fly316/PX4-Autopilot
7
0
Fork 0
mirror of https://gitee.com/mirrors_PX4/PX4-Autopilot.git synced 2026-04-14 10:07:39 +08:00
Code Issues Packages Projects Releases Wiki Activity
PX4-Autopilot/src/drivers/px4fmu/fmu.cpp
David Sidrane f48481fcbd fmu:Use extended rc_io_invert API with UxART
2018-07-17 08:53:29 +02:00

3598 lines
82 KiB
C++
Raw Blame History

/****************************************************************************
*
* Copyright (c) 2012-2018 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name PX4 nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/**
* @file fmu.cpp
*
* Driver/configurator for the PX4 FMU
*/
#include <cfloat>
#include <board_config.h>
#include <drivers/device/device.h>
#include <drivers/device/i2c.h>
#include <drivers/drv_gpio.h>
#include <drivers/drv_hrt.h>
#include <drivers/drv_input_capture.h>
#include <drivers/drv_mixer.h>
#include <drivers/drv_pwm_output.h>
#include <drivers/drv_rc_input.h>
#include <lib/rc/dsm.h>
#include <lib/rc/sbus.h>
#include <lib/rc/st24.h>
#include <lib/rc/sumd.h>
#include <px4_config.h>
#include <px4_getopt.h>
#include <px4_log.h>
#include <px4_module.h>
#include <circuit_breaker/circuit_breaker.h>
#include <lib/mixer/mixer.h>
#include <parameters/param.h>
#include <perf/perf_counter.h>
#include <pwm_limit/pwm_limit.h>
#include <uORB/topics/actuator_armed.h>
#include <uORB/topics/actuator_controls.h>
#include <uORB/topics/actuator_outputs.h>
#include <uORB/topics/adc_report.h>
#include <uORB/topics/multirotor_motor_limits.h>
#include <uORB/topics/parameter_update.h>
#include <uORB/topics/safety.h>
#include <uORB/topics/vehicle_command.h>
#include <uORB/topics/vehicle_status.h>
#ifdef HRT_PPM_CHANNEL
# include <systemlib/ppm_decode.h>
#endif
#define SCHEDULE_INTERVAL 2000 /**< The schedule interval in usec (500 Hz) */
static constexpr uint8_t CYCLE_COUNT = 10; /* safety switch must be held for 1 second to activate */
static constexpr uint8_t MAX_ACTUATORS = DIRECT_PWM_OUTPUT_CHANNELS;
#if defined(PX4_CPU_UUID_WORD32_FORMAT)
# define CPU_UUID_FORMAT PX4_CPU_UUID_WORD32_FORMAT
#else
# define CPU_UUID_FORMAT "%0X"
#endif
#if defined(PX4_CPU_UUID_WORD32_SEPARATOR)
# define CPU_UUID_SEPARATOR PX4_CPU_UUID_WORD32_SEPARATOR
#else
# define CPU_UUID_SEPARATOR " "
#endif
/*
* Define the various LED flash sequences for each system state.
*/
#define LED_PATTERN_FMU_OK_TO_ARM 0x0003 /**< slow blinking */
#define LED_PATTERN_FMU_REFUSE_TO_ARM 0x5555 /**< fast blinking */
#define LED_PATTERN_IO_ARMED 0x5050 /**< long off, then double blink */
#define LED_PATTERN_FMU_ARMED 0x5500 /**< long off, then quad blink */
#define LED_PATTERN_IO_FMU_ARMED 0xffff /**< constantly on */
/** Mode given via CLI */
enum PortMode {
PORT_MODE_UNSET = 0,
PORT_FULL_GPIO,
PORT_FULL_PWM,
PORT_RC_IN,
PORT_PWM6,
PORT_PWM4,
PORT_PWM3,
PORT_PWM2,
PORT_PWM1,
PORT_PWM3CAP1,
PORT_PWM2CAP2,
PORT_CAPTURE,
};
#if !defined(BOARD_HAS_PWM)
# error "board_config.h needs to define BOARD_HAS_PWM"
#endif
class PX4FMU : public device::CDev, public ModuleBase<PX4FMU>
{
public:
enum Mode {
MODE_NONE,
MODE_1PWM,
MODE_2PWM,
MODE_2PWM2CAP,
MODE_3PWM,
MODE_3PWM1CAP,
MODE_4PWM,
MODE_6PWM,
MODE_8PWM,
MODE_14PWM,
MODE_4CAP,
MODE_5CAP,
MODE_6CAP,
};
PX4FMU(bool run_as_task);
virtual ~PX4FMU();
/** @see ModuleBase */
static int task_spawn(int argc, char *argv[]);
/** @see ModuleBase */
static PX4FMU *instantiate(int argc, char *argv[]);
/** @see ModuleBase */
static int custom_command(int argc, char *argv[]);
/** @see ModuleBase */
static int print_usage(const char *reason = nullptr);
/** @see ModuleBase::run() */
void run() override;
/**
* run the main loop: if running as task, continuously iterate, otherwise execute only one single cycle
*/
void cycle();
/** @see ModuleBase::print_status() */
int print_status() override;
/** change the FMU mode of the running module */
static int fmu_new_mode(PortMode new_mode);
static int test();
static int fake(int argc, char *argv[]);
virtual int ioctl(file *filp, int cmd, unsigned long arg);
virtual ssize_t write(file *filp, const char *buffer, size_t len);
virtual int init();
int set_mode(Mode mode);
Mode get_mode() { return _mode; }
int set_pwm_alt_rate(unsigned rate);
int set_pwm_alt_channels(uint32_t channels);
static int set_i2c_bus_clock(unsigned bus, unsigned clock_hz);
static void capture_trampoline(void *context, uint32_t chan_index,
hrt_abstime edge_time, uint32_t edge_state,
uint32_t overflow);
void update_pwm_trims();
private:
enum RC_SCAN {
RC_SCAN_PPM = 0,
RC_SCAN_SBUS,
RC_SCAN_DSM,
RC_SCAN_SUMD,
RC_SCAN_ST24
};
enum RC_SCAN _rc_scan_state = RC_SCAN_SBUS;
char const *RC_SCAN_STRING[5] = {
"PPM",
"SBUS",
"DSM",
"SUMD",
"ST24"
};
enum class MotorOrdering : int32_t {
PX4 = 0,
Betaflight = 1
};
hrt_abstime _rc_scan_begin = 0;
bool _rc_scan_locked = false;
bool _report_lock = true;
hrt_abstime _cycle_timestamp = 0;
hrt_abstime _last_safety_check = 0;
hrt_abstime _time_last_mix = 0;
static const unsigned _max_actuators = DIRECT_PWM_OUTPUT_CHANNELS;
Mode _mode;
unsigned _pwm_default_rate;
unsigned _pwm_alt_rate;
