fly316/PX4-Autopilot
7
0
Fork 0
mirror of https://gitee.com/mirrors_PX4/PX4-Autopilot.git synced 2026-10-21 07:13:34 +08:00
Code Issues Packages Projects Releases Wiki Activity

docs: Remove all discontinued FCs (#26642)

Browse Source
This commit is contained in:
Hamish Willee
2026-03-05 08:03:07 +11:00
committed by GitHub
parent 2cb9b9bfbe
commit 1cb2debbb9
23 changed files with 115 additions and 2929 deletions
Download Patch File Download Diff File Expand all files Collapse all files
docs/en/flight_controller/pixhawk.md
+5 -336
View File
@@ -1,337 +1,6 @@
<Redirect to="../flight_controller/autopilot_discontinued" />
<!--
# 3DR Pixhawk 1 Flight Controller (Discontinued)
::: warning
This flight controller has been [discontinued](../flight_controller/autopilot_experimental.md) and is no longer commercially available.
You can use the [mRo Pixhawk](../flight_controller/mro_pixhawk.md) as a drop-in replacement.
:::
::: warning
PX4 does not manufacture this (or any) autopilot.
Contact the manufacturer for support or compliance issues.
:::
The _3DR Pixhawk<sup>&reg;</sup> 1_ autopilot is a popular general purpose flight controller based on the [Pixhawk-project](https://pixhawk.org/) **FMUv2** open hardware design (it combines the functionality of the PX4FMU + PX4IO).
It runs PX4 on the [NuttX](https://nuttx.apache.org/) OS.
![Pixhawk Image](../../assets/hardware/hardware-pixhawk.png)
Assembly/setup instructions for use with PX4 are provided here: [Pixhawk Wiring Quickstart](../assembly/quick_start_pixhawk.md)
## Key Features
- Main System-on-Chip: [STM32F427](https://www.st.com/en/microcontrollers-microprocessors/stm32f427-437.html)
- CPU: 180 MHz ARM<sup>&reg;</sup> Cortex<sup>&reg;</sup> M4 with single-precision FPU
- RAM: 256 KB SRAM (L1)
- Failsafe System-on-Chip: STM32F100
- CPU: 24 MHz ARM Cortex M3
- RAM: 8 KB SRAM
- Wifi: ESP8266 external
- GPS: u-blox<sup>&reg;</sup> 7/8 (Hobbyking<sup>&reg;</sup>) / u-blox 6 (3D Robotics)
- Optical flow: [PX4 Flow unit](../sensor/px4flow.md)
- Redundant power supply inputs and automatic failover
- External safety switch
- Multicolor LED main visual indicator
- High-power, multi-tone piezo audio indicator
- microSD card for high-rate logging over extended periods of time
Connectivity
- 1x I2C
- 1x CAN (2x optional)
- 1x ADC
- 4x UART (2x with flow control)
- 1x Console
- 8x PWM with manual override
- 6x PWM / GPIO / PWM input
- S.BUS / PPM / Spektrum input
- S.BUS output
# Where to Buy {#store}
Originally manufactured by 3DR&reg; this board was the original standard microcontroller platform for PX4&reg;. While the board is no longer manufactured by 3DR, you can use the [mRo Pixhawk](../flight_controller/mro_pixhawk.md) as a drop-in replacement.
