mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-04-14 10:07:39 +08:00
boards: add Holybro KakuteF7
This commit is contained in:
Beat Küng
parent
098afad9e0
commit
6e833ed7a8
75
boards/holybro/kakutef7/default.cmake
Normal file
75
boards/holybro/kakutef7/default.cmake
Normal file
@ -0,0 +1,75 @@
|
||||
|
||||
px4_add_board(
|
||||
PLATFORM nuttx
|
||||
VENDOR holybro
|
||||
MODEL kakutef7
|
||||
LABEL default
|
||||
TOOLCHAIN arm-none-eabi
|
||||
ARCHITECTURE cortex-m7
|
||||
ROMFSROOT px4fmu_common
|
||||
|
||||
SERIAL_PORTS
|
||||
TEL1:/dev/ttyS0 # UART1
|
||||
TEL2:/dev/ttyS1 # UART2
|
||||
# TEL3:/dev/ttyS2 # UART3 (currently NuttX console)
|
||||
GPS1:/dev/ttyS3 # UART4
|
||||
RC:/dev/ttyS4 # UART6
|
||||
# /dev/ttyS5: UART7 (ESC telemetry)
|
||||
|
||||
DRIVERS
|
||||
barometer/bmp280
|
||||
gps
|
||||
imu/mpu6000
|
||||
magnetometer
|
||||
optical_flow/px4flow
|
||||
pwm_out_sim
|
||||
px4fmu
|
||||
rc_input
|
||||
stm32
|
||||
stm32/adc
|
||||
stm32/tone_alarm
|
||||
telemetry
|
||||
tone_alarm
|
||||
osd
|
||||
|
||||
MODULES
|
||||
attitude_estimator_q
|
||||
commander
|
||||
dataman
|
||||
#ekf2
|
||||
events
|
||||
land_detector
|
||||
load_mon
|
||||
logger
|
||||
mavlink
|
||||
mc_att_control
|
||||
mc_pos_control
|
||||
navigator
|
||||
sensors
|
||||
|
||||
SYSTEMCMDS
|
||||
bl_update
|
||||
config
|
||||
dmesg
|
||||
dumpfile
|
||||
esc_calib
|
||||
hardfault_log
|
||||
led_control
|
||||
mixer
|
||||
#motor_ramp
|
||||
motor_test
|
||||
nshterm
|
||||
param
|
||||
perf
|
||||
pwm
|
||||
reboot
|
||||
reflect
|
||||
sd_bench
|
||||
shutdown
|
||||
top
|
||||
tune_control
|
||||
topic_listener
|
||||
usb_connected
|
||||
ver
|
||||
|
||||
)
|
||||
13
boards/holybro/kakutef7/firmware.prototype
Normal file
13
boards/holybro/kakutef7/firmware.prototype
Normal file
@ -0,0 +1,13 @@
|
||||
{
|
||||
"board_id": 123,
|
||||
"magic": "KAKUTEF7",
|
||||
"description": "Firmware for the Holybro Kakute F7 board",
|
||||
"image": "",
|
||||
"build_time": 0,
|
||||
"summary": "KAKUTEF7",
|
||||
"version": "0.1",
|
||||
"image_size": 0,
|
||||
"image_maxsize": 1032192,
|
||||
"git_identity": "",
|
||||
"board_revision": 0
|
||||
}
|
||||
27
boards/holybro/kakutef7/init/rc.board_defaults
Normal file
27
boards/holybro/kakutef7/init/rc.board_defaults
Normal file
@ -0,0 +1,27 @@
|
||||
#!/bin/sh
|
||||
#
|
||||
# KakuteF7 specific board defaults
|
||||
#------------------------------------------------------------------------------
|
||||
|
||||
if param compare SYS_AUTOSTART 0
|
||||
then
|
||||
# Select the Generic 250 Racer by default
|
||||
param set SYS_AUTOSTART 4050
|
||||
set AUTOCNF yes
|
||||
fi
|
||||
|
||||
if [ $AUTOCNF = yes ]
|
||||
then
|
||||
# use the Q attitude estimator, it works w/o mag or GPS.
|
||||
param set SYS_MC_EST_GROUP 3
|
||||
param set ATT_ACC_COMP 0
|
||||
param set ATT_W_ACC 0.4000
|
||||
param set ATT_W_GYRO_BIAS 0.0000
|
||||
|
||||
param set SYS_HAS_MAG 0
|
||||
|
||||
# the startup tune is not great on a binary output buzzer, so disable it
|
||||
param set CBRK_BUZZER 782090
|
||||
fi
|
||||
|
||||
set LOGGER_BUF 30
|
||||
12
boards/holybro/kakutef7/init/rc.board_extras
Normal file
12
boards/holybro/kakutef7/init/rc.board_extras
Normal file
@ -0,0 +1,12 @@
|
||||
#!/bin/sh
|
||||
#
|
||||
# KakuteF7 specific board extras init
|
||||
#------------------------------------------------------------------------------
|
||||
|
||||
if ! param compare OSD_ATXXXX_CFG 0
|
||||
then
|
||||
atxxxx start
|
||||
fi
|
||||
|
||||
|
||||
|
||||
21
boards/holybro/kakutef7/init/rc.board_sensors
Normal file
21
boards/holybro/kakutef7/init/rc.board_sensors
Normal file
@ -0,0 +1,21 @@
|
||||
#!/bin/sh
|
||||
#
|
||||
# KakuteF7 specific board sensors init
|
||||
#------------------------------------------------------------------------------
|
||||
|
||||
|
||||
# The default IMU is an ICM20689, but there might also be an MPU6000
|
||||
if ! mpu6000 -R 12 -s start
|
||||
then
|
||||
mpu6000 -R 12 -z -T 20689 start
|
||||
fi
|
||||
|
||||
# Internal Baro
|
||||
bmp280 start
|
||||
|
||||
# Possible external compasses
|
||||
ist8310 -C -b 1 start
|
||||
ist8310 -C -b 2 start
|
||||
hmc5883 -C -T -X start
|
||||
qmc5883 -X start
|
||||
|
||||
347
boards/holybro/kakutef7/nuttx-config/include/board.h
Normal file
347
boards/holybro/kakutef7/nuttx-config/include/board.h
Normal file
@ -0,0 +1,347 @@
|
||||
/************************************************************************************
|
||||
* board.h
|
||||
*
|
||||
* Copyright (C) 2016-2018 Gregory Nutt. All rights reserved.
|
||||
* Authors: David Sidrane <david_s5@nscdg.com>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
#pragma once
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
# include <stdint.h>
|
||||
#endif
|
||||
|
||||
#include "stm32_rcc.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Pre-processor Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* Clocking *************************************************************************/
|
||||
/* The KakuteF7 board provides the following clock sources:
|
||||
*
|
||||
* 8 MHz crystal for HSE
|
||||
*
|
||||
* So we have these clock source available within the STM32
|
||||
*
|
||||
* HSI: 16 MHz RC factory-trimmed
|
||||
* HSE: 8 MHz crystal for HSE
|
||||
*/
|
||||
|
||||
#define STM32_BOARD_XTAL 8000000ul
|
||||
|
||||
#define STM32_HSI_FREQUENCY 16000000ul
|
||||
#define STM32_LSI_FREQUENCY 32000
|
||||
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
|
||||
#define STM32_LSE_FREQUENCY 0
|
||||
|
||||
/* Main PLL Configuration.
|
||||
*
|
||||
* PLL source is HSE = 8,000,000
|
||||
*
|
||||
* PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN
|
||||
* Subject to:
|
||||
*
|
||||
* 2 <= PLLM <= 63
|
||||
* 192 <= PLLN <= 432
|
||||
* 192 MHz <= PLL_VCO <= 432MHz
|
||||
*
|
||||
* SYSCLK = PLL_VCO / PLLP
|
||||
* Subject to
|
||||
*
|
||||
* PLLP = {2, 4, 6, 8}
|
||||
* SYSCLK <= 216 MHz
|
||||
*
|
||||
* USB OTG FS, SDMMC and RNG Clock = PLL_VCO / PLLQ
|
||||
* Subject to
|
||||
* The USB OTG FS requires a 48 MHz clock to work correctly. The SDMMC
|
||||
* and the random number generator need a frequency lower than or equal
|
||||
* to 48 MHz to work correctly.