uint32_t _pwm_alt_rate_channels;
unsigned _current_update_rate;
bool _run_as_task;
static struct work_s _work;
int _vehicle_cmd_sub;
int _armed_sub;
int _param_sub;
int _adc_sub;
struct rc_input_values _rc_in;
float _analog_rc_rssi_volt;
bool _analog_rc_rssi_stable;
orb_advert_t _to_input_rc;
orb_advert_t _outputs_pub;
unsigned _num_outputs;
int _class_instance;
int _rcs_fd;
uint8_t _rcs_buf[SBUS_BUFFER_SIZE];
bool _throttle_armed;
bool _pwm_on;
uint32_t _pwm_mask;
bool _pwm_initialized;
MixerGroup *_mixers;
uint32_t _groups_required;
uint32_t _groups_subscribed;
int _control_subs[actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS];
actuator_controls_s _controls[actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS];
orb_id_t _control_topics[actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS];
pollfd _poll_fds[actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS];
unsigned _poll_fds_num;
uint16_t raw_rc_values[input_rc_s::RC_INPUT_MAX_CHANNELS];
uint16_t raw_rc_count;
static pwm_limit_t _pwm_limit;
static actuator_armed_s _armed;
uint16_t _failsafe_pwm[_max_actuators];
uint16_t _disarmed_pwm[_max_actuators];
uint16_t _min_pwm[_max_actuators];
uint16_t _max_pwm[_max_actuators];
uint16_t _reverse_pwm_mask;
unsigned _num_failsafe_set;
unsigned _num_disarmed_set;
bool _safety_off;
bool _safety_disabled;
orb_advert_t _to_safety;
orb_advert_t _to_mixer_status; ///< mixer status flags
float _mot_t_max; ///< maximum rise time for motor (slew rate limiting)
float _thr_mdl_fac; ///< thrust to pwm modelling factor
bool _airmode; ///< multicopter air-mode
MotorOrdering _motor_ordering;
perf_counter_t _perf_control_latency;
static bool arm_nothrottle()
{
return ((_armed.prearmed && !_armed.armed) || _armed.in_esc_calibration_mode);
}
static void cycle_trampoline(void *arg);
int start();
static int control_callback(uintptr_t handle,
uint8_t control_group,
uint8_t control_index,
float &input);
void capture_callback(uint32_t chan_index,
hrt_abstime edge_time, uint32_t edge_state, uint32_t overflow);
void subscribe();
int set_pwm_rate(unsigned rate_map, unsigned default_rate, unsigned alt_rate);
int pwm_ioctl(file *filp, int cmd, unsigned long arg);
void update_pwm_rev_mask();
void update_pwm_out_state(bool on);
void update_params();
struct GPIOConfig {
uint32_t input;
uint32_t output;
uint32_t alt;
};
#if defined(BOARD_HAS_FMU_GPIO)
static const GPIOConfig _gpio_tab[];
static const unsigned _ngpio;
#endif
static void sensor_reset(int ms);
static void peripheral_reset(int ms);
int gpio_reset(void);
int gpio_set_function(uint32_t gpios, int function);
int gpio_write(uint32_t gpios, int function);
int gpio_read(uint32_t *value);
int gpio_ioctl(file *filp, int cmd, unsigned long arg);
int capture_ioctl(file *filp, int cmd, unsigned long arg);
PX4FMU(const PX4FMU &) = delete;
PX4FMU operator=(const PX4FMU &) = delete;
void fill_rc_in(uint16_t raw_rc_count_local,
uint16_t raw_rc_values_local[input_rc_s::RC_INPUT_MAX_CHANNELS],
hrt_abstime now, bool frame_drop, bool failsafe,
unsigned frame_drops, int rssi);
void set_rc_scan_state(RC_SCAN _rc_scan_state);
void rc_io_invert(bool invert, uint32_t uxart_base);
void safety_check_button(void);
void flash_safety_button(void);
/**
* Reorder PWM outputs according to _motor_ordering
* @param values PWM values to reorder
*/
inline void reorder_outputs(uint16_t values[MAX_ACTUATORS]);
};
#if defined(BOARD_HAS_FMU_GPIO)
const PX4FMU::GPIOConfig PX4FMU::_gpio_tab[] = BOARD_FMU_GPIO_TAB;
const unsigned PX4FMU::_ngpio = arraySize(PX4FMU::_gpio_tab);
#endif
pwm_limit_t PX4FMU::_pwm_limit;
actuator_armed_s PX4FMU::_armed = {};
work_s PX4FMU::_work = {};
PX4FMU::PX4FMU(bool run_as_task) :
CDev("fmu", PX4FMU_DEVICE_PATH),
_mode(MODE_NONE),
_pwm_default_rate(50),
_pwm_alt_rate(50),
_pwm_alt_rate_channels(0),
_current_update_rate(0),
_run_as_task(run_as_task),
_vehicle_cmd_sub(-1),
_armed_sub(-1),
_param_sub(-1),
_adc_sub(-1),
_rc_in{},
_analog_rc_rssi_volt(-1.0f),
_analog_rc_rssi_stable(false),
_to_input_rc(nullptr),
_outputs_pub(nullptr),
_num_outputs(0),
_class_instance(0),
_rcs_fd(-1),
_throttle_armed(false),
_pwm_on(false),
_pwm_mask(0),
_pwm_initialized(false),
_mixers(nullptr),
_groups_required(0),
_groups_subscribed(0),
_control_subs{ -1},
_poll_fds_num(0),
raw_rc_count(0),
_failsafe_pwm{0},
_disarmed_pwm{0},
_reverse_pwm_mask(0),
_num_failsafe_set(0),
_num_disarmed_set(0),
_safety_off(false),
_safety_disabled(false),
_to_safety(nullptr),
_to_mixer_status(nullptr),
_mot_t_max(0.0f),
_thr_mdl_fac(0.0f),
_airmode(false),
_motor_ordering(MotorOrdering::PX4),
_perf_control_latency(perf_alloc(PC_ELAPSED, "fmu control latency"))
{
for (unsigned i = 0; i < _max_actuators; i++) {
_min_pwm[i] = PWM_DEFAULT_MIN;
_max_pwm[i] = PWM_DEFAULT_MAX;
}
_control_topics[0] = ORB_ID(actuator_controls_0);
_control_topics[1] = ORB_ID(actuator_controls_1);
_control_topics[2] = ORB_ID(actuator_controls_2);
_control_topics[3] = ORB_ID(actuator_controls_3);
memset(_controls, 0, sizeof(_controls));
memset(_poll_fds, 0, sizeof(_poll_fds));
// Safely initialize armed flags.
