NXP demo board config. -LH

msg/CMakeLists.txt

@@ -104,6 +104,7 @@ set(msg_files
 	landing_gear.msg
 	landing_target_innovations.msg
 	landing_target_pose.msg
+	lighting_states.msg
 	led_control.msg
 	log_message.msg
 	logger_status.msg

msg/led_control.msg

@@ -13,6 +13,7 @@ uint8 COLOR_PURPLE = 5
 uint8 COLOR_AMBER = 6
 uint8 COLOR_CYAN = 7
 uint8 COLOR_WHITE = 8
+uint8 COLOR_DIM_RED = 9
 
 # LED modes definitions
 uint8 MODE_OFF = 0 # turn LED off
@@ -27,11 +28,11 @@ uint8 MODE_FLASH = 7 # two fast blinks (on/off) with timing as in MODE_BLINK_FAS
 uint8 MAX_PRIORITY = 2 # maxium priority (minimum is 0)
 
 
-uint8 led_mask # bitmask which LED(s) to control, set to 0xff for all
+uint16 led_mask # bitmask which LED(s) to control, set to 0xff for all
 uint8 color # see COLOR_*
 uint8 mode # see MODE_*
 uint8 num_blinks # how many times to blink (number of on-off cycles if mode is one of MODE_BLINK_*) . Set to 0 for infinite
                  # in MODE_FLASH it is the number of cycles. Max number of blinks: 122 and max number of flash cycles: 20
 uint8 priority # priority: higher priority events will override current lower priority events (see MAX_PRIORITY)
 
-uint8 ORB_QUEUE_LENGTH = 8      # needs to match BOARD_MAX_LEDS
+uint8 ORB_QUEUE_LENGTH = 16      # needs to match BOARD_MAX_LEDS

msg/led_control.msg.old

@@ -0,0 +1,37 @@
+# LED control: control a single or multiple LED's.
+# These are the externally visible LED's, not the board LED's
+
+uint64 timestamp		# time since system start (microseconds)
+
+# colors
+uint8 COLOR_OFF = 0 # this is only used in the drivers
+uint8 COLOR_RED = 1
+uint8 COLOR_GREEN = 2
+uint8 COLOR_BLUE = 3
+uint8 COLOR_YELLOW = 4
+uint8 COLOR_PURPLE = 5
+uint8 COLOR_AMBER = 6
+uint8 COLOR_CYAN = 7
+uint8 COLOR_WHITE = 8
+
+# LED modes definitions
+uint8 MODE_OFF = 0 # turn LED off
+uint8 MODE_ON = 1  # turn LED on
+uint8 MODE_DISABLED = 2  # disable this priority (switch to lower priority setting)
+uint8 MODE_BLINK_SLOW = 3
+uint8 MODE_BLINK_NORMAL = 4
+uint8 MODE_BLINK_FAST = 5
+uint8 MODE_BREATHE = 6 # continuously increase & decrease brightness (solid color if driver does not support it)
+uint8 MODE_FLASH = 7 # two fast blinks (on/off) with timing as in MODE_BLINK_FAST and then off for a while
+
+uint8 MAX_PRIORITY = 2 # maxium priority (minimum is 0)
+
+
+uint8 led_mask # bitmask which LED(s) to control, set to 0xff for all
+uint8 color # see COLOR_*
+uint8 mode # see MODE_*
+uint8 num_blinks # how many times to blink (number of on-off cycles if mode is one of MODE_BLINK_*) . Set to 0 for infinite
+                 # in MODE_FLASH it is the number of cycles. Max number of blinks: 122 and max number of flash cycles: 20
+uint8 priority # priority: higher priority events will override current lower priority events (see MAX_PRIORITY)
+
+uint8 ORB_QUEUE_LENGTH = 8      # needs to match BOARD_MAX_LEDS

msg/lighting_states.msg

@@ -0,0 +1,17 @@
+# LED States for El Mandadero and NXP Buggy3
+
+uint64 timestamp
+
+uint8 IDLE     = 0 # Dim Red
+uint8 BRAKE    = 1 # Bright Red
+uint8 REVERSE  = 2 # [Top] White
+uint8 TURN     = 3 # [Top] Flashing Yellow
+uint8 HAZARD   = 4 # Flashing Yellow
+uint8 NO_STATE = 255 # No state update
+
+# LED Panel IDs
+# 0 - Right Front
+# 1 - Left Front
+# 2 - Left Rear
+# 3 - Right Rear
+uint8[10] state