|
||||
*
|
||||
* 2 <= PLLQ <= 15
|
||||
*/
|
||||
|
||||
/* Highest SYSCLK with USB OTG FS clock = 48 MHz
|
||||
*
|
||||
* PLL_VCO = (8,000,000 / 8) * 432 = 432 MHz
|
||||
* SYSCLK = 432 MHz / 2 = 216 MHz
|
||||
* USB OTG FS, SDMMC and RNG Clock = 432 MHz / 9 = 48 MHz
|
||||
*/
|
||||
|
||||
#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(8)
|
||||
#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(432)
|
||||
#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2
|
||||
#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(9)
|
||||
|
||||
#define STM32_VCO_FREQUENCY ((STM32_HSE_FREQUENCY / 8) * 432)
|
||||
#define STM32_SYSCLK_FREQUENCY (STM32_VCO_FREQUENCY / 2)
|
||||
#define STM32_OTGFS_FREQUENCY (STM32_VCO_FREQUENCY / 9)
|
||||
|
||||
/* Configure factors for PLLSAI clock */
|
||||
|
||||
#define CONFIG_STM32F7_PLLSAI 1
|
||||
#define STM32_RCC_PLLSAICFGR_PLLSAIN RCC_PLLSAICFGR_PLLSAIN(384)
|
||||
#define STM32_RCC_PLLSAICFGR_PLLSAIP RCC_PLLSAICFGR_PLLSAIP(8)
|
||||
#define STM32_RCC_PLLSAICFGR_PLLSAIQ RCC_PLLSAICFGR_PLLSAIQ(4)
|
||||
#define STM32_RCC_PLLSAICFGR_PLLSAIR RCC_PLLSAICFGR_PLLSAIR(2)
|
||||
|
||||
/* Configure Dedicated Clock Configuration Register */
|
||||
|
||||
#define STM32_RCC_DCKCFGR1_PLLI2SDIVQ RCC_DCKCFGR1_PLLI2SDIVQ(1)
|
||||
#define STM32_RCC_DCKCFGR1_PLLSAIDIVQ RCC_DCKCFGR1_PLLSAIDIVQ(1)
|
||||
#define STM32_RCC_DCKCFGR1_PLLSAIDIVR RCC_DCKCFGR1_PLLSAIDIVR(0)
|
||||
#define STM32_RCC_DCKCFGR1_SAI1SRC RCC_DCKCFGR1_SAI1SEL(0)
|
||||
#define STM32_RCC_DCKCFGR1_SAI2SRC RCC_DCKCFGR1_SAI2SEL(0)
|
||||
#define STM32_RCC_DCKCFGR1_TIMPRESRC 0
|
||||
#define STM32_RCC_DCKCFGR1_DFSDM1SRC 0
|
||||
#define STM32_RCC_DCKCFGR1_ADFSDM1SRC 0
|
||||
|
||||
|
||||
|
||||
/* Configure factors for PLLI2S clock */
|
||||
|
||||
#define CONFIG_STM32F7_PLLI2S 1
|
||||
#define STM32_RCC_PLLI2SCFGR_PLLI2SN RCC_PLLI2SCFGR_PLLI2SN(384)
|
||||
#define STM32_RCC_PLLI2SCFGR_PLLI2SP RCC_PLLI2SCFGR_PLLI2SP(2)
|
||||
#define STM32_RCC_PLLI2SCFGR_PLLI2SQ RCC_PLLI2SCFGR_PLLI2SQ(2)
|
||||
#define STM32_RCC_PLLI2SCFGR_PLLI2SR RCC_PLLI2SCFGR_PLLI2SR(2)
|
||||
|
||||
/* Configure Dedicated Clock Configuration Register 2 */
|
||||
|
||||
#define STM32_RCC_DCKCFGR2_USART1SRC RCC_DCKCFGR2_USART1SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_USART2SRC RCC_DCKCFGR2_USART2SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_UART4SRC RCC_DCKCFGR2_UART4SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_UART5SRC RCC_DCKCFGR2_UART5SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_USART6SRC RCC_DCKCFGR2_USART6SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_UART7SRC RCC_DCKCFGR2_UART7SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_UART8SRC RCC_DCKCFGR2_UART8SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_I2C1SRC RCC_DCKCFGR2_I2C1SEL_HSI
|
||||
#define STM32_RCC_DCKCFGR2_I2C2SRC RCC_DCKCFGR2_I2C2SEL_HSI
|
||||
#define STM32_RCC_DCKCFGR2_I2C3SRC RCC_DCKCFGR2_I2C3SEL_HSI
|
||||
#define STM32_RCC_DCKCFGR2_I2C4SRC RCC_DCKCFGR2_I2C4SEL_HSI
|
||||
#define STM32_RCC_DCKCFGR2_LPTIM1SRC RCC_DCKCFGR2_LPTIM1SEL_APB
|
||||
#define STM32_RCC_DCKCFGR2_CECSRC RCC_DCKCFGR2_CECSEL_HSI
|
||||
#define STM32_RCC_DCKCFGR2_CK48MSRC RCC_DCKCFGR2_CK48MSEL_PLL
|
||||
#define STM32_RCC_DCKCFGR2_SDMMCSRC RCC_DCKCFGR2_SDMMCSEL_48MHZ
|
||||
#define STM32_RCC_DCKCFGR2_SDMMC2SRC RCC_DCKCFGR2_SDMMC2SEL_48MHZ
|
||||
#define STM32_RCC_DCKCFGR2_DSISRC RCC_DCKCFGR2_DSISEL_PHY
|
||||
|
||||
|
||||
/* Several prescalers allow the configuration of the two AHB buses, the
|
||||
* high-speed APB (APB2) and the low-speed APB (APB1) domains. The maximum
|
||||
* frequency of the two AHB buses is 216 MHz while the maximum frequency of
|
||||
* the high-speed APB domains is 108 MHz. The maximum allowed frequency of
|
||||
* the low-speed APB domain is 54 MHz.
|
||||
*/
|
||||
|
||||
/* AHB clock (HCLK) is SYSCLK (216 MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
|
||||
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
|
||||
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */
|
||||
|
||||
/* APB1 clock (PCLK1) is HCLK/4 (54 MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */
|
||||
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4)
|
||||
|
||||
/* Timers driven from APB1 will be twice PCLK1 */
|
||||
|
||||
#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
|
||||
/* APB2 clock (PCLK2) is HCLK/2 (108MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */
|
||||
#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2)
|
||||
|
||||
/* Timers driven from APB2 will be twice PCLK2 */
|
||||
|
||||
#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
|
||||
|
||||
/* FLASH wait states
|
||||
*
|
||||
* --------- ---------- -----------
|
||||
* VDD MAX SYSCLK WAIT STATES
|
||||
* --------- ---------- -----------
|
||||
* 1.7-2.1 V 180 MHz 8
|
||||
* 2.1-2.4 V 216 MHz 9
|
||||
* 2.4-2.7 V 216 MHz 8
|
||||
* 2.7-3.6 V 216 MHz 7
|
||||
* --------- ---------- -----------
|
||||
*/
|
||||
|
||||
#define BOARD_FLASH_WAITSTATES 7
|
||||
|
||||
/* LED definitions ******************************************************************/
|
||||
|
||||
/* LED index values for use with board_userled() */
|
||||
|
||||
#define BOARD_LED1 0
|
||||
#define BOARD_NLEDS 1
|
||||
|
||||
#define BOARD_LED_BLUE BOARD_LED1
|
||||
|
||||
/* LED bits for use with board_userled_all() */
|
||||
|
||||
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
||||
|
||||
/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
|
||||
* include/board.h and src/stm32_leds.c. The LEDs are used to encode OS-related
|
||||
* events as follows:
|
||||
*
|
||||
*
|
||||
* SYMBOL Meaning LED state
|
||||
* Red Green Blue
|
||||
* ---------------------- -------------------------- ------ ------ ----*/
|
||||
|
||||
#define LED_STARTED 0 /* NuttX has been started OFF OFF OFF */
|
||||
#define LED_HEAPALLOCATE 1 /* Heap has been allocated OFF OFF ON */
|
||||
#define LED_IRQSENABLED 2 /* Interrupts enabled OFF ON OFF */
|
||||
#define LED_STACKCREATED 3 /* Idle stack created OFF ON ON */
|
||||
#define LED_INIRQ 4 /* In an interrupt N/C N/C GLOW */
|
||||
#define LED_SIGNAL 5 /* In a signal handler N/C GLOW N/C */
|
||||
#define LED_ASSERTION 6 /* An assertion failed GLOW N/C GLOW */
|
||||
#define LED_PANIC 7 /* The system has crashed Blink OFF N/C */
|
||||
#define LED_IDLE 8 /* MCU is is sleep mode ON OFF OFF */
|
||||
|
||||
/* Alternate function pin selections (see stm32f74xx75xx_pinmap.h) ******************************/
|
||||
|
||||
#define GPIO_USART1_RX GPIO_USART1_RX_1 /* PA10 */
|
||||
#define GPIO_USART1_TX GPIO_USART1_TX_1 /* PA9 */
|
||||
|
||||
#define GPIO_USART2_RX GPIO_USART2_RX_2 /* PD6 */
|
||||
#define GPIO_USART2_TX GPIO_USART2_TX_2 /* PD5 */
|
||||
|
||||
#define GPIO_USART3_RX GPIO_USART3_RX_1 /* PB11 */
|
||||
#define GPIO_USART3_TX GPIO_USART3_TX_1 /* PB10 */
|
||||
|
||||
#define GPIO_UART4_RX GPIO_UART4_RX_1 /* PA1 */
|
||||
#define GPIO_UART4_TX GPIO_UART4_TX_1 /* PA0 */