Order mRo Pixhawk from:
- [Bare Bones](https://store.mrobotics.io/Genuine-PixHawk-1-Barebones-p/mro-pixhawk1-bb-mr.htm) - Just the board (useful as a 3DR Pixhawk replacement)
- [mRo Pixhawk 2.4.6 Essential Kit](https://store.mrobotics.io/Genuine-PixHawk-Flight-Controller-p/mro-pixhawk1-minkit-mr.htm) - includes everything except for telemetry radios
- [mRo Pixhawk 2.4.6 Cool Kit! (Limited edition)](https://store.mrobotics.io/product-p/mro-pixhawk1-fullkit-mr.htm) - includes everything you need including telemetry radios
## Specifications
### Processor
- 32bit STM32F427 [Cortex-M4F](https://en.wikipedia.org/wiki/ARM_Cortex-M#Cortex-M4) core with FPU
- 168 MHz
- 256 KB RAM
- 2 MB Flash
- 32 bit STM32F103 failsafe co-processor
### Sensors
- ST Micro L3GD20H 16 bit gyroscope
- ST Micro LSM303D 14 bit accelerometer / magnetometer
- Invensense MPU 6000 3-axis accelerometer/gyroscope
- MEAS MS5611 barometer
### Interfaces
- 5x UART (serial ports), one high-power capable, 2x with HW flow control
- 2x CAN (one with internal 3.3V transceiver, one on expansion connector)
- Spektrum DSM / DSM2 / DSM-X® Satellite compatible input
- Futaba S.BUS® compatible input and output
- PPM sum signal input
- RSSI (PWM or voltage) input
- I2C
- SPI
- 3.3 and 6.6V ADC inputs
- Internal microUSB port and external microUSB port extension
<lite-youtube videoid="gCCC5A-Bvv4" title="PX4 Pixhawk (3DR) Multicolor Led in action"/>
### Power System and Protection
- Ideal diode controller with automatic failover
- Servo rail high-power (max. 10V) and high-current (10A+) ready
- All peripheral outputs over-current protected, all inputs ESD protected
## Voltage Ratings
Pixhawk can be triple-redundant on the power supply if three power sources are supplied. The three rails are: Power module input, servo rail input, USB input.
### Normal Operation Maximum Ratings
Under these conditions all power sources will be used in this order to power the system
- Power module input (4.8V to 5.4V)
- Servo rail input (4.8V to 5.4V) **UP TO 10V FOR MANUAL OVERRIDE, BUT AUTOPILOT PART WILL BE UNPOWERED ABOVE 5.7V IF POWER MODULE INPUT IS NOT PRESENT**
- USB power input (4.8V to 5.4V)
### Absolute Maximum Ratings
Under these conditions the system will not draw any power (will not be operational), but will remain intact.
- Power module input (4.1V to 5.7V, 0V to 20V undamaged)
- Servo rail input (4.1V to 5.7V, 0V to 20V)
- USB power input (4.1V to 5.7V, 0V to 6V)
## Schematics
[FMUv2 + IOv2 schematic](https://raw.githubusercontent.com/PX4/Hardware/master/FMUv2/PX4FMUv2.4.5.pdf) -- Schematic and layout
::: info
As a CC-BY-SA 3.0 licensed Open Hardware design, all schematics and design files are [available](https://github.com/pixhawk/Hardware).
:::
## Connections
Pixhawk ports are shown below.
These use Hirose DF13 connectors (predating the JST-GH connectors defined in the Pixhawk connector standard).
::: warning
Many 3DR Pixhawk clones use Molex picoblade connectors instead of DF13 connectors.
They have rectangular instead of square pins, and cannot be assumed to be compatible.
:::
![Pixhawk Connectors](../../assets/flight_controller/pixhawk1/pixhawk_connectors.png)
::: tip
The `RC IN` port is for RC receivers only and provides sufficient power for that purpose.
**NEVER** connect any servos, power supplies or batteries to it or to the receiver connected to it.
:::
## Pinouts
#### TELEM1, TELEM2 ports
| Pin | Signal | Volt |
| ------- | --------- | ----- |
| 1 (red) | VCC | +5V |
| 2 (blk) | TX (OUT) | +3.3V |
| 3 (blk) | RX (IN) | +3.3V |
| 4 (blk) | CTS (IN) | +3.3V |
| 5 (blk) | RTS (OUT) | +3.3V |
| 6 (blk) | GND | GND |
#### GPS port
| Pin | Signal | Volt |
| ------- | -------- | ----- |
| 1 (red) | VCC | +5V |
| 2 (blk) | TX (OUT) | +3.3V |
| 3 (blk) | RX (IN) | +3.3V |
| 4 (blk) | CAN2 TX | +3.3V |
| 5 (blk) | CAN2 RX | +3.3V |
| 6 (blk) | GND | GND |
#### SERIAL 4/5 port
Due to space constraints two ports are on one connector.
