Stop expecting CONFIG_HRT_anything since we aren't baking it into the NuttX config anymore.

nuttx-configs/px4fmu-v1/include/board.h

@@ -158,10 +158,8 @@
 
 /* High-resolution timer
  */
-#ifdef CONFIG_HRT_TIMER
-# define HRT_TIMER		1	/* use timer1 for the HRT */
-# define HRT_TIMER_CHANNEL	1	/* use capture/compare channel */
-#endif
+#define HRT_TIMER		1	/* use timer1 for the HRT */
+#define HRT_TIMER_CHANNEL	1	/* use capture/compare channel */
 
 /* LED definitions ******************************************************************/
 /* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any
@@ -241,10 +239,8 @@
  *
  * PPM input is handled by the HRT timer.
  */
-#if defined(CONFIG_HRT_TIMER) && defined (CONFIG_HRT_PPM)
-# define HRT_PPM_CHANNEL	3	/* use capture/compare channel 3 */
-# define GPIO_PPM_IN	(GPIO_ALT|GPIO_AF1|GPIO_SPEED_50MHz|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN10)
-#endif
+#define HRT_PPM_CHANNEL	3	/* use capture/compare channel 3 */
+#define GPIO_PPM_IN	(GPIO_ALT|GPIO_AF1|GPIO_SPEED_50MHz|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN10)
 
 /*
  * CAN

nuttx-configs/px4io-v1/include/board.h

@@ -118,10 +118,8 @@
 /* 
  * High-resolution timer
  */
-#ifdef CONFIG_HRT_TIMER
-# define HRT_TIMER		1	/* use timer1 for the HRT */
-# define HRT_TIMER_CHANNEL	2	/* use capture/compare channel 2 */
-#endif
+#define HRT_TIMER		1	/* use timer1 for the HRT */
+#define HRT_TIMER_CHANNEL	2	/* use capture/compare channel 2 */
 
 /*
  * PPM
@@ -130,10 +128,8 @@
  *
  * Pin is PA8, timer 1, channel 1
  */
-#if defined(CONFIG_HRT_TIMER) && defined (CONFIG_HRT_PPM)
-# define HRT_PPM_CHANNEL	1	/* use capture/compare channel 1 */
-# define GPIO_PPM_IN		GPIO_TIM1_CH1IN
-#endif
+#define HRT_PPM_CHANNEL	1	/* use capture/compare channel 1 */
+#define GPIO_PPM_IN		GPIO_TIM1_CH1IN
 
 /************************************************************************************
  * Public Data

nuttx-configs/px4io-v1/nsh/defconfig

@@ -200,28 +200,6 @@ SERIAL_HAVE_CONSOLE_DMA=y
 CONFIG_USART2_RXDMA=n
 CONFIG_USART3_RXDMA=y
 
-#
-# PX4IO specific driver settings
-#
-# CONFIG_HRT_TIMER
-#   Enables the high-resolution timer.  The board definition must
-#   set HRT_TIMER and HRT_TIMER_CHANNEL to the timer and capture/
-#   compare channels to be used.
-# CONFIG_HRT_PPM
-#   Enables R/C PPM input using the HRT.  The board definition must
-#   set HRT_PPM_CHANNEL to the timer capture/compare channel to be
-#   used, and define GPIO_PPM_IN to configure the appropriate timer
-#   GPIO.
-# CONFIG_PWM_SERVO
-#   Enables the PWM servo driver.  The driver configuration must be
-#   supplied by the board support at initialisation time.
-#   Note that USART2 must be disabled on the PX4 board for this to
-#   be available.
-#
-#
-CONFIG_HRT_TIMER=y
-CONFIG_HRT_PPM=y
-
 #
 # General build options
 #

src/drivers/stm32/drv_hrt.c

@@ -70,7 +70,7 @@
 #include "stm32_gpio.h"
 #include "stm32_tim.h"
 