|
||||
|
||||
#define GPIO_USART6_RX GPIO_USART6_RX_1 /* PC7 */
|
||||
#define GPIO_USART6_TX GPIO_USART6_TX_1 /* PC6 */
|
||||
|
||||
#define GPIO_UART7_RX GPIO_UART7_RX_1 /* PE7 */
|
||||
#define GPIO_UART7_TX GPIO_UART7_TX_1 /* PE8 */
|
||||
|
||||
/* UART RX DMA configurations */
|
||||
|
||||
#define DMAMAP_USART1_RX DMAMAP_USART1_RX_2
|
||||
#define DMAMAP_USART6_RX DMAMAP_USART6_RX_2
|
||||
|
||||
/* SPI
|
||||
* SPI1 SD Card
|
||||
* SPI2 is OSD AT7456E
|
||||
* SPI4 is IMU
|
||||
*/
|
||||
|
||||
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 /* PA6 */
|
||||
#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 /* PA7 */
|
||||
#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 /* PA5 */
|
||||
|
||||
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 /* PB14 */
|
||||
#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 /* PB15 */
|
||||
#define GPIO_SPI2_SCK GPIO_SPI2_SCK_3 /* PB13 */
|
||||
|
||||
#define GPIO_SPI4_MISO GPIO_SPI4_MISO_1 /* PE5 */
|
||||
#define GPIO_SPI4_MOSI GPIO_SPI4_MOSI_1 /* PE6 */
|
||||
#define GPIO_SPI4_SCK GPIO_SPI4_SCK_1 /* PE2 */
|
||||
|
||||
/* I2C
|
||||
*/
|
||||
|
||||
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1 /* PB6 */
|
||||
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1 /* PB7 */
|
||||
|
||||
#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN6)
|
||||
#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT | GPIO_OPENDRAIN |GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN7)
|
||||
|
||||
/* USB
|
||||
*
|
||||
* OTG_FS_DM PA11
|
||||
* OTG_FS_DP PA12
|
||||
* VBUS PA8
|
||||
*/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Data
|
||||
************************************************************************************/
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
#define EXTERN extern "C"
|
||||
extern "C"
|
||||
{
|
||||
#else
|
||||
#define EXTERN extern
|
||||
#endif
|
||||
|
||||
/************************************************************************************
|
||||
* Public Function Prototypes
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_boardinitialize
|
||||
*
|
||||
* Description:
|
||||
* All STM32 architectures must provide the following entry point. This entry point
|
||||
* is called early in the initialization -- after all memory has been configured
|
||||
* and mapped but before any devices have been initialized.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
void stm32_boardinitialize(void);
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
219
boards/holybro/kakutef7/nuttx-config/nsh/defconfig
Normal file
219
boards/holybro/kakutef7/nuttx-config/nsh/defconfig
Normal file
@ -0,0 +1,219 @@
|
||||
# CONFIG_DISABLE_OS_API is not set
|
||||
# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set
|
||||
# CONFIG_MMCSD_HAVE_CARDDETECT is not set
|
||||
# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set
|
||||
# CONFIG_MMCSD_MMCSUPPORT is not set
|
||||
# CONFIG_NSH_DISABLEBG is not set
|
||||
# CONFIG_NSH_DISABLESCRIPT is not set
|
||||
# CONFIG_NSH_DISABLE_DF is not set
|
||||
# CONFIG_NSH_DISABLE_EXEC is not set
|
||||
# CONFIG_NSH_DISABLE_EXIT is not set
|
||||
# CONFIG_NSH_DISABLE_GET is not set
|
||||
# CONFIG_NSH_DISABLE_ITEF is not set
|
||||
# CONFIG_NSH_DISABLE_LOOPS is not set
|
||||
# CONFIG_NSH_DISABLE_SEMICOLON is not set
|
||||
# CONFIG_NSH_DISABLE_TIME is not set
|
||||
# CONFIG_SPI_CALLBACK is not set
|
||||
CONFIG_ARCH="arm"
|
||||
CONFIG_ARCH_BOARD_CUSTOM_DIR="../nuttx-config"
|
||||
CONFIG_ARCH_BOARD_CUSTOM_NAME="px4"
|
||||
CONFIG_ARCH_CHIP_STM32F745VG=y
|
||||
CONFIG_ARCH_CHIP_STM32F7=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=750
|
||||
CONFIG_ARCH_MATH_H=y
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARMV7M_BASEPRI_WAR=y
|
||||
CONFIG_ARMV7M_DCACHE=y
|
||||
CONFIG_ARMV7M_DTCM=y
|
||||
CONFIG_ARMV7M_ICACHE=y
|
||||
CONFIG_ARMV7M_MEMCPY=y
|
||||
CONFIG_ARMV7M_USEBASEPRI=y
|
||||
CONFIG_BOARDCTL_RESET=y
|
||||
CONFIG_BOARD_CRASHDUMP=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=22114
|
||||
CONFIG_BOARD_RESET_ON_ASSERT=2
|
||||
CONFIG_BUILTIN=y
|
||||
CONFIG_C99_BOOL8=y
|
||||
CONFIG_CDCACM=y
|
||||
CONFIG_CDCACM_PRODUCTID=0x0016
|
||||
CONFIG_CDCACM_PRODUCTSTR="PX4 KakuteF7"
|
||||
CONFIG_CDCACM_RXBUFSIZE=600
|
||||
CONFIG_CDCACM_TXBUFSIZE=12000
|
||||
CONFIG_CDCACM_VENDORID=0x26ac
|
||||
CONFIG_CDCACM_VENDORSTR="Holybro"
|
||||
CONFIG_CLOCK_MONOTONIC=y
|
||||
CONFIG_DEBUG_FULLOPT=y
|
||||
CONFIG_DEBUG_HARDFAULT_ALERT=y
|
||||
CONFIG_DEBUG_SYMBOLS=y
|
||||
CONFIG_DEFAULT_SMALL=y
|
||||
CONFIG_DEV_FIFO_SIZE=0
|
||||
CONFIG_DEV_PIPE_MAXSIZE=1024
|
||||
CONFIG_DEV_PIPE_SIZE=70
|
||||
CONFIG_FAT_DMAMEMORY=y
|
||||
CONFIG_FAT_LCNAMES=y
|
||||
CONFIG_FAT_LFN=y
|
||||
CONFIG_FAT_LFN_ALIAS_HASH=y
|
||||
CONFIG_FDCLONE_STDIO=y
|
||||
CONFIG_FS_BINFS=y
|
||||
CONFIG_FS_CROMFS=y
|
||||
CONFIG_FS_FAT=y
|
||||
CONFIG_FS_FATTIME=y
|
||||
CONFIG_FS_PROCFS=y
|
||||
CONFIG_FS_PROCFS_EXCLUDE_BLOCKS=y
|
||||
CONFIG_FS_PROCFS_EXCLUDE_MOUNT=y
|
||||
CONFIG_FS_PROCFS_EXCLUDE_MOUNTS=y
|
||||
CONFIG_FS_PROCFS_EXCLUDE_PARTITIONS=y
|
||||
CONFIG_FS_PROCFS_EXCLUDE_USAGE=y
|
||||
CONFIG_FS_PROCFS_REGISTER=y
|
||||
CONFIG_FS_ROMFS=y
|
||||
CONFIG_GRAN=y
|
||||
CONFIG_GRAN_INTR=y
|
||||
CONFIG_HAVE_CXX=y
|
||||
CONFIG_HAVE_CXXINITIALIZE=y
|
||||
CONFIG_I2C=y
|
||||
CONFIG_I2C_RESET=y
|
||||
CONFIG_IDLETHREAD_STACKSIZE=750
|
||||
CONFIG_LIBC_FLOATINGPOINT=y
|
||||
CONFIG_LIBC_LONG_LONG=y
|
||||
CONFIG_LIBC_STRERROR=y
|
||||
CONFIG_MAX_TASKS=64
|
||||
CONFIG_MAX_WDOGPARMS=2
|
||||
CONFIG_MEMSET_64BIT=y
|
||||
CONFIG_MEMSET_OPTSPEED=y
|
||||
CONFIG_MMCSD=y
|
||||
CONFIG_MMCSD_MULTIBLOCK_DISABLE=y
|
||||
CONFIG_MM_REGIONS=3
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_BYTE_WRITE=y
|
||||
CONFIG_MTD_PARTITION=y
|
||||
CONFIG_MTD_RAMTRON=y
|
||||
CONFIG_NFILE_DESCRIPTORS=54
|
||||
CONFIG_NFILE_STREAMS=8
|
||||
CONFIG_NSH_ARCHINIT=y
|
||||
CONFIG_NSH_ARCHROMFS=y
|
||||
CONFIG_NSH_ARGCAT=y
|
||||
CONFIG_NSH_BUILTIN_APPS=y
|
||||
CONFIG_NSH_CMDPARMS=y
|
||||
CONFIG_NSH_CROMFSETC=y
|
||||
CONFIG_NSH_DISABLE_IFCONFIG=y
|
||||
CONFIG_NSH_DISABLE_IFUPDOWN=y
|
||||
CONFIG_NSH_DISABLE_MB=y
|
||||
CONFIG_NSH_DISABLE_MH=y
|
||||
CONFIG_NSH_DISABLE_PSSTACKUSAGE=y
|
||||
CONFIG_NSH_DISABLE_TELNETD=y
|
||||
CONFIG_NSH_LINELEN=128
|
||||
CONFIG_NSH_MAXARGUMENTS=12
|
||||
CONFIG_NSH_MMCSDSPIPORTNO=1
|
||||
CONFIG_NSH_NESTDEPTH=8
|
||||
CONFIG_NSH_QUOTE=y
|
||||
CONFIG_NSH_ROMFSETC=y
|
||||
CONFIG_NSH_ROMFSSECTSIZE=128
|
||||
CONFIG_NSH_STRERROR=y
|
||||
CONFIG_NSH_VARS=y
|
||||
CONFIG_NXFONTS_DISABLE_16BPP=y
|
||||
CONFIG_NXFONTS_DISABLE_1BPP=y
|
||||
CONFIG_NXFONTS_DISABLE_24BPP=y
|
||||
CONFIG_NXFONTS_DISABLE_2BPP=y
|
||||
CONFIG_NXFONTS_DISABLE_32BPP=y
|
||||
CONFIG_NXFONTS_DISABLE_4BPP=y
|
||||
CONFIG_NXFONTS_DISABLE_8BPP=y
|
||||
CONFIG_PIPES=y
|
||||
CONFIG_PREALLOC_MQ_MSGS=4
|
||||
CONFIG_PREALLOC_TIMERS=50
|
||||
CONFIG_PREALLOC_WDOGS=50
|
||||
CONFIG_PRIORITY_INHERITANCE=y