| Pin | Signal | Volt |
| ------- | ------- | ----- |
| 1 (red) | VCC | +5V |
| 2 (blk) | TX (#4) | +3.3V |
| 3 (blk) | RX (#4) | +3.3V |
| 4 (blk) | TX (#5) | +3.3V |
| 5 (blk) | RX (#5) | +3.3V |
| 6 (blk) | GND | GND |
#### ADC 6.6V
| Pin | Signal | Volt |
| ------- | ------ | ----------- |
| 1 (red) | VCC | +5V |
| 2 (blk) | ADC IN | up to +6.6V |
| 3 (blk) | GND | GND |
#### ADC 3.3V
| Pin | Signal | Volt |
| ------- | ------ | ----------- |
| 1 (red) | VCC | +5V |
| 2 (blk) | ADC IN | up to +3.3V |
| 3 (blk) | GND | GND |
| 4 (blk) | ADC IN | up to +3.3V |
| 5 (blk) | GND | GND |
#### I2C
| Pin | Signal | Volt |
| ------- | ------ | -------------- |
| 1 (red) | VCC | +5V |
| 2 (blk) | SCL | +3.3 (pullups) |
| 3 (blk) | SDA | +3.3 (pullups) |
| 4 (blk) | GND | GND |
#### CAN
| Pin | Signal | Volt |
| ------- | ------ | ---- |
| 1 (red) | VCC | +5V |
| 2 (blk) | CAN_H | +12V |
| 3 (blk) | CAN_L | +12V |
| 4 (blk) | GND | GND |
#### SPI
| Pin | Signal | Volt |
| ------- | ------------ | ---- |
| 1 (red) | VCC | +5V |
| 2 (blk) | SPI_EXT_SCK | +3.3 |
| 3 (blk) | SPI_EXT_MISO | +3.3 |
| 4 (blk) | SPI_EXT_MOSI | +3.3 |
| 5 (blk) | !SPI_EXT_NSS | +3.3 |
| 6 (blk) | !GPIO_EXT | +3.3 |
| 7 (blk) | GND | GND |
#### POWER
| Pin | Signal | Volt |
| ------- | ------- | ----- |
| 1 (red) | VCC | +5V |
| 2 (blk) | VCC | +5V |
| 3 (blk) | CURRENT | +3.3V |
| 4 (blk) | VOLTAGE | +3.3V |
| 5 (blk) | GND | GND |
| 6 (blk) | GND | GND |
#### SWITCH
| Pin | Signal | Volt |
| ------- | -------------- | ----- |
| 1 (red) | VCC | +3.3V |
| 2 (blk) | !IO_LED_SAFETY | GND |
| 3 (blk) | SAFETY | GND |
## Serial Port Mapping
| UART | Device | Port |
| ------ | ---------- | --------------------- |
| UART1 | /dev/ttyS0 | IO debug |
| USART2 | /dev/ttyS1 | TELEM1 (flow control) |
| USART3 | /dev/ttyS2 | TELEM2 (flow control) |
| UART4 | |
| UART7 | CONSOLE |
| UART8 | SERIAL4 |
<!-- Note: Got ports using https://github.com/PX4/PX4-user_guide/pull/672#issuecomment-598198434 -->
## Debug Ports
### Console Port
The [PX4 System Console](../debug/system_console.md) runs on the port labeled [SERIAL4/5](#serial-4-5-port).
::: tip
A convenient way to connect to the console is to use a [Zubax BugFace BF1](https://github.com/Zubax/bugface_bf1), as it comes with connectors that can be used with several different Pixhawk devices.
Simply connect the 6-pos DF13 1:1 cable on the [Zubax BugFace BF1](https://github.com/Zubax/bugface_bf1) to the Pixhawk `SERIAL4/5` port.
![Zubax BugFace BF1](../../assets/flight_controller/pixhawk1/dronecode_probe.jpg)
:::
The pinout is standard serial pinout, designed to connect to a [3.3V FTDI](https://www.digikey.com/en/products/detail/TTL-232R-3V3/768-1015-ND/1836393) cable (5V tolerant).
| 3DR Pixhawk 1 | | FTDI |
| ------------- | --------- | ---- | ---------------- |
| 1 | +5V (red) | | N/C |
| 2 | S4 Tx | | N/C |
| 3 | S4 Rx | | N/C |
| 4 | S5 Tx | 5 | FTDI RX (yellow) |
| 5 | S5 Rx | 4 | FTDI TX (orange) |
| 6 | GND | 1 | FTDI GND (black) |
The wiring for an FTDI cable to a 6-pos DF13 1:1 connector is shown in the figure below.