_armed.armed = false;
_armed.prearmed = false;
_armed.ready_to_arm = false;
_armed.lockdown = false;
_armed.force_failsafe = false;
_armed.in_esc_calibration_mode = false;
// rc input, published to ORB
_rc_in.input_source = input_rc_s::RC_INPUT_SOURCE_PX4FMU_PPM;
// initialize it as RC lost
_rc_in.rc_lost = true;
// initialize raw_rc values and count
for (unsigned i = 0; i < input_rc_s::RC_INPUT_MAX_CHANNELS; i++) {
raw_rc_values[i] = UINT16_MAX;
}
raw_rc_count = 0;
// If there is no safety button, disable it on boot.
#ifndef GPIO_BTN_SAFETY
_safety_off = true;
#endif
/* only enable this during development */
_debug_enabled = false;
}
PX4FMU::~PX4FMU()
{
for (unsigned i = 0; i < actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS; i++) {
if (_control_subs[i] > 0) {
orb_unsubscribe(_control_subs[i]);
_control_subs[i] = -1;
}
}
orb_unsubscribe(_armed_sub);
orb_unsubscribe(_param_sub);
orb_unadvertise(_to_input_rc);
orb_unadvertise(_outputs_pub);
orb_unadvertise(_to_safety);
orb_unadvertise(_to_mixer_status);
/* make sure servos are off */
up_pwm_servo_deinit();
#ifdef RC_SERIAL_PORT
dsm_deinit();
#endif
/* note - someone else is responsible for restoring the GPIO config */
/* clean up the alternate device node */
unregister_class_devname(PWM_OUTPUT_BASE_DEVICE_PATH, _class_instance);
perf_free(_perf_control_latency);
}
int
PX4FMU::init()
{
int ret;
/* do regular cdev init */
ret = CDev::init();
if (ret != OK) {
return ret;
}
// XXX best would be to register / de-register the device depending on modes
/* try to claim the generic PWM output device node as well - it's OK if we fail at this */
_class_instance = register_class_devname(PWM_OUTPUT_BASE_DEVICE_PATH);
if (_class_instance == CLASS_DEVICE_PRIMARY) {
/* lets not be too verbose */
} else if (_class_instance < 0) {
PX4_ERR("FAILED registering class device");
}
_safety_disabled = circuit_breaker_enabled("CBRK_IO_SAFETY", CBRK_IO_SAFETY_KEY);
/* force a reset of the update rate */
_current_update_rate = 0;
_armed_sub = orb_subscribe(ORB_ID(actuator_armed));
_param_sub = orb_subscribe(ORB_ID(parameter_update));
_adc_sub = orb_subscribe(ORB_ID(adc_report));
/* initialize PWM limit lib */
pwm_limit_init(&_pwm_limit);
update_pwm_rev_mask();
#ifdef RC_SERIAL_PORT
# ifdef RF_RADIO_POWER_CONTROL
// power radio on
RF_RADIO_POWER_CONTROL(true);
# endif
_vehicle_cmd_sub = orb_subscribe(ORB_ID(vehicle_command));
// dsm_init sets some file static variables and returns a file descriptor
_rcs_fd = dsm_init(RC_SERIAL_PORT);
// assume SBUS input
sbus_config(_rcs_fd, board_supports_single_wire());
# ifdef GPIO_PPM_IN
// disable CPPM input by mapping it away from the timer capture input
px4_arch_unconfiggpio(GPIO_PPM_IN);
# endif
#endif
// Getting initial parameter values
update_params();
for (unsigned i = 0; i < _max_actuators; i++) {
char pname[16];
sprintf(pname, "PWM_AUX_TRIM%d", i + 1);
param_find(pname);
}
return 0;
}
void
PX4FMU::safety_check_button(void)
{
#ifdef GPIO_BTN_SAFETY
static int counter = 0;
/*
* Debounce the safety button, change state if it has been held for long enough.
*
*/
bool safety_button_pressed = px4_arch_gpioread(GPIO_BTN_SAFETY);
/*
* Keep pressed for a while to arm.
*
* Note that the counting sequence has to be same length
* for arming / disarming in order to end up as proper
* state machine, keep ARM_COUNTER_THRESHOLD the same
* length in all cases of the if/else struct below.
*/
if (safety_button_pressed && !_safety_off) {
if (counter < CYCLE_COUNT) {
counter++;
} else if (counter == CYCLE_COUNT) {
/* switch to armed state */
_safety_off = true;
counter++;
}
} else if (safety_button_pressed && _safety_off) {
if (counter < CYCLE_COUNT) {
counter++;
} else if (counter == CYCLE_COUNT) {
/* change to disarmed state and notify the FMU */
_safety_off = false;
counter++;
}
} else {
counter = 0;
}
#endif
}
void
PX4FMU::flash_safety_button()
{
#ifdef GPIO_BTN_SAFETY
/* Select the appropriate LED flash pattern depending on the current arm state */
uint16_t pattern = LED_PATTERN_FMU_REFUSE_TO_ARM;
/* cycle the blink state machine at 10Hz */
static int blink_counter = 0;
if (_safety_off) {
if (_armed.armed) {
pattern = LED_PATTERN_IO_FMU_ARMED;
} else {
pattern = LED_PATTERN_IO_ARMED;
}
} else if (_armed.armed) {
pattern = LED_PATTERN_FMU_ARMED;
} else {
pattern = LED_PATTERN_FMU_OK_TO_ARM;
}
/* Turn the LED on if we have a 1 at the current bit position */
px4_arch_gpiowrite(GPIO_LED_SAFETY, !(pattern & (1 << blink_counter++)));
if (blink_counter > 15) {
blink_counter = 0;
}
#endif
}
int
PX4FMU::set_mode(Mode mode)
{
unsigned old_mask = _pwm_mask;
/*
* Configure for PWM output.
