한 모든 멀티콥터/비행기/로버 또는 보트.
The complete set of supported configurations can be seen in the [Airframes Reference](../airframes/airframe_reference.md).

## CAD File

Download [here](https://docs.holybro.com/autopilot/pixhawk-6x-pro/download).

## See Also

- [Holybro Docs](https://docs.holybro.com/autopilot/pixhawk-6x-pro) (Holybro)
- [Pixhawk 6X Wiring QuickStart](../assembly/quick_start_pixhawk6x.md)
- [Pixhawk Autopilot FMUv6X Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-012%20Pixhawk%20Autopilot%20v6X%20Standard.pdf).
- [Pixhawk Autopilot Bus Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-010%20Pixhawk%20Autopilot%20Bus%20Standard.pdf).
- [Pixhawk Connector Standard](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-009%20Pixhawk%20Connector%20Standard.pdf).