![Console Connector](../../assets/flight_controller/pixhawk1/console_connector.jpg)
The complete wiring is shown below.
![Console Debug](../../assets/flight_controller/pixhawk1/console_debug.jpg)
::: info
For information on how to _use_ the console see: [System Console](../debug/system_console.md).
:::
### SWD Port
The [SWD](../debug/swd_debug.md) (JTAG) ports are hidden under the cover (which must be removed for hardware debugging).
There are separate ports for FMU and IO, as highlighted below.
![Pixhawk SWD](../../assets/flight_controller/pixhawk1/pixhawk_swd.jpg)
The ports are ARM 10-pin JTAG connectors, which you will probably have to solder.
The pinout for the ports is shown below (the square markers in the corners above indicates pin 1).
![ARM 10-Pin connector pinout](../../assets/flight_controller/pixhawk1/arm_10pin_jtag_connector_pinout.jpg)
::: info
All Pixhawk FMUv2 boards have a similar SWD port.
:::
## Building Firmware
::: tip
Most users will not need to build this firmware!
It is pre-built and automatically installed by _QGroundControl_ when appropriate hardware is connected.
:::
To [build PX4](../dev_setup/building_px4.md) for this target:
```sh
make px4_fmu-v2_default
```
## Parts / Housings
- **ARM MINI JTAG (J6)**: 1.27 mm 10pos header (SHROUDED), for Black Magic Probe: FCI 20021521-00010D4LF ([Digi-Key](https://www.digikey.com/en/products/detail/20021521-00010T1LF/609-4054-ND/2414951),) or Samtec FTSH-105-01-F-DV-K (untested) or Harwin M50-3600542 ([Digikey](https://www.digikey.com/en/products/detail/harwin-inc/M50-3600542/2264370))
- JTAG Adapter Option #1: [BlackMagic Probe](https://1bitsquared.com/products/black-magic-probe). Note, may come without cables (check with manufacturer).
If so, you will need the **Samtec FFSD-05-D-06.00-01-N** cable ([Samtec sample service](https://www.samtec.com/products/ffsd-05-d-06.00-01-n) or [Digi-Key Link: SAM8218-ND](https://www.digikey.com/en/products/detail/samtec-inc/ffsd-05-d-06-00-01-n/1106577)) or [Tag Connect Ribbon](https://www.tag-connect.com/product/10-pin-cortex-ribbon-cable-4-length-with-50-mil-connectors) and a Mini-USB cable.
- JTAG Adapter Option #2: [Digi-Key Link: ST-LINK/V2](https://www.digikey.com/product-detail/en/stmicroelectronics/ST-LINK-V2/497-10484-ND) / [ST USER MANUAL](https://www.st.com/resource/en/user_manual/dm00026748.pdf), needs an ARM Mini JTAG to 20pos adapter: [Digi-Key Link: 726-1193-ND](https://www.digikey.com/en/products/detail/texas-instruments/MDL-ADA2/1986451)
- JTAG Adapter Option #3: [Olimex ARM-TINY](https://www.olimex.com/wiki/ARM-USB-TINY) or any other OpenOCD-compatible ARM Cortex JTAG adapter, needs an ARM Mini JTAG to 20pos adapter: [Digi-Key Link: 726-1193-ND](https://www.digikey.com/en/products/detail/texas-instruments/MDL-ADA2/1986451)
- **USARTs**: Hirose DF13 6 pos ([Digi-Key Link: DF13A-6P-1.25H(20)](https://www.digikey.com/products/en?keywords=H3371-ND))
- Mates: Hirose DF13 6 pos housing ([Digi-Key Link: Hirose DF13-6S-1.25C](https://www.digikey.com/products/en?keywords=H2182-ND))
- **I2C and CAN**: Hirose DF13 4 pos ([Digi-Key Link: DF13A-4P-1.25H(20)](https://www.digikey.com/en/products/detail/hirose-electric-co-ltd/DF13A-4P-1-25H-20/530666) - discontinued)
## Supported Platforms / Airframes
Any multicopter / airplane / rover or boat that can be controlled with normal RC servos or Futaba S-Bus servos.
Doc removed 202604
-->