*
* Note that regardless of the configured mode, the task is always
* listening and mixing; the mode just selects which of the channels
* are presented on the output pins.
*/
switch (mode) {
case MODE_1PWM:
/* default output rates */
_pwm_default_rate = 50;
_pwm_alt_rate = 50;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0x1;
_pwm_initialized = false;
_num_outputs = 1;
break;
#if defined(BOARD_HAS_CAPTURE)
case MODE_2PWM2CAP: // v1 multi-port with flow control lines as PWM
up_input_capture_set(2, Rising, 0, NULL, NULL);
up_input_capture_set(3, Rising, 0, NULL, NULL);
DEVICE_DEBUG("MODE_2PWM2CAP");
#endif
/* FALLTHROUGH */
case MODE_2PWM: // v1 multi-port with flow control lines as PWM
DEVICE_DEBUG("MODE_2PWM");
/* default output rates */
_pwm_default_rate = 50;
_pwm_alt_rate = 50;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0x3;
_pwm_initialized = false;
_num_outputs = 2;
break;
#if defined(BOARD_HAS_CAPTURE)
case MODE_3PWM1CAP: // v1 multi-port with flow control lines as PWM
DEVICE_DEBUG("MODE_3PWM1CAP");
up_input_capture_set(3, Rising, 0, NULL, NULL);
#endif
/* FALLTHROUGH */
case MODE_3PWM: // v1 multi-port with flow control lines as PWM
DEVICE_DEBUG("MODE_3PWM");
/* default output rates */
_pwm_default_rate = 50;
_pwm_alt_rate = 50;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0x7;
_pwm_initialized = false;
_num_outputs = 3;
break;
case MODE_4PWM: // v1 or v2 multi-port as 4 PWM outs
DEVICE_DEBUG("MODE_4PWM");
/* default output rates */
_pwm_default_rate = 50;
_pwm_alt_rate = 50;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0xf;
_pwm_initialized = false;
_num_outputs = 4;
break;
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
case MODE_6PWM:
DEVICE_DEBUG("MODE_6PWM");
/* default output rates */
_pwm_default_rate = 50;
_pwm_alt_rate = 50;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0x3f;
_pwm_initialized = false;
_num_outputs = 6;
break;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
case MODE_8PWM: // AeroCore PWMs as 8 PWM outs
DEVICE_DEBUG("MODE_8PWM");
/* default output rates */
_pwm_default_rate = 50;
_pwm_alt_rate = 50;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0xff;
_pwm_initialized = false;
_num_outputs = 8;
break;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 14
case MODE_14PWM:
DEVICE_DEBUG("MODE_14PWM");
/* default output rates */
_pwm_default_rate = 50;
_pwm_alt_rate = 50;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0x3fff;
_pwm_initialized = false;
_num_outputs = 14;
break;
#endif
case MODE_NONE:
DEVICE_DEBUG("MODE_NONE");
_pwm_default_rate = 10; /* artificially reduced output rate */
_pwm_alt_rate = 10;
_pwm_alt_rate_channels = 0;
_pwm_mask = 0x0;
_pwm_initialized = false;
_num_outputs = 0;
if (old_mask != _pwm_mask) {
/* disable servo outputs - no need to set rates */
up_pwm_servo_deinit();
}
break;
default:
return -EINVAL;
}
_mode = mode;
return OK;
}
/* When set_pwm_rate is called from either of the 2 IOCTLs:
*
* PWM_SERVO_SET_UPDATE_RATE - Sets the "alternate" channel's rate to the callers's rate specified
* and the non "alternate" channels to the _pwm_default_rate.
*
* rate_map = _pwm_alt_rate_channels
* default_rate = _pwm_default_rate
* alt_rate = arg of IOCTL (see rates)
*
* PWM_SERVO_SET_SELECT_UPDATE_RATE - The caller's specified rate map selects the "alternate" channels
* to be set to the alt rate. (_pwm_alt_rate)
* All other channels are set to the default rate. (_pwm_default_rate)
*
* rate_map = arg of IOCTL
* default_rate = _pwm_default_rate
* alt_rate = _pwm_alt_rate
* rate_map - A mask of 1's for the channels to be set to the
* alternate rate.
* N.B. All channels is a given group must be set
* to the same rate/mode. (default or alt)
* rates:
* alt_rate, default_rate For PWM is 25 or 400Hz
* For Oneshot there is no rate, 0 is therefore used
* to select Oneshot mode
*/
int
PX4FMU::set_pwm_rate(uint32_t rate_map, unsigned default_rate, unsigned alt_rate)
{
PX4_DEBUG("set_pwm_rate %x %u %u", rate_map, default_rate, alt_rate);
for (unsigned pass = 0; pass < 2; pass++) {
/* We should note that group is iterated over from 0 to _max_actuators.
* This allows for the ideal worlds situation: 1 channel per group
* configuration.
*
* This is typically not what HW supports. A group represents a timer
* and channels belongs to a timer.
* Therefore all channels in a group are dependent on the timer's
* common settings and can not be independent in terms of count frequency
* (granularity of pulse width) and rate (period of repetition).
*
* To say it another way, all channels in a group moust have the same
* rate and mode. (See rates above.)