|
||||
CONFIG_PTHREAD_MUTEX_ROBUST=y
|
||||
CONFIG_PTHREAD_STACK_MIN=512
|
||||
CONFIG_RAMTRON_SETSPEED=y
|
||||
CONFIG_RAMTRON_WRITEWAIT=y
|
||||
CONFIG_RAM_SIZE=245760
|
||||
CONFIG_RAM_START=0x20010000
|
||||
CONFIG_RAW_BINARY=y
|
||||
CONFIG_RTC_DATETIME=y
|
||||
CONFIG_SCHED_ATEXIT=y
|
||||
CONFIG_SCHED_HPWORK=y
|
||||
CONFIG_SCHED_HPWORKPRIORITY=249
|
||||
CONFIG_SCHED_HPWORKSTACKSIZE=1800
|
||||
CONFIG_SCHED_INSTRUMENTATION=y
|
||||
CONFIG_SCHED_LPWORK=y
|
||||
CONFIG_SCHED_LPWORKPRIORITY=50
|
||||
CONFIG_SCHED_LPWORKSTACKSIZE=1800
|
||||
CONFIG_SCHED_WAITPID=y
|
||||
CONFIG_SDCLONE_DISABLE=y
|
||||
CONFIG_SEM_NNESTPRIO=8
|
||||
CONFIG_SEM_PREALLOCHOLDERS=0
|
||||
CONFIG_SERIAL_TERMIOS=y
|
||||
CONFIG_SIG_DEFAULT=y
|
||||
CONFIG_SIG_SIGALRM_ACTION=y
|
||||
CONFIG_SIG_SIGUSR1_ACTION=y
|
||||
CONFIG_SIG_SIGUSR2_ACTION=y
|
||||
CONFIG_SIG_SIGWORK=4
|
||||
CONFIG_STACK_COLORATION=y
|
||||
CONFIG_START_DAY=30
|
||||
CONFIG_START_MONTH=11
|
||||
CONFIG_STDIO_BUFFER_SIZE=32
|
||||
CONFIG_STM32F7_ADC1=y
|
||||
CONFIG_STM32F7_BBSRAM=y
|
||||
CONFIG_STM32F7_BBSRAM_FILES=5
|
||||
CONFIG_STM32F7_BKPSRAM=y
|
||||
CONFIG_STM32F7_DMA1=y
|
||||
CONFIG_STM32F7_I2C1=y
|
||||
CONFIG_STM32F7_I2C_DYNTIMEO=y
|
||||
CONFIG_STM32F7_I2C_DYNTIMEO_STARTSTOP=10
|
||||
CONFIG_STM32F7_OTGFS=y
|
||||
CONFIG_STM32F7_PWR=y
|
||||
CONFIG_STM32F7_RTC=y
|
||||
CONFIG_STM32F7_RTC_HSECLOCK=y
|
||||
CONFIG_STM32F7_RTC_MAGIC_REG=1
|
||||
CONFIG_STM32F7_SAVE_CRASHDUMP=y
|
||||
CONFIG_STM32F7_SERIALBRK_BSDCOMPAT=y
|
||||
CONFIG_STM32F7_SERIAL_DISABLE_REORDERING=y
|
||||
CONFIG_STM32F7_SPI1=y
|
||||
CONFIG_STM32F7_SPI2=y
|
||||
CONFIG_STM32F7_SPI4=y
|
||||
CONFIG_STM32F7_TIM1=y
|
||||
CONFIG_STM32F7_TIM3=y
|
||||
CONFIG_STM32F7_TIM5=y
|
||||
CONFIG_STM32F7_TIM8=y
|
||||
CONFIG_STM32F7_UART4=y
|
||||
CONFIG_STM32F7_UART7=y
|
||||
CONFIG_STM32F7_USART1=y
|
||||
CONFIG_STM32F7_USART2=y
|
||||
CONFIG_STM32F7_USART3=y
|
||||
CONFIG_STM32F7_USART6=y
|
||||
CONFIG_STM32F7_USART_BREAKS=y
|
||||
CONFIG_STM32F7_USART_INVERT=y
|
||||
CONFIG_STM32F7_USART_SINGLEWIRE=y
|
||||
CONFIG_STM32F7_USART_SWAP=y
|
||||
CONFIG_STM32F7_WWDG=y
|
||||
CONFIG_SYSTEM_CDCACM=y
|
||||
CONFIG_SYSTEM_NSH=y
|
||||
CONFIG_TASK_NAME_SIZE=24
|
||||
CONFIG_TIME_EXTENDED=y
|
||||
CONFIG_UART4_BAUD=57600
|
||||
CONFIG_UART4_RXBUFSIZE=600
|
||||
CONFIG_UART4_RXDMA=y
|
||||
CONFIG_UART4_TXBUFSIZE=1500
|
||||
CONFIG_UART7_BAUD=57600
|
||||
CONFIG_UART7_RXBUFSIZE=600
|
||||
CONFIG_UART7_TXBUFSIZE=1500
|
||||
CONFIG_USART1_BAUD=57600
|
||||
CONFIG_USART1_RXBUFSIZE=600
|
||||
CONFIG_USART1_TXBUFSIZE=1500
|
||||
CONFIG_USART2_BAUD=57600
|
||||
CONFIG_USART2_RXBUFSIZE=600
|
||||
CONFIG_USART2_RXDMA=y
|
||||
CONFIG_USART2_TXBUFSIZE=2500
|
||||
CONFIG_USART3_BAUD=57600
|
||||
CONFIG_USART3_RXBUFSIZE=600
|
||||
CONFIG_USART3_SERIAL_CONSOLE=y
|
||||
CONFIG_USART3_TXBUFSIZE=1500
|
||||
CONFIG_USART6_BAUD=57600
|
||||
CONFIG_USART6_RXBUFSIZE=600
|
||||
CONFIG_USART6_TXBUFSIZE=1500
|
||||
CONFIG_USBDEV=y
|
||||
CONFIG_USBDEV_BUSPOWERED=y
|
||||
CONFIG_USBDEV_MAXPOWER=500
|
||||
CONFIG_USEC_PER_TICK=1000
|
||||
CONFIG_USERMAIN_STACKSIZE=2624
|
||||
CONFIG_USER_ENTRYPOINT="nsh_main"
|
||||
184
boards/holybro/kakutef7/nuttx-config/scripts/script.ld
Normal file
184
boards/holybro/kakutef7/nuttx-config/scripts/script.ld
Normal file
@ -0,0 +1,184 @@
|
||||
/****************************************************************************
|
||||
* scripts/script.ld
|
||||
*
|
||||
* Copyright (C) 2016 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/* The STM32F745VGT6 has 1024 KiB of main FLASH memory. This FLASH memory
|
||||
* can be accessed from either the AXIM interface at address 0x0800:0000 or
|
||||
* from the ITCM interface at address 0x0020:0000.
|
||||
*
|
||||
* Additional information, including the option bytes, is available at at
|
||||
* FLASH at address 0x1ff0:0000 (AXIM) or 0x0010:0000 (ITCM).
|
||||
*
|
||||
* In the STM32F745VGT6, two different boot spaces can be selected through
|
||||
* the BOOT pin and the boot base address programmed in the BOOT_ADD0 and
|
||||
* BOOT_ADD1 option bytes:
|
||||
*
|
||||
* 1) BOOT=0: Boot address defined by user option byte BOOT_ADD0[15:0].
|
||||
* ST programmed value: Flash on ITCM at 0x0020:0000
|
||||
* 2) BOOT=1: Boot address defined by user option byte BOOT_ADD1[15:0].
|
||||
* ST programmed value: System bootloader at 0x0010:0000
|
||||
*
|
||||
* NuttX does not modify these option byes. On the unmodified NUCLEO-144
|
||||
* board, the BOOT0 pin is at ground so by default, the STM32F745VGT6 will
|
||||
* boot from address 0x0020:0000 in ITCM FLASH.
|
||||
*
|
||||
* The STM32F745VGT6 also has 320 KiB of data SRAM (in addition to ITCM SRAM).
|
||||
* SRAM is split up into three blocks:
|
||||
*
|
||||
* 1) 64 KiB of DTCM SRM beginning at address 0x2000:0000
|
||||
* 2) 240 KiB of SRAM1 beginning at address 0x2001:0000
|
||||
* 3) 16 KiB of SRAM2 beginning at address 0x2004:c000
|
||||
*
|
||||
* When booting from FLASH, FLASH memory is aliased to address 0x0000:0000
|
||||
* where the code expects to begin execution by jumping to the entry point in
|
||||
* the 0x0800:0000 address range.
|
||||
*
|
||||
* Bootloader reserves the first 32K bank.
|
||||
* The next 2 32K sectors are reserved for parameters.
|
||||
*
|
||||
*/
|
||||
|
||||
MEMORY
|
||||
{
|
||||
itcm (rwx) : ORIGIN = 0x00208000, LENGTH = 2016K
|
||||
flash (rx) : ORIGIN = 0x08018000, LENGTH = 928K
|
||||
dtcm (rwx) : ORIGIN = 0x20000000, LENGTH = 128K
|
||||
sram1 (rwx) : ORIGIN = 0x20020000, LENGTH = 368K
|
||||
sram2 (rwx) : ORIGIN = 0x2007c000, LENGTH = 16K
|
||||
}
|
||||
|
||||
OUTPUT_ARCH(arm)
|
||||
EXTERN(_vectors)
|
||||
ENTRY(_stext)
|
||||
|
||||
/*
|
||||
* Ensure that abort() is present in the final object. The exception handling
|
||||
* code pulled in by libgcc.a requires it (and that code cannot be easily avoided).
|
||||
*/
|
||||
EXTERN(abort)
|
||||
EXTERN(_bootdelay_signature)
|
||||
|
||||
SECTIONS
|
||||
{
|
||||
.text : {
|
||||
_stext = ABSOLUTE(.);
|
||||
*(.vectors)
|
||||
. = ALIGN(32);
|
||||
/*
|
||||
This signature provides the bootloader with a way to delay booting
|
||||
*/
|
||||
_bootdelay_signature = ABSOLUTE(.);
|
||||
FILL(0xffecc2925d7d05c5)
|
||||
. += 8;
|
||||
*(.text .text.*)
|
||||
*(.fixup)
|
||||
*(.gnu.warning)
|
||||
*(.rodata .rodata.*)
|
||||
*(.gnu.linkonce.t.*)
|
||||
*(.glue_7)
|
||||
*(.glue_7t)
|
||||
*(.got)
|
||||
*(.gcc_except_table)
|
||||
*(.gnu.linkonce.r.*)
|
||||
_etext = ABSOLUTE(.);
|
||||
|
||||
/*
|
||||
* This is a hack to make the newlib libm __errno() call
|
||||
* use the NuttX get_errno_ptr() function.
|
||||
*/
|
||||
__errno = get_errno_ptr;
|
||||
} > flash
|
||||
|
||||
/*
|
||||
* Init functions (static constructors and the like)
|
||||
*/
|
||||
.init_section : {
|
||||
_sinit = ABSOLUTE(.);
|
||||
KEEP(*(.init_array .init_array.*))
|
||||
_einit = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
/*
|
||||
* Construction data for parameters.