-#ifdef CONFIG_HRT_TIMER
+#ifdef HRT_TIMER
 
 /* HRT configuration */
 #if   HRT_TIMER == 1
@@ -155,7 +155,7 @@
 #  error must not set CONFIG_STM32_TIM11=y and HRT_TIMER=11
 # endif
 #else
-# error HRT_TIMER must be set in board.h if CONFIG_HRT_TIMER=y
+# error HRT_TIMER must be a value between 1 and 11
 #endif
 
 /*
@@ -275,7 +275,7 @@ static void		hrt_call_invoke(void);
 /*
  * Specific registers and bits used by PPM sub-functions
  */
-#ifdef CONFIG_HRT_PPM
+#ifdef HRT_PPM_CHANNEL
 /* 
  * If the timer hardware doesn't support GTIM_CCER_CCxNP, then we will work around it.
  *
@@ -326,7 +326,7 @@ static void		hrt_call_invoke(void);
 #  define CCER_PPM	(GTIM_CCER_CC4E | GTIM_CCER_CC4P | GTIM_CCER_CC4NP) /* CC4, both edges */
 #  define CCER_PPM_FLIP	GTIM_CCER_CC4P
 # else
-#  error HRT_PPM_CHANNEL must be a value between 1 and 4 if CONFIG_HRT_PPM is set
+#  error HRT_PPM_CHANNEL must be a value between 1 and 4
 # endif
 
 /*
@@ -377,7 +377,7 @@ static void	hrt_ppm_decode(uint32_t status);
 # define CCMR1_PPM	0
 # define CCMR2_PPM	0
 # define CCER_PPM	0
-#endif /* CONFIG_HRT_PPM */
+#endif /* HRT_PPM_CHANNEL */
 
 /*
  * Initialise the timer we are going to use.
@@ -424,7 +424,7 @@ hrt_tim_init(void)
 	up_enable_irq(HRT_TIMER_VECTOR);
 }
 
-#ifdef CONFIG_HRT_PPM
+#ifdef HRT_PPM_CHANNEL
 /*
  * Handle the PPM decoder state machine.
  */
@@ -526,7 +526,7 @@ error:
 	ppm_decoded_channels = 0;
 
 }
-#endif /* CONFIG_HRT_PPM */
+#endif /* HRT_PPM_CHANNEL */
 
 /*
  * Handle the compare interupt by calling the callout dispatcher
@@ -546,7 +546,7 @@ hrt_tim_isr(int irq, void *context)
 	/* ack the interrupts we just read */
 	rSR = ~status;
 
-#ifdef CONFIG_HRT_PPM
+#ifdef HRT_PPM_CHANNEL
 
 	/* was this a PPM edge? */
 	if (status & (SR_INT_PPM | SR_OVF_PPM)) {
@@ -686,7 +686,7 @@ hrt_init(void)
 	sq_init(&callout_queue);
 	hrt_tim_init();
 
-#ifdef CONFIG_HRT_PPM
+#ifdef HRT_PPM_CHANNEL
 	/* configure the PPM input pin */
 	stm32_configgpio(GPIO_PPM_IN);
 #endif
@@ -907,4 +907,4 @@ hrt_latency_update(void)
 }
 
 
-#endif /* CONFIG_HRT_TIMER */
+#endif /* HRT_TIMER */

src/drivers/stm32/tone_alarm/tone_alarm.cpp

@@ -117,10 +117,6 @@
 
 #include <systemlib/err.h>
 
-#ifndef CONFIG_HRT_TIMER
-# error This driver requires CONFIG_HRT_TIMER
-#endif
-
 /* Tone alarm configuration */
 #if   TONE_ALARM_TIMER == 2
 # define TONE_ALARM_BASE		STM32_TIM2_BASE

src/systemcmds/tests/test_hrt.c

@@ -94,7 +94,7 @@ extern uint16_t ppm_pulse_history[];
 
 int test_ppm(int argc, char *argv[])
 {
-#ifdef CONFIG_HRT_PPM
+#ifdef HRT_PPM_CHANNEL
 	unsigned i;
 
 	printf("channels: %u\n", ppm_decoded_channels);