*/
for (unsigned group = 0; group < _max_actuators; group++) {
// get the channel mask for this rate group
uint32_t mask = up_pwm_servo_get_rate_group(group);
if (mask == 0) {
continue;
}
// all channels in the group must be either default or alt-rate
uint32_t alt = rate_map & mask;
if (pass == 0) {
// preflight
if ((alt != 0) && (alt != mask)) {
PX4_WARN("rate group %u mask %x bad overlap %x", group, mask, alt);
// not a legal map, bail
return -EINVAL;
}
} else {
// set it - errors here are unexpected
if (alt != 0) {
if (up_pwm_servo_set_rate_group_update(group, alt_rate) != OK) {
PX4_WARN("rate group set alt failed");
return -EINVAL;
}
} else {
if (up_pwm_servo_set_rate_group_update(group, default_rate) != OK) {
PX4_WARN("rate group set default failed");
return -EINVAL;
}
}
}
}
}
_pwm_alt_rate_channels = rate_map;
_pwm_default_rate = default_rate;
_pwm_alt_rate = alt_rate;
return OK;
}
int
PX4FMU::set_pwm_alt_rate(unsigned rate)
{
return set_pwm_rate(_pwm_alt_rate_channels, _pwm_default_rate, rate);
}
int
PX4FMU::set_pwm_alt_channels(uint32_t channels)
{
return set_pwm_rate(channels, _pwm_default_rate, _pwm_alt_rate);
}
int
PX4FMU::set_i2c_bus_clock(unsigned bus, unsigned clock_hz)
{
return device::I2C::set_bus_clock(bus, clock_hz);
}
void
PX4FMU::subscribe()
{
/* subscribe/unsubscribe to required actuator control groups */
uint32_t sub_groups = _groups_required & ~_groups_subscribed;
uint32_t unsub_groups = _groups_subscribed & ~_groups_required;
_poll_fds_num = 0;
for (unsigned i = 0; i < actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS; i++) {
if (sub_groups & (1 << i)) {
DEVICE_DEBUG("subscribe to actuator_controls_%d", i);
_control_subs[i] = orb_subscribe(_control_topics[i]);
}
if (unsub_groups & (1 << i)) {
DEVICE_DEBUG("unsubscribe from actuator_controls_%d", i);
orb_unsubscribe(_control_subs[i]);
_control_subs[i] = -1;
}
if (_control_subs[i] > 0) {
_poll_fds[_poll_fds_num].fd = _control_subs[i];
_poll_fds[_poll_fds_num].events = POLLIN;
_poll_fds_num++;
}
}
}
void
PX4FMU::update_pwm_rev_mask()
{
_reverse_pwm_mask = 0;
for (unsigned i = 0; i < _max_actuators; i++) {
char pname[16];
int32_t ival;
/* fill the channel reverse mask from parameters */
sprintf(pname, "PWM_AUX_REV%d", i + 1);
param_t param_h = param_find(pname);
if (param_h != PARAM_INVALID) {
param_get(param_h, &ival);
_reverse_pwm_mask |= ((int16_t)(ival != 0)) << i;
}
}
}
void
PX4FMU::update_pwm_trims()
{
PX4_DEBUG("update_pwm_trims");
if (_mixers != nullptr) {
int16_t values[_max_actuators] = {};
for (unsigned i = 0; i < _max_actuators; i++) {
char pname[16];
float pval;
/* fill the struct from parameters */
sprintf(pname, "PWM_AUX_TRIM%d", i + 1);
param_t param_h = param_find(pname);
if (param_h != PARAM_INVALID) {
param_get(param_h, &pval);
values[i] = (int16_t)(10000 * pval);
PX4_DEBUG("%s: %d", pname, values[i]);
}
}
/* copy the trim values to the mixer offsets */
unsigned n_out = _mixers->set_trims(values, _max_actuators);
PX4_DEBUG("set %d trims", n_out);
}
}
int
PX4FMU::task_spawn(int argc, char *argv[])
{
bool run_as_task = false;
bool error_flag = false;
int myoptind = 1;
int ch;
const char *myoptarg = nullptr;
while ((ch = px4_getopt(argc, argv, "t", &myoptind, &myoptarg)) != EOF) {
switch (ch) {
case 't':
run_as_task = true;
break;
case '?':
error_flag = true;
break;
default:
PX4_WARN("unrecognized flag");
error_flag = true;
break;
}
}
if (error_flag) {
return -1;
}
if (!run_as_task) {
/* schedule a cycle to start things */
int ret = work_queue(HPWORK, &_work, (worker_t)&PX4FMU::cycle_trampoline, nullptr, 0);
if (ret < 0) {
return ret;
}
_task_id = task_id_is_work_queue;
} else {
/* start the IO interface task */
_task_id = px4_task_spawn_cmd("fmu",
SCHED_DEFAULT,
SCHED_PRIORITY_ACTUATOR_OUTPUTS,
1340,
(px4_main_t)&run_trampoline,
nullptr);
if (_task_id < 0) {
_task_id = -1;
return -errno;
}
}
// wait until task is up & running (the mode_* commands depend on it)
if (wait_until_running() < 0) {
_task_id = -1;
return -1;
}
return PX4_OK;
}
void
PX4FMU::cycle_trampoline(void *arg)
{
PX4FMU *dev = reinterpret_cast<PX4FMU *>(arg);
// check if the trampoline is called for the first time
if (!dev) {
dev = new PX4FMU(false);
if (!dev) {
PX4_ERR("alloc failed");
return;
}
if (dev->init() != 0) {
PX4_ERR("init failed");
delete dev;
return;
}
_object = dev;
}
dev->cycle();
}
void
PX4FMU::capture_trampoline(void *context, uint32_t chan_index,
hrt_abstime edge_time, uint32_t edge_state, uint32_t overflow)
{
PX4FMU *dev = reinterpret_cast<PX4FMU *>(context);
dev->capture_callback(chan_index, edge_time, edge_state, overflow);
}
void
PX4FMU::capture_callback(uint32_t chan_index,
hrt_abstime edge_time, uint32_t edge_state, uint32_t overflow)
{
fprintf(stdout, "FMU: Capture chan:%d time:%lld state:%d overflow:%d\n", chan_index, edge_time, edge_state, overflow);
}
void
PX4FMU::fill_rc_in(uint16_t raw_rc_count_local,
uint16_t raw_rc_values_local[input_rc_s::RC_INPUT_MAX_CHANNELS],
hrt_abstime now, bool frame_drop, bool failsafe,
unsigned frame_drops, int rssi = -1)
{
// fill rc_in struct for publishing
_rc_in.channel_count = raw_rc_count_local;
if (_rc_in.channel_count > input_rc_s::RC_INPUT_MAX_CHANNELS) {
_rc_in.channel_count = input_rc_s::RC_INPUT_MAX_CHANNELS;
}
unsigned valid_chans = 0;
for (unsigned i = 0; i < _rc_in.channel_count; i++) {
_rc_in.values[i] = raw_rc_values_local[i];
if (raw_rc_values_local[i] != UINT16_MAX) {
valid_chans++;
}
// once filled, reset values back to default
raw_rc_values[i] = UINT16_MAX;