|
||||
*/
|
||||
__param ALIGN(4): {
|
||||
__param_start = ABSOLUTE(.);
|
||||
KEEP(*(__param*))
|
||||
__param_end = ABSOLUTE(.);
|
||||
} > flash
|
||||
|
||||
.ARM.extab : {
|
||||
*(.ARM.extab*)
|
||||
} > flash
|
||||
|
||||
__exidx_start = ABSOLUTE(.);
|
||||
.ARM.exidx : {
|
||||
*(.ARM.exidx*)
|
||||
} > flash
|
||||
__exidx_end = ABSOLUTE(.);
|
||||
|
||||
_eronly = ABSOLUTE(.);
|
||||
|
||||
.data : {
|
||||
_sdata = ABSOLUTE(.);
|
||||
*(.data .data.*)
|
||||
*(.gnu.linkonce.d.*)
|
||||
CONSTRUCTORS
|
||||
_edata = ABSOLUTE(.);
|
||||
} > sram1 AT > flash
|
||||
|
||||
.bss : {
|
||||
_sbss = ABSOLUTE(.);
|
||||
*(.bss .bss.*)
|
||||
*(.gnu.linkonce.b.*)
|
||||
*(COMMON)
|
||||
. = ALIGN(4);
|
||||
_ebss = ABSOLUTE(.);
|
||||
} > sram1
|
||||
|
||||
/* Stabs debugging sections. */
|
||||
.stab 0 : { *(.stab) }
|
||||
.stabstr 0 : { *(.stabstr) }
|
||||
.stab.excl 0 : { *(.stab.excl) }
|
||||
.stab.exclstr 0 : { *(.stab.exclstr) }
|
||||
.stab.index 0 : { *(.stab.index) }
|
||||
.stab.indexstr 0 : { *(.stab.indexstr) }
|
||||
.comment 0 : { *(.comment) }
|
||||
.debug_abbrev 0 : { *(.debug_abbrev) }
|
||||
.debug_info 0 : { *(.debug_info) }
|
||||
.debug_line 0 : { *(.debug_line) }
|
||||
.debug_pubnames 0 : { *(.debug_pubnames) }
|
||||
.debug_aranges 0 : { *(.debug_aranges) }
|
||||
}
|
||||
48
boards/holybro/kakutef7/src/CMakeLists.txt
Normal file
48
boards/holybro/kakutef7/src/CMakeLists.txt
Normal file
@ -0,0 +1,48 @@
|
||||
############################################################################
|
||||
#
|
||||
# Copyright (c) 2019 PX4 Development Team. All rights reserved.
|
||||
#
|
||||
# Redistribution and use in source and binary forms, with or without
|
||||
# modification, are permitted provided that the following conditions
|
||||
# are met:
|
||||
#
|
||||
# 1. Redistributions of source code must retain the above copyright
|
||||
# notice, this list of conditions and the following disclaimer.
|
||||
# 2. Redistributions in binary form must reproduce the above copyright
|
||||
# notice, this list of conditions and the following disclaimer in
|
||||
# the documentation and/or other materials provided with the
|
||||
# distribution.
|
||||
# 3. Neither the name PX4 nor the names of its contributors may be
|
||||
# used to endorse or promote products derived from this software
|
||||
# without specific prior written permission.
|
||||
#
|
||||
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
# POSSIBILITY OF SUCH DAMAGE.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
add_library(drivers_board
|
||||
init.c
|
||||
led.c
|
||||
spi.cpp
|
||||
timer_config.c
|
||||
usb.c
|
||||
)
|
||||
|
||||
target_link_libraries(drivers_board
|
||||
PRIVATE
|
||||
drivers__led # drv_led_start
|
||||
nuttx_arch # sdio
|
||||
nuttx_drivers # sdio
|
||||
px4_layer
|
||||
)
|
||||
290
boards/holybro/kakutef7/src/board_config.h
Normal file
290
boards/holybro/kakutef7/src/board_config.h
Normal file
@ -0,0 +1,290 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (c) 2019 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/**
|
||||
* @file board_config.h
|
||||
*
|
||||
* KakuteF7 internal definitions
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
/****************************************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************************************/
|
||||
|
||||
#include <px4_config.h>
|
||||
#include <nuttx/compiler.h>
|
||||
#include <stdint.h>
|
||||
|
||||
#include <stm32_gpio.h>
|
||||
|
||||
/****************************************************************************************************
|
||||
* Definitions
|
||||
****************************************************************************************************/
|
||||
|
||||
/* GPIOs ***********************************************************************************/
|
||||
|
||||
/* LEDs are driven with push open drain to support Anode to 5V or 3.3V */
|
||||
|
||||
#define GPIO_nLED_BLUE /* PA2 */ (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN2)
|
||||
|
||||
#define BOARD_HAS_CONTROL_STATUS_LEDS 1
|
||||
#define BOARD_ARMED_STATE_LED LED_BLUE
|
||||
|
||||
#define FLASH_BASED_PARAMS
|
||||
|
||||
/* SPI busses
|
||||
*/
|
||||
#define PX4_SPI_BUS_SD_CARD 1
|
||||
#define PX4_SPI_BUS_OSD 2
|
||||
#define PX4_SPI_BUS_SENSORS 4
|
||||
|
||||
/* Define the Chip Selects, Data Ready and Control signals per SPI bus */
|
||||
|
||||
#define GPIO_SPI1_CS1_SD_CARD /* PA4 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
|
||||
|
||||
#define PX4_SD_CARD_BUS_CS_GPIO {GPIO_SPI1_CS1_SD_CARD}
|
||||
|
||||
#define GPIO_SPI2_CS1_OSD /* PB12 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN12)
|
||||
#define PX4_SPIDEV_OSD 1
|
||||
|
||||
#define PX4_OSD_BUS_CS_GPIO {GPIO_SPI2_CS1_OSD}
|
||||
|
||||
/* SPI 4 CS (SPI4_SS) */
|
||||
|
||||
#define GPIO_SPI4_CS1_ICM20689 /* PE4 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN4)
|
||||
|
||||
|
||||
/* Define the SPI4 Data Ready interrupts */
|
||||
|
||||
#define GPIO_SPI4_DRDY1_ICM20689 /* PE1 */ (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTE|GPIO_PIN1)
|
||||
|
||||
|
||||
#define PX4_SPIDEV_MPU PX4_MK_SPI_SEL(PX4_SPI_BUS_SENSORS,0)
|
||||
#define PX4_SPIDEV_ICM_20689 PX4_MK_SPI_SEL(PX4_SPI_BUS_SENSORS,0)
|
||||
#define PX4_SENSOR_BUS_CS_GPIO {GPIO_SPI4_CS1_ICM20689}
|
||||
|
||||
/* I2C busses */
|
||||
|
||||
#define PX4_I2C_BUS_EXPANSION 1
|
||||
#define PX4_I2C_BUS_LED PX4_I2C_BUS_EXPANSION
|
||||
|
||||
#define BOARD_NUMBER_I2C_BUSES 1
|
||||
#define BOARD_I2C_BUS_CLOCK_INIT {100000}
|
||||
|
||||
#define PX4_I2C_OBDEV_BMP280 0x76
|
||||
|
||||
/*
|
||||
* ADC channels
|
||||
*
|
||||
* These are the channel numbers of the ADCs of the microcontroller that
|
||||
* can be used by the Px4 Firmware in the adc driver
|
||||
*/
|
||||
|
||||
/* ADC defines to be used in sensors.cpp to read from a particular channel */
|
||||
#define ADC1_CH(n) (n)
|
||||
#define ADC1_GPIO(n) GPIO_ADC1_IN##n
|
||||
|
||||
/* Define GPIO pins used as ADC N.B. Channel numbers must match below */
|
||||
#define PX4_ADC_GPIO \
|
||||
/* PC2 */ ADC1_GPIO(12), \
|
||||
/* PC3 */ ADC1_GPIO(13), \
|
||||
/* PC5 */ ADC1_GPIO(15)
|
||||
|
||||
/* Define Channel numbers must match above GPIO pin IN(n)*/
|
||||
#define ADC_RSSI_IN_CHANNEL /* PC5 */ ADC1_CH(15)
|
||||
#define ADC_BATTERY_VOLTAGE_CHANNEL /* PC3 */ ADC1_CH(13)
|
||||
#define ADC_BATTERY_CURRENT_CHANNEL /* PC2 */ ADC1_CH(12)
|
||||
|
||||
#define ADC_CHANNELS \
|
||||
((1 << ADC_BATTERY_VOLTAGE_CHANNEL) | \
|
||||
(1 << ADC_BATTERY_CURRENT_CHANNEL) | \
|
||||
(1 << ADC_RSSI_IN_CHANNEL))
|
||||
|
||||
/* Define Battery 1 Voltage Divider and A per V
|
||||
*/
|
||||
#define BOARD_BATTERY1_V_DIV (10.9f)
|
||||
#define BOARD_BATTERY1_A_PER_V (17.f)
|
||||
|
||||
/* PWM
|
||||
*/
|
||||
#define GPIO_TIM5_CH4OUT /* PA3 T5C4 PWM6 */ GPIO_TIM5_CH4OUT_1
|
||||
#define GPIO_TIM8_CH4OUT /* PC9 T8C4 PWM5 */ GPIO_TIM8_CH4OUT_1
|
||||
#define GPIO_TIM1_CH2OUT /* PE11 T1C2 PWM4 */ GPIO_TIM1_CH2OUT_2
|
||||
#define GPIO_TIM1_CH1OUT /* PE9 T1C1 PWM3 */ GPIO_TIM1_CH1OUT_2
|
||||
#define GPIO_TIM3_CH4OUT /* PB1 T3C4 PWM2 */ GPIO_TIM3_CH4OUT_1
|
||||
#define GPIO_TIM3_CH3OUT /* PB0 T3C3 PWM1 */ GPIO_TIM3_CH3OUT_1
|
||||
|
||||
#define DIRECT_PWM_OUTPUT_CHANNELS 6
|
||||
|
||||
#define GPIO_TIM5_CH4IN /* PA3 T5C4 PWM6 */ GPIO_TIM5_CH4IN_1
|
||||
#define GPIO_TIM8_CH4IN /* PC9 T8C4 PWM5 */ GPIO_TIM8_CH4IN_1
|
||||
#define GPIO_TIM1_CH2IN /* PE11 T1C2 PWM4 */ GPIO_TIM1_CH2IN_2
|
||||
#define GPIO_TIM1_CH1IN /* PE9 T1C1 PWM3 */ GPIO_TIM1_CH1IN_2
|
||||
#define GPIO_TIM3_CH4IN /* PB1 T3C4 PWM2 */ GPIO_TIM3_CH4IN_1
|
||||
#define GPIO_TIM3_CH3IN /* PB0 T3C3 PWM1 */ GPIO_TIM3_CH3IN_1
|
||||
|
||||
#define DIRECT_INPUT_TIMER_CHANNELS 6
|
||||
|
||||
/* User GPIOs
|
||||
*/
|
||||
|
||||
#define _MK_GPIO_INPUT(def) (((def) & (GPIO_PORT_MASK | GPIO_PIN_MASK)) | (GPIO_INPUT|GPIO_PULLDOWN))
|
||||
|
||||
#define GPIO_GPIO5_INPUT /* PWM6 */ _MK_GPIO_INPUT(GPIO_TIM5_CH4IN)
|
||||
#define GPIO_GPIO4_INPUT /* PWM5 */ _MK_GPIO_INPUT(GPIO_TIM8_CH4IN)
|
||||
#define GPIO_GPIO3_INPUT /* PWM4 */ _MK_GPIO_INPUT(GPIO_TIM1_CH2IN)
|
||||
#define GPIO_GPIO2_INPUT /* PWM3 */ _MK_GPIO_INPUT(GPIO_TIM1_CH1IN)
|
||||
#define GPIO_GPIO1_INPUT /* PWM2 */ _MK_GPIO_INPUT(GPIO_TIM3_CH4IN)
|
||||
#define GPIO_GPIO0_INPUT /* PWM1 */ _MK_GPIO_INPUT(GPIO_TIM3_CH3IN)
|
||||
|
||||
/* Tone alarm output */
|
||||
#define GPIO_TONE_ALARM_IDLE /* PD15 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN15)
|
||||
#define GPIO_TONE_ALARM_GPIO /* PD15 */ (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN15)
|
||||
|
||||
/* USB OTG FS
|
||||
*
|
||||
* PA8 OTG_FS_VBUS VBUS sensing
|
||||
*/
|
||||
#define GPIO_OTGFS_VBUS /* PA8 */ (GPIO_INPUT|GPIO_PULLDOWN|GPIO_SPEED_100MHz|GPIO_PORTA|GPIO_PIN8)
|
||||
|
||||
/* High-resolution timer */
|
||||
#define HRT_TIMER 2 /* use timer 2 for the HRT */
|
||||
#define HRT_TIMER_CHANNEL 1 /* use capture/compare channel 1 */
|
||||
|
||||
/* RC Serial port */
|
||||
|
||||
#define RC_SERIAL_PORT "/dev/ttyS4"
|
||||
|
||||
#define GPIO_RSSI_IN /* PC5 */ (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTC|GPIO_PIN5)
|
||||
|
||||
/* By Providing BOARD_ADC_USB_CONNECTED (using the px4_arch abstraction)
|
||||
* this board support the ADC system_power interface, and therefore
|
||||
* provides the true logic GPIO BOARD_ADC_xxxx macros.