}
_rc_in.timestamp = now;
_rc_in.timestamp_last_signal = _rc_in.timestamp;
_rc_in.rc_ppm_frame_length = 0;
/* fake rssi if no value was provided */
if (rssi == -1) {
/* set RSSI if analog RSSI input is present */
if (_analog_rc_rssi_stable) {
float rssi_analog = ((_analog_rc_rssi_volt - 0.2f) / 3.0f) * 100.0f;
if (rssi_analog > 100.0f) {
rssi_analog = 100.0f;
}
if (rssi_analog < 0.0f) {
rssi_analog = 0.0f;
}
_rc_in.rssi = rssi_analog;
} else {
_rc_in.rssi = 255;
}
} else {
_rc_in.rssi = rssi;
}
if (valid_chans == 0) {
_rc_in.rssi = 0;
}
_rc_in.rc_failsafe = failsafe;
_rc_in.rc_lost = (valid_chans == 0);
_rc_in.rc_lost_frame_count = frame_drops;
_rc_in.rc_total_frame_count = 0;
}
#ifdef RC_SERIAL_PORT
void PX4FMU::set_rc_scan_state(RC_SCAN newState)
{
// PX4_WARN("RCscan: %s failed, trying %s", PX4FMU::RC_SCAN_STRING[_rc_scan_state], PX4FMU::RC_SCAN_STRING[newState]);
_rc_scan_begin = 0;
_rc_scan_state = newState;
}
void PX4FMU::rc_io_invert(bool invert, uint32_t uxart_base)
{
INVERT_RC_INPUT(invert, uxart_base);
}
#endif
void
PX4FMU::update_pwm_out_state(bool on)
{
if (on && !_pwm_initialized && _pwm_mask != 0) {
up_pwm_servo_init(_pwm_mask);
set_pwm_rate(_pwm_alt_rate_channels, _pwm_default_rate, _pwm_alt_rate);
_pwm_initialized = true;
}
up_pwm_servo_arm(on);
}
void
PX4FMU::run()
{
if (init() != 0) {
PX4_ERR("init failed");
exit_and_cleanup();
return;
}
cycle();
}
void
PX4FMU::cycle()
{
while (true) {
if (_groups_subscribed != _groups_required) {
subscribe();
_groups_subscribed = _groups_required;
/* force setting update rate */
_current_update_rate = 0;
}
int poll_timeout = 5; // needs to be small enough so that we don't miss RC input data
if (!_run_as_task) {
/*
* Adjust actuator topic update rate to keep up with
* the highest servo update rate configured.
*
* We always mix at max rate; some channels may update slower.
*/
unsigned max_rate = (_pwm_default_rate > _pwm_alt_rate) ? _pwm_default_rate : _pwm_alt_rate;
if (_current_update_rate != max_rate) {
_current_update_rate = max_rate;
int update_rate_in_ms = int(1000 / _current_update_rate);
/* reject faster than 500 Hz updates */
if (update_rate_in_ms < 2) {
update_rate_in_ms = 2;
}
/* reject slower than 10 Hz updates */
if (update_rate_in_ms > 100) {
update_rate_in_ms = 100;
}
PX4_DEBUG("adjusted actuator update interval to %ums", update_rate_in_ms);
for (unsigned i = 0; i < actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS; i++) {
if (_control_subs[i] > 0) {
orb_set_interval(_control_subs[i], update_rate_in_ms);
}
}
// set to current max rate, even if we are actually checking slower/faster
_current_update_rate = max_rate;
}
/* check if anything updated */
poll_timeout = 0;
}
/* wait for an update */
unsigned n_updates = 0;
int ret = px4_poll(_poll_fds, _poll_fds_num, poll_timeout);
/* this would be bad... */
if (ret < 0) {
DEVICE_LOG("poll error %d", errno);
} else if (ret == 0) {
/* timeout: no control data, switch to failsafe values */
// PX4_WARN("no PWM: failsafe");
} else {
if (_mixers != nullptr) {
/* get controls for required topics */
unsigned poll_id = 0;
for (unsigned i = 0; i < actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS; i++) {
if (_control_subs[i] > 0) {
if (_poll_fds[poll_id].revents & POLLIN) {
if (i == 0) {
n_updates++;
}
orb_copy(_control_topics[i], _control_subs[i], &_controls[i]);
}
poll_id++;
}
/* During ESC calibration, we overwrite the throttle value. */
if (i == 0 && _armed.in_esc_calibration_mode) {
/* Set all controls to 0 */
memset(&_controls[i], 0, sizeof(_controls[i]));
/* except thrust to maximum. */
_controls[i].control[actuator_controls_s::INDEX_THROTTLE] = 1.0f;
/* Switch off the PWM limit ramp for the calibration. */
_pwm_limit.state = PWM_LIMIT_STATE_ON;
}
}
}
} // poll_fds
/* run the mixers on every cycle */
{
if (_mixers != nullptr) {
if (_mot_t_max > FLT_EPSILON) {
hrt_abstime now = hrt_absolute_time();
float dt = (now - _time_last_mix) / 1e6f;
_time_last_mix = now;
if (dt < 0.0001f) {
dt = 0.0001f;
} else if (dt > 0.02f) {
dt = 0.02f;
}
// maximum value the outputs of the multirotor mixer are allowed to change in this cycle
// factor 2 is needed because actuator outputs are in the range [-1,1]
const float delta_out_max = 2.0f * 1000.0f * dt / (_max_pwm[0] - _min_pwm[0]) / _mot_t_max;
_mixers->set_max_delta_out_once(delta_out_max);
}
if (_thr_mdl_fac > FLT_EPSILON) {
_mixers->set_thrust_factor(_thr_mdl_fac);
}
/* do mixing */
float outputs[_max_actuators];
const unsigned mixed_num_outputs = _mixers->mix(outputs, _num_outputs);
/* the PWM limit call takes care of out of band errors, NaN and constrains */
uint16_t pwm_limited[MAX_ACTUATORS];
pwm_limit_calc(_throttle_armed, arm_nothrottle(), mixed_num_outputs, _reverse_pwm_mask,
_disarmed_pwm, _min_pwm, _max_pwm, outputs, pwm_limited, &_pwm_limit);
/* overwrite outputs in case of force_failsafe with _failsafe_pwm PWM values */
if (_armed.force_failsafe) {
for (size_t i = 0; i < mixed_num_outputs; i++) {
pwm_limited[i] = _failsafe_pwm[i];
}
}
/* overwrite outputs in case of lockdown with disarmed PWM values */
if (_armed.lockdown || _armed.manual_lockdown) {
for (size_t i = 0; i < mixed_num_outputs; i++) {
pwm_limited[i] = _disarmed_pwm[i];
}
}
/* apply _motor_ordering */
reorder_outputs(pwm_limited);
/* output to the servos */
if (_pwm_initialized) {
for (size_t i = 0; i < mixed_num_outputs; i++) {
up_pwm_servo_set(i, pwm_limited[i]);
}
}
/* Trigger all timer's channels in Oneshot mode to fire
* the oneshots with updated values.
*/
if (n_updates > 0) {
up_pwm_update();
}
actuator_outputs_s actuator_outputs = {};
actuator_outputs.timestamp = hrt_absolute_time();
actuator_outputs.noutputs = mixed_num_outputs;
// zero unused outputs
for (size_t i = 0; i < mixed_num_outputs; ++i) {
actuator_outputs.output[i] = pwm_limited[i];
}
orb_publish_auto(ORB_ID(actuator_outputs), &_outputs_pub, &actuator_outputs, &_class_instance, ORB_PRIO_DEFAULT);
/* publish mixer status */
MultirotorMixer::saturation_status saturation_status;
saturation_status.value = _mixers->get_saturation_status();
if (saturation_status.flags.valid) {
multirotor_motor_limits_s motor_limits;
motor_limits.timestamp = hrt_absolute_time();
motor_limits.saturation_status = saturation_status.value;
orb_publish_auto(ORB_ID(multirotor_motor_limits), &_to_mixer_status, &motor_limits, &_class_instance, ORB_PRIO_DEFAULT);
}
_mixers->set_airmode(_airmode);
// use first valid timestamp_sample for latency tracking
for (int i = 0; i < actuator_controls_s::NUM_ACTUATOR_CONTROL_GROUPS; i++) {
const bool required = _groups_required & (1 << i);
const hrt_abstime &timestamp_sample = _controls[i].timestamp_sample;
if (required && (timestamp_sample > 0)) {
perf_set_elapsed(_perf_control_latency, actuator_outputs.timestamp - timestamp_sample);
break;
}
}
}
}
_cycle_timestamp = hrt_absolute_time();
#ifdef GPIO_BTN_SAFETY
if (_cycle_timestamp - _last_safety_check >= (unsigned int)1e5) {
_last_safety_check = _cycle_timestamp;
/**
* Get and handle the safety status at 10Hz
*/
struct safety_s safety = {};
if (_safety_disabled) {
_safety_off = true;
} else {
/* read safety switch input and control safety switch LED at 10Hz */
safety_check_button();
}
/* Make the safety button flash anyway, no matter if it's used or not. */
flash_safety_button();
safety.timestamp = hrt_absolute_time();
if (_safety_off) {
safety.safety_off = true;
safety.safety_switch_available = true;
} else {
safety.safety_off = false;
safety.safety_switch_available = true;
}
/* lazily publish the safety status */
if (_to_safety != nullptr) {
orb_publish(ORB_ID(safety), _to_safety, &safety);
} else {
int instance = _class_instance;
_to_safety = orb_advertise_multi(ORB_ID(safety), &safety, &instance, ORB_PRIO_DEFAULT);
}
}
#endif
/* check arming state */
bool updated = false;
orb_check(_armed_sub, &updated);
if (updated) {
orb_copy(ORB_ID(actuator_armed), _armed_sub, &_armed);
/* Update the armed status and check that we're not locked down.
* We also need to arm throttle for the ESC calibration. */
_throttle_armed = (_safety_off && _armed.armed && !_armed.lockdown) ||
(_safety_off && _armed.in_esc_calibration_mode);
}
/* update PWM status if armed or if disarmed PWM values are set */
bool pwm_on = _armed.armed || _num_disarmed_set > 0 || _armed.in_esc_calibration_mode;
if (_pwm_on != pwm_on) {
_pwm_on = pwm_on;
update_pwm_out_state(pwm_on);
}
#ifdef RC_SERIAL_PORT
/* vehicle command */
orb_check(_vehicle_cmd_sub, &updated);
if (updated) {
struct vehicle_command_s cmd;
orb_copy(ORB_ID(vehicle_command), _vehicle_cmd_sub, &cmd);
// Check for a pairing command
if ((unsigned int)cmd.command == vehicle_command_s::VEHICLE_CMD_START_RX_PAIR) {
if (!_armed.armed) {
if ((int)cmd.param1 == 0) {
// DSM binding command
int dsm_bind_mode = (int)cmd.param2;
int dsm_bind_pulses = 0;
if (dsm_bind_mode == 0) {
dsm_bind_pulses = DSM2_BIND_PULSES;
} else if (dsm_bind_mode == 1) {
dsm_bind_pulses = DSMX_BIND_PULSES;
} else {
dsm_bind_pulses = DSMX8_BIND_PULSES;
}
ioctl(nullptr, DSM_BIND_START, dsm_bind_pulses);
}
} else {
PX4_WARN("system armed, bind request rejected");
}
}
}
#endif
orb_check(_param_sub, &updated);
if (updated) {
this->update_params();
}
/* update ADC sampling */
#ifdef ADC_RC_RSSI_CHANNEL
orb_check(_adc_sub, &updated);
if (updated) {
struct adc_report_s adc;
orb_copy(ORB_ID(adc_report), _adc_sub, &adc);
const unsigned adc_chans = sizeof(adc.channel_id) / sizeof(adc.channel_id[0]);
for (unsigned i = 0; i < adc_chans; i++) {
if (adc.channel_id[i] == ADC_RC_RSSI_CHANNEL) {
if (_analog_rc_rssi_volt < 0.0f) {
_analog_rc_rssi_volt = adc.channel_value[i];
}
_analog_rc_rssi_volt = _analog_rc_rssi_volt * 0.995f + adc.channel_value[i] * 0.005f;
/* only allow this to be used if we see a high RSSI once */
if (_analog_rc_rssi_volt > 2.5f) {
_analog_rc_rssi_stable = true;
}
}
}
}
#endif
bool rc_updated = false;
#ifdef RC_SERIAL_PORT
// This block scans for a supported serial RC input and locks onto the first one found
// Scan for 300 msec, then switch protocol
constexpr hrt_abstime rc_scan_max = 300 * 1000;
bool sbus_failsafe, sbus_frame_drop;
unsigned frame_drops;
bool dsm_11_bit;
if (_report_lock && _rc_scan_locked) {
_report_lock = false;
//PX4_WARN("RCscan: %s RC input locked", RC_SCAN_STRING[_rc_scan_state]);
}
// read all available data from the serial RC input UART
int newBytes = ::read(_rcs_fd, &_rcs_buf[0], SBUS_BUFFER_SIZE);
switch (_rc_scan_state) {
case RC_SCAN_SBUS:
if (_rc_scan_begin == 0) {
_rc_scan_begin = _cycle_timestamp;
// Configure serial port for SBUS
sbus_config(_rcs_fd, board_supports_single_wire());
rc_io_invert(true, RC_UXART_BASE);
} else if (_rc_scan_locked
|| _cycle_timestamp - _rc_scan_begin < rc_scan_max) {
// parse new data
if (newBytes > 0) {
rc_updated = sbus_parse(_cycle_timestamp, &_rcs_buf[0], newBytes, &raw_rc_values[0], &raw_rc_count, &sbus_failsafe,
&sbus_frame_drop, &frame_drops, input_rc_s::RC_INPUT_MAX_CHANNELS);
if (rc_updated) {
// we have a new SBUS frame. Publish it.