|
||||
*/
|
||||
#define BOARD_ADC_USB_CONNECTED (px4_arch_gpioread(GPIO_OTGFS_VBUS))
|
||||
|
||||
#if BOARD_HAS_USB_VALID == 1
|
||||
# define BOARD_ADC_USB_VALID (!px4_arch_gpioread(GPIO_nVDD_USB_VALID))
|
||||
#else
|
||||
# define BOARD_ADC_USB_VALID BOARD_ADC_USB_CONNECTED
|
||||
#endif
|
||||
|
||||
#define BOARD_ADC_SERVO_VALID (1)
|
||||
#define BOARD_ADC_BRICK1_VALID (1)
|
||||
|
||||
#define BOARD_HAS_PWM DIRECT_PWM_OUTPUT_CHANNELS
|
||||
|
||||
/* This board provides a DMA pool and APIs */
|
||||
#define BOARD_DMA_ALLOC_POOL_SIZE 5120
|
||||
|
||||
/* This board provides the board_on_reset interface */
|
||||
#define BOARD_HAS_ON_RESET 1
|
||||
|
||||
/* The list of GPIO that will be initialized */
|
||||
|
||||
#define PX4_GPIO_PWM_INIT_LIST { \
|
||||
GPIO_GPIO5_INPUT, \
|
||||
GPIO_GPIO4_INPUT, \
|
||||
GPIO_GPIO3_INPUT, \
|
||||
GPIO_GPIO2_INPUT, \
|
||||
GPIO_GPIO1_INPUT, \
|
||||
GPIO_GPIO0_INPUT, \
|
||||
}
|
||||
|
||||
#define PX4_GPIO_INIT_LIST { \
|
||||
PX4_ADC_GPIO, \
|
||||
GPIO_TONE_ALARM_IDLE, \
|
||||
GPIO_RSSI_IN, \
|
||||
}
|
||||
|
||||
#define BOARD_ENABLE_CONSOLE_BUFFER
|
||||
|
||||
__BEGIN_DECLS
|
||||
|
||||
/****************************************************************************************************
|
||||
* Public Types
|
||||
****************************************************************************************************/
|
||||
|
||||
/****************************************************************************************************
|
||||
* Public data
|
||||
****************************************************************************************************/
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
/****************************************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************************************/
|
||||
|
||||
/****************************************************************************************************
|
||||
* Name: stm32_spiinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to configure SPI chip select GPIO pins for the board.
|
||||
*
|
||||
****************************************************************************************************/
|
||||
|
||||
extern void stm32_spiinitialize(void);
|
||||
|
||||
void board_spi_reset(int ms);
|
||||
|
||||
extern void stm32_usbinitialize(void);
|
||||
|
||||
extern void board_peripheral_reset(int ms);
|
||||
|
||||
|
||||
/****************************************************************************
|
||||
* Name: nsh_archinitialize
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture specific initialization for NSH.
|
||||
*
|
||||
* CONFIG_NSH_ARCHINIT=y :
|
||||
* Called from the NSH library
|
||||
*
|
||||
* CONFIG_BOARD_INITIALIZE=y, CONFIG_NSH_LIBRARY=y, &&
|
||||
* CONFIG_NSH_ARCHINIT=n :
|
||||
* Called from board_initialize().
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
#ifdef CONFIG_NSH_LIBRARY
|
||||
int nsh_archinitialize(void);
|
||||
#endif
|
||||
|
||||
#include <drivers/boards/common/board_common.h>
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
|
||||
__END_DECLS
|
||||
269
boards/holybro/kakutef7/src/init.c
Normal file
269
boards/holybro/kakutef7/src/init.c
Normal file
@ -0,0 +1,269 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (c) 2019 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/**
|
||||
* @file init.c
|
||||
*
|
||||
* Board-specific early startup code. This file implements the
|
||||
* nsh_archinitialize() function that is called early by nsh during startup.
|
||||
*
|
||||
* Code here is run before the rcS script is invoked; it should start required
|
||||
* subsystems and perform board-specific initialisation.
|
||||
*/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include "board_config.h"
|
||||
|
||||
#include <stdbool.h>
|
||||
#include <stdio.h>
|
||||
#include <string.h>
|
||||
#include <debug.h>
|
||||
#include <errno.h>
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <nuttx/board.h>
|
||||
#include <nuttx/spi/spi.h>
|
||||
#include <nuttx/analog/adc.h>
|
||||
#include <nuttx/mmcsd.h>
|
||||
#include <nuttx/mm/gran.h>
|
||||
#include <chip.h>
|
||||
#include <stm32_uart.h>
|
||||
#include <arch/board/board.h>
|
||||
#include "up_internal.h"
|
||||
|
||||
#include <drivers/drv_hrt.h>
|
||||
#include <drivers/drv_board_led.h>
|
||||
#include <systemlib/px4_macros.h>
|
||||
#include <px4_init.h>
|
||||
#include <drivers/boards/common/board_dma_alloc.h>
|
||||
|
||||
# if defined(FLASH_BASED_PARAMS)
|
||||
# include <parameters/flashparams/flashfs.h>
|
||||
#endif
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-Processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Configuration ************************************************************/
|
||||
|
||||
/*
|
||||
* Ideally we'd be able to get these from up_internal.h,
|
||||
* but since we want to be able to disable the NuttX use
|
||||
* of leds for system indication at will and there is no
|
||||
* separate switch, we need to build independent of the
|
||||
* CONFIG_ARCH_LEDS configuration switch.
|
||||
*/
|
||||
__BEGIN_DECLS
|
||||
extern void led_init(void);
|
||||
extern void led_on(int led);
|
||||
extern void led_off(int led);
|
||||
__END_DECLS
|
||||
|
||||
/************************************************************************************
|
||||
* Name: board_peripheral_reset
|
||||
*
|
||||
* Description:
|
||||
*
|
||||
************************************************************************************/
|
||||
__EXPORT void board_peripheral_reset(int ms)
|
||||
{
|
||||
UNUSED(ms);
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: board_on_reset
|
||||
*
|
||||
* Description:
|
||||
* Optionally provided function called on entry to board_system_reset
|
||||
* It should perform any house keeping prior to the rest.
|
||||
*
|
||||
* status - 1 if resetting to boot loader
|
||||
* 0 if just resetting
|
||||
*
|
||||
************************************************************************************/
|
||||
__EXPORT void board_on_reset(int status)
|
||||
{
|
||||
/* configure the GPIO pins to outputs and keep them low */
|
||||
|
||||
const uint32_t gpio[] = PX4_GPIO_PWM_INIT_LIST;
|
||||
board_gpio_init(gpio, arraySize(gpio));
|
||||
|
||||
if (status >= 0) {
|
||||
up_mdelay(6);
|
||||
}
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_boardinitialize
|
||||
*
|
||||
* Description:
|
||||
* All STM32 architectures must provide the following entry point. This entry point
|
||||
* is called early in the initialization -- after all memory has been configured
|
||||
* and mapped but before any devices have been initialized.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
__EXPORT void
|
||||
stm32_boardinitialize(void)
|
||||
{
|
||||
board_on_reset(-1); /* Reset PWM first thing */
|
||||
|
||||
/* configure LEDs */
|
||||
|
||||
board_autoled_initialize();
|
||||
|
||||
/* configure pins */
|
||||
|
||||
const uint32_t gpio[] = PX4_GPIO_INIT_LIST;
|
||||
board_gpio_init(gpio, arraySize(gpio));
|
||||
|
||||
/* configure SPI interfaces */
|
||||
|
||||
stm32_spiinitialize();
|
||||
|
||||
/* configure USB interfaces */
|
||||
|
||||
stm32_usbinitialize();
|
||||
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: board_app_initialize
|
||||
*
|
||||
* Description:
|
||||
* Perform application specific initialization. This function is never
|
||||
* called directly from application code, but only indirectly via the
|
||||
* (non-standard) boardctl() interface using the command BOARDIOC_INIT.
|
||||
*
|
||||
* Input Parameters:
|
||||
* arg - The boardctl() argument is passed to the board_app_initialize()
|
||||
* implementation without modification. The argument has no
|
||||
* meaning to NuttX; the meaning of the argument is a contract
|
||||
* between the board-specific initalization logic and the the
|
||||
* matching application logic. The value cold be such things as a
|
||||
* mode enumeration value, a set of DIP switch switch settings, a
|
||||
* pointer to configuration data read from a file or serial FLASH,
|
||||
* or whatever you would like to do with it. Every implementation
|
||||
* should accept zero/NULL as a default configuration.