_rc_in.input_source = input_rc_s::RC_INPUT_SOURCE_PX4FMU_SBUS;
fill_rc_in(raw_rc_count, raw_rc_values, _cycle_timestamp,
sbus_frame_drop, sbus_failsafe, frame_drops);
_rc_scan_locked = true;
}
}
} else {
// Scan the next protocol
set_rc_scan_state(RC_SCAN_DSM);
}
break;
case RC_SCAN_DSM:
if (_rc_scan_begin == 0) {
_rc_scan_begin = _cycle_timestamp;
// // Configure serial port for DSM
dsm_config(_rcs_fd);
rc_io_invert(false, RC_UXART_BASE);
} else if (_rc_scan_locked
|| _cycle_timestamp - _rc_scan_begin < rc_scan_max) {
if (newBytes > 0) {
// parse new data
rc_updated = dsm_parse(_cycle_timestamp, &_rcs_buf[0], newBytes, &raw_rc_values[0], &raw_rc_count,
&dsm_11_bit, &frame_drops, input_rc_s::RC_INPUT_MAX_CHANNELS);
if (rc_updated) {
// we have a new DSM frame. Publish it.
_rc_in.input_source = input_rc_s::RC_INPUT_SOURCE_PX4FMU_DSM;
fill_rc_in(raw_rc_count, raw_rc_values, _cycle_timestamp,
false, false, frame_drops);
_rc_scan_locked = true;
}
}
} else {
// Scan the next protocol
set_rc_scan_state(RC_SCAN_ST24);
}
break;
case RC_SCAN_ST24:
if (_rc_scan_begin == 0) {
_rc_scan_begin = _cycle_timestamp;
// Configure serial port for DSM
dsm_config(_rcs_fd);
rc_io_invert(false, RC_UXART_BASE);
} else if (_rc_scan_locked
|| _cycle_timestamp - _rc_scan_begin < rc_scan_max) {
if (newBytes > 0) {
// parse new data
uint8_t st24_rssi, lost_count;
rc_updated = false;
for (unsigned i = 0; i < (unsigned)newBytes; i++) {
/* set updated flag if one complete packet was parsed */
st24_rssi = RC_INPUT_RSSI_MAX;
rc_updated = (OK == st24_decode(_rcs_buf[i], &st24_rssi, &lost_count,
&raw_rc_count, raw_rc_values, input_rc_s::RC_INPUT_MAX_CHANNELS));
}
// The st24 will keep outputting RC channels and RSSI even if RC has been lost.
// The only way to detect RC loss is therefore to look at the lost_count.
if (rc_updated) {
if (lost_count == 0) {
// we have a new ST24 frame. Publish it.
_rc_in.input_source = input_rc_s::RC_INPUT_SOURCE_PX4FMU_ST24;
fill_rc_in(raw_rc_count, raw_rc_values, _cycle_timestamp,
false, false, frame_drops, st24_rssi);
_rc_scan_locked = true;
} else {
// if the lost count > 0 means that there is an RC loss
_rc_in.rc_lost = true;
}
}
}
} else {
// Scan the next protocol
set_rc_scan_state(RC_SCAN_SUMD);
}
break;
case RC_SCAN_SUMD:
if (_rc_scan_begin == 0) {
_rc_scan_begin = _cycle_timestamp;
// Configure serial port for DSM
dsm_config(_rcs_fd);
rc_io_invert(false, RC_UXART_BASE);
} else if (_rc_scan_locked
|| _cycle_timestamp - _rc_scan_begin < rc_scan_max) {
if (newBytes > 0) {
// parse new data
uint8_t sumd_rssi, rx_count;
bool sumd_failsafe;
rc_updated = false;
for (unsigned i = 0; i < (unsigned)newBytes; i++) {
/* set updated flag if one complete packet was parsed */
sumd_rssi = RC_INPUT_RSSI_MAX;
rc_updated = (OK == sumd_decode(_rcs_buf[i], &sumd_rssi, &rx_count,
&raw_rc_count, raw_rc_values, input_rc_s::RC_INPUT_MAX_CHANNELS, &sumd_failsafe));
}
if (rc_updated) {
// we have a new SUMD frame. Publish it.
_rc_in.input_source = input_rc_s::RC_INPUT_SOURCE_PX4FMU_SUMD;
fill_rc_in(raw_rc_count, raw_rc_values, _cycle_timestamp,
false, sumd_failsafe, frame_drops, sumd_rssi);
_rc_scan_locked = true;
}
}
} else {
// Scan the next protocol
set_rc_scan_state(RC_SCAN_PPM);
}
break;
case RC_SCAN_PPM:
// skip PPM if it's not supported
#ifdef HRT_PPM_CHANNEL
if (_rc_scan_begin == 0) {
_rc_scan_begin = _cycle_timestamp;
// Configure timer input pin for CPPM
px4_arch_configgpio(GPIO_PPM_IN);
rc_io_invert(false, RC_UXART_BASE);
} else if (_rc_scan_locked || _cycle_timestamp - _rc_scan_begin < rc_scan_max) {
// see if we have new PPM input data
if ((ppm_last_valid_decode != _rc