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero (OK) is returned on success; a negated errno value is returned on
|
||||
* any failure to indicate the nature of the failure.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
|
||||
__EXPORT int board_app_initialize(uintptr_t arg)
|
||||
{
|
||||
|
||||
px4_platform_init();
|
||||
|
||||
/* configure the DMA allocator */
|
||||
|
||||
if (board_dma_alloc_init() < 0) {
|
||||
syslog(LOG_ERR, "[boot] DMA alloc FAILED\n");
|
||||
}
|
||||
|
||||
/* set up the serial DMA polling */
|
||||
static struct hrt_call serial_dma_call;
|
||||
struct timespec ts;
|
||||
|
||||
/*
|
||||
* Poll at 1ms intervals for received bytes that have not triggered
|
||||
* a DMA event.
|
||||
*/
|
||||
ts.tv_sec = 0;
|
||||
ts.tv_nsec = 1000000;
|
||||
|
||||
hrt_call_every(&serial_dma_call,
|
||||
ts_to_abstime(&ts),
|
||||
ts_to_abstime(&ts),
|
||||
(hrt_callout)stm32_serial_dma_poll,
|
||||
NULL);
|
||||
|
||||
|
||||
/* initial LED state */
|
||||
drv_led_start();
|
||||
led_off(LED_RED);
|
||||
led_on(LED_GREEN); // Indicate Power.
|
||||
led_off(LED_BLUE);
|
||||
|
||||
if (board_hardfault_init(2, true) != 0) {
|
||||
led_on(LED_RED);
|
||||
}
|
||||
|
||||
/* Get the SPI port for the microSD slot */
|
||||
struct spi_dev_s *spi_dev = stm32_spibus_initialize(CONFIG_NSH_MMCSDSPIPORTNO);
|
||||
|
||||
if (!spi_dev) {
|
||||
syslog(LOG_ERR, "[boot] FAILED to initialize SPI port %d\n", CONFIG_NSH_MMCSDSPIPORTNO);
|
||||
led_on(LED_BLUE);
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
/* Now bind the SPI interface to the MMCSD driver */
|
||||
int result = mmcsd_spislotinitialize(CONFIG_NSH_MMCSDMINOR, CONFIG_NSH_MMCSDSLOTNO, spi_dev);
|
||||
|
||||
if (result != OK) {
|
||||
led_on(LED_BLUE);
|
||||
syslog(LOG_ERR, "[boot] FAILED to bind SPI port 1 to the MMCSD driver\n");
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
up_udelay(20);
|
||||
|
||||
|
||||
#if defined(FLASH_BASED_PARAMS)
|
||||
static sector_descriptor_t params_sector_map[] = {
|
||||
{1, 32 * 1024, 0x08008000},
|
||||
{2, 32 * 1024, 0x08010000},
|
||||
{0, 0, 0},
|
||||
};
|
||||
|
||||
/* Initialize the flashfs layer to use heap allocated memory */
|
||||
result = parameter_flashfs_init(params_sector_map, NULL, 0);
|
||||
|
||||
if (result != OK) {
|
||||
syslog(LOG_ERR, "[boot] FAILED to init params in FLASH %d\n", result);
|
||||
led_on(LED_AMBER);
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
return OK;
|
||||
}
|
||||
108
boards/holybro/kakutef7/src/led.c
Normal file
108
boards/holybro/kakutef7/src/led.c
Normal file
@ -0,0 +1,108 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (c) 2019 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/**
|
||||
* @file led.c
|
||||
*
|
||||
* LED backend.
|
||||
*/
|
||||
|
||||
#include <px4_config.h>
|
||||
|
||||
#include <stdbool.h>
|
||||
|
||||
#include "chip.h"
|
||||
#include "stm32_gpio.h"
|
||||
#include "board_config.h"
|
||||
|
||||
#include <nuttx/board.h>
|
||||
#include <arch/board/board.h>
|
||||
|
||||
/*
|
||||
* Ideally we'd be able to get these from up_internal.h,
|
||||
* but since we want to be able to disable the NuttX use
|
||||
* of leds for system indication at will and there is no
|
||||
* separate switch, we need to build independent of the
|
||||
* CONFIG_ARCH_LEDS configuration switch.
|
||||
*/
|
||||
__BEGIN_DECLS
|
||||
extern void led_init(void);
|
||||
extern void led_on(int led);
|
||||
extern void led_off(int led);
|
||||
extern void led_toggle(int led);
|
||||
__END_DECLS
|
||||
|
||||
static uint32_t g_ledmap[] = {
|
||||
GPIO_nLED_BLUE, // Indexed by LED_BLUE
|
||||
};
|
||||
|
||||
__EXPORT void led_init(void)
|
||||
{
|
||||
for (size_t l = 0; l < (sizeof(g_ledmap) / sizeof(g_ledmap[0])); l++) {
|
||||
stm32_configgpio(g_ledmap[l]);
|
||||
}
|
||||
}
|
||||
|
||||
static void phy_set_led(int led, bool state)
|
||||
{
|
||||
/* Drive Low to switch on */
|
||||
if (led == 0) {
|
||||
stm32_gpiowrite(g_ledmap[led], !state);
|
||||
}
|
||||
}
|
||||
|
||||
static bool phy_get_led(int led)
|
||||
{
|
||||
/* If Low it is on */
|
||||
if (led == 0) {
|
||||
return !stm32_gpioread(g_ledmap[led]);
|
||||
}
|
||||
|
||||
return false;
|
||||
}
|
||||
|
||||
__EXPORT void led_on(int led)
|
||||
{
|
||||
phy_set_led(led, true);
|
||||
}
|
||||
|
||||
__EXPORT void led_off(int led)
|
||||
{
|
||||
phy_set_led(led, false);
|
||||
}
|
||||
|
||||
__EXPORT void led_toggle(int led)
|
||||
{
|
||||
phy_set_led(led, !phy_get_led(led));
|
||||
}
|
||||
|
||||
211
boards/holybro/kakutef7/src/spi.cpp
Normal file
211
boards/holybro/kakutef7/src/spi.cpp
Normal file
@ -0,0 +1,211 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (C) 2019 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/**
|
||||
* @file spi.cpp
|
||||
*
|
||||
* Board-specific SPI functions.
|
||||
*/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <board_config.h>
|
||||
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
#include <unistd.h>
|
||||
|
||||
#include <nuttx/spi/spi.h>
|
||||
#include <arch/board/board.h>
|
||||
#include <systemlib/px4_macros.h>
|
||||
|
||||
#include <up_arch.h>
|
||||
#include <chip.h>
|
||||
#include <stm32_gpio.h>
|
||||
#include "board_config.h"
|
||||
|
||||
/* Define CS GPIO array */
|
||||
static constexpr uint32_t spi1selects_gpio[] = PX4_SD_CARD_BUS_CS_GPIO;
|
||||
static constexpr uint32_t spi2selects_gpio[] = PX4_OSD_BUS_CS_GPIO;
|
||||
static constexpr uint32_t spi4selects_gpio[] = PX4_SENSOR_BUS_CS_GPIO;
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_spiinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to configure SPI chip select GPIO pins for the board.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
__EXPORT void stm32_spiinitialize()
|
||||
{
|
||||
#ifdef CONFIG_STM32F7_SPI1
|
||||
|
||||
for (auto gpio : spi1selects_gpio) {
|
||||
px4_arch_configgpio(gpio);
|
||||
}
|
||||
|
||||
#endif // CONFIG_STM32F7_SPI1
|
||||
|
||||
|
||||
#if defined(CONFIG_STM32F7_SPI2)
|
||||
|
||||
for (auto gpio : spi2selects_gpio) {
|
||||
px4_arch_configgpio(gpio);
|
||||
}
|
||||
|
||||
#endif // CONFIG_STM32F7_SPI2
|
||||
|
||||
|
||||
#ifdef CONFIG_STM32F7_SPI4
|
||||
|
||||
for (auto gpio : spi4selects_gpio) {
|
||||
px4_arch_configgpio(gpio);
|
||||
}
|
||||
|
||||
#endif // CONFIG_STM32F7_SPI4
|
||||
|
||||
|
||||
#ifdef CONFIG_STM32F7_SPI5
|
||||
|
||||
for (auto gpio : spi5selects_gpio) {
|
||||
px4_arch_configgpio(gpio);
|
||||
}
|
||||
|
||||
#endif // CONFIG_STM32F7_SPI5
|
||||
|
||||
|
||||
#ifdef CONFIG_STM32F7_SPI6
|
||||
|
||||
for (auto gpio : spi6selects_gpio) {
|
||||
px4_arch_configgpio(gpio);
|
||||
}
|
||||
|
||||
#endif // CONFIG_STM32F7_SPI6
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_spi1select and stm32_spi1status
|
||||
*
|
||||
* Description:
|
||||
* Called by stm32 spi driver on bus 1.
|
||||
*
|
||||
************************************************************************************/
|
||||
#ifdef CONFIG_STM32F7_SPI1
|
||||
__EXPORT void stm32_spi1select(FAR struct spi_dev_s *dev, uint32_t devid, bool selected)
|
||||
{
|
||||
ASSERT(devid == SPIDEV_MMCSD(0));
|
||||
|
||||
// Making sure the other peripherals are not selected
|
||||
for (auto cs : spi1selects_gpio) {
|
||||
stm32_gpiowrite(cs, 1);
|
||||
}
|
||||
|
||||
// SPI select is active low, so write !selected to select the device
|
||||
stm32_gpiowrite(spi1selects_gpio[PX4_SPI_DEV_ID(devid)], !selected);
|
||||
}
|
||||
|
||||
__EXPORT uint8_t stm32_spi1status(FAR struct spi_dev_s *dev, uint32_t devid)
|
||||
{
|
||||
return SPI_STATUS_PRESENT;
|
||||
}
|
||||
#endif // CONFIG_STM32F7_SPI1
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_spi2select and stm32_spi2status
|
||||
*
|
||||
* Description:
|
||||
* Called by stm32 spi driver on bus 2.
|
||||
*
|
||||
************************************************************************************/
|
||||
#if defined(CONFIG_STM32F7_SPI2)
|
||||
__EXPORT void stm32_spi2select(FAR struct spi_dev_s *dev, uint32_t devid, bool selected)
|
||||
{
|
||||
ASSERT(PX4_SPI_BUS_ID(devid) == PX4_SPI_BUS_OSD);
|
||||
|
||||
// Making sure the other peripherals are not selected
|
||||
for (auto cs : spi2selects_gpio) {
|
||||
stm32_gpiowrite(cs, 1);
|
||||
}
|
||||
|
||||
// SPI select is active low, so write !selected to select the device
|
||||
stm32_gpiowrite(spi2selects_gpio[PX4_SPI_DEV_ID(devid)], !selected);
|
||||
}
|
||||
|
||||
__EXPORT uint8_t stm32_spi2status(FAR struct spi_dev_s *dev, uint32_t devid)
|
||||
{
|
||||
return SPI_STATUS_PRESENT;
|
||||
}
|
||||
#endif // CONFIG_STM32F7_SPI2 && GPIO_SPI2_CS_FRAM
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_spi4select and stm32_spi4status
|
||||
*
|
||||
* Description:
|
||||
* Called by stm32 spi driver on bus 4.
|
||||
*
|
||||
************************************************************************************/
|
||||
#ifdef CONFIG_STM32F7_SPI4
|
||||
__EXPORT void stm32_spi4select(FAR struct spi_dev_s *dev, uint32_t devid, bool selected)
|
||||
{
|
||||
ASSERT(PX4_SPI_BUS_ID(devid) == PX4_SPI_BUS_SENSORS);
|
||||
|
||||
// Making sure the other peripherals are not selected
|
||||
for (auto cs : spi4selects_gpio) {
|
||||
stm32_gpiowrite(cs, 1);
|
||||
}
|
||||
|
||||
// SPI select is active low, so write !selected to select the device
|
||||
stm32_gpiowrite(spi4selects_gpio[PX4_SPI_DEV_ID(devid)], !selected);
|
||||
}
|
||||
|
||||
__EXPORT uint8_t stm32_spi4status(FAR struct spi_dev_s *dev, uint32_t devid)
|
||||
{
|
||||
return SPI_STATUS_PRESENT;
|
||||
}
|
||||
#endif // CONFIG_STM32F7_SPI4
|
||||
|
||||
/************************************************************************************
|
||||
* Name: board_spi_reset
|
||||
*
|
||||
* Description:
|
||||
*
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
__EXPORT void board_spi_reset(int ms)
|
||||
{
|
||||
}
|
||||
148
boards/holybro/kakutef7/src/timer_config.c
Normal file
148
boards/holybro/kakutef7/src/timer_config.c
Normal file
@ -0,0 +1,148 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (C) 2019 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/**
|
||||
* @file timer_config.c
|
||||
*
|
||||
* Configuration data for the stm32 pwm_servo, input capture and pwm input driver.
|
||||
*
|
||||
* Note that these arrays must always be fully-sized.
|
||||
*/
|
||||
|
||||
#include <stdint.h>
|
||||
|
||||
#include <chip.h>
|
||||
#include <stm32_gpio.h>
|
||||
#include <stm32_tim.h>
|
||||
|
||||
#include <drivers/drv_pwm_output.h>
|
||||
#include <drivers/stm32/drv_io_timer.h>
|
||||
|
||||
#include "board_config.h"
|
||||
|
||||
__EXPORT const io_timers_t io_timers[MAX_IO_TIMERS] = {
|
||||
{
|
||||
.base = STM32_TIM3_BASE,
|
||||
.clock_register = STM32_RCC_APB1ENR,
|
||||
.clock_bit = RCC_APB1ENR_TIM3EN,
|
||||
.clock_freq = STM32_APB1_TIM3_CLKIN,
|
||||
.first_channel_index = 0,
|
||||
.last_channel_index = 1,
|
||||
.handler = io_timer_handler0,
|
||||
.vectorno = STM32_IRQ_TIM3,
|
||||
|
||||
},
|
||||
{
|
||||
.base = STM32_TIM1_BASE,
|
||||
.clock_register = STM32_RCC_APB2ENR,
|
||||
.clock_bit = RCC_APB2ENR_TIM1EN,
|
||||
.clock_freq = STM32_APB2_TIM1_CLKIN,
|
||||
.first_channel_index = 2,
|
||||
.last_channel_index = 3,
|
||||
.handler = io_timer_handler1,
|
||||
.vectorno = STM32_IRQ_TIM1CC,
|
||||
|
||||
},
|
||||
{
|
||||
.base = STM32_TIM8_BASE,
|
||||
.clock_register = STM32_RCC_APB2ENR,
|
||||
.clock_bit = RCC_APB2ENR_TIM8EN,
|
||||
.clock_freq = STM32_APB2_TIM8_CLKIN,
|
||||
.first_channel_index = 4,
|
||||
.last_channel_index = 4,
|
||||
.handler = io_timer_handler2,
|
||||
.vectorno = STM32_IRQ_TIM8CC,
|
||||
},
|
||||
{
|
||||
.base = STM32_TIM5_BASE,
|
||||
.clock_register = STM32_RCC_APB1ENR,
|
||||
.clock_bit = RCC_APB1ENR_TIM5EN,
|
||||
.clock_freq = STM32_APB1_TIM5_CLKIN,
|
||||
.first_channel_index = 5,
|
||||
.last_channel_index = 5,
|
||||
.handler = io_timer_handler3,
|
||||
.vectorno = STM32_IRQ_TIM5,
|
||||
}
|
||||
};
|
||||
|
||||
__EXPORT const timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = {
|
||||
{
|
||||
.gpio_out = GPIO_TIM3_CH3OUT,
|
||||
.gpio_in = GPIO_TIM3_CH3IN,
|
||||
.timer_index = 0,
|
||||
.timer_channel = 3,
|
||||
.ccr_offset = STM32_GTIM_CCR3_OFFSET,
|
||||
.masks = GTIM_SR_CC3IF | GTIM_SR_CC3OF
|
||||
},
|
||||
{
|
||||
.gpio_out = GPIO_TIM3_CH4OUT,
|
||||
.gpio_in = GPIO_TIM3_CH4IN,
|
||||
.timer_index = 0,
|
||||
.timer_channel = 4,
|
||||
.ccr_offset = STM32_GTIM_CCR4_OFFSET,
|
||||
.masks = GTIM_SR_CC4IF | GTIM_SR_CC4OF
|
||||
},
|
||||
{
|
||||
.gpio_out = GPIO_TIM1_CH1OUT,
|
||||
.gpio_in = GPIO_TIM1_CH1IN,
|
||||
.timer_index = 1,
|
||||
.timer_channel = 1,
|
||||
.ccr_offset = STM32_GTIM_CCR1_OFFSET,
|
||||
.masks = GTIM_SR_CC1IF | GTIM_SR_CC1OF
|
||||
},
|
||||
{
|
||||
.gpio_out = GPIO_TIM1_CH2OUT,
|
||||
.gpio_in = GPIO_TIM1_CH2IN,
|
||||
.timer_index = 1,
|
||||
.timer_channel = 2,
|
||||
.ccr_offset = STM32_GTIM_CCR2_OFFSET,
|
||||
.masks = GTIM_SR_CC2IF | GTIM_SR_CC2OF
|
||||
},
|
||||
{
|
||||
.gpio_out = GPIO_TIM8_CH4OUT,
|
||||
.gpio_in = GPIO_TIM8_CH4IN,
|
||||
.timer_index = 2,
|
||||
.timer_channel = 4,
|
||||
.ccr_offset = STM32_GTIM_CCR4_OFFSET,
|
||||
.masks = GTIM_SR_CC4IF | GTIM_SR_CC4OF
|
||||
},
|
||||
{
|
||||
.gpio_out = GPIO_TIM5_CH4OUT,
|
||||
.gpio_in = GPIO_TIM5_CH4IN,
|
||||
.timer_index = 3,
|
||||
.timer_channel = 4,
|
||||
.ccr_offset = STM32_GTIM_CCR4_OFFSET,
|
||||
.masks = GTIM_SR_CC4IF | GTIM_SR_CC4OF
|
||||
},
|
||||
};
|
||||
|
||||
105
boards/holybro/kakutef7/src/usb.c
Normal file
105
boards/holybro/kakutef7/src/usb.c
Normal file
@ -0,0 +1,105 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (C) 2019 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/**
|
||||
* @file usb.c
|
||||
*
|
||||
* Board-specific USB functions.
|
||||
*/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <px4_config.h>
|
||||
|
||||
#include <sys/types.h>
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/usb/usbdev.h>
|
||||
#include <nuttx/usb/usbdev_trace.h>
|
||||
|
||||
#include <up_arch.h>
|
||||
#include <chip.h>
|
||||
#include <stm32_gpio.h>
|
||||
#include <stm32_otg.h>
|
||||
#include "board_config.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Private Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Public Functions
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_usbinitialize
|
||||
*
|
||||
* Description:
|
||||
* Called to setup USB-related GPIO pins for the board.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
__EXPORT void stm32_usbinitialize(void)
|
||||
{
|
||||
/* The OTG FS has an internal soft pull-up */
|
||||
|
||||
/* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */
|
||||
|
||||
#ifdef CONFIG_STM32F7_OTGFS
|
||||
stm32_configgpio(GPIO_OTGFS_VBUS);
|
||||
#endif
|
||||
}
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_usbsuspend
|
||||
*
|
||||
* Description:
|
||||
* Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is
|
||||
* used. This function is called whenever the USB enters or leaves suspend mode.
|
||||
* This is an opportunity for the board logic to shutdown clocks, power, etc.
|
||||
* while the USB is suspended.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume)
|
||||
{
|
||||
uinfo("resume: %d\n", resume);
|
||||
}
|
||||
Loading…
x
Reference in New Issue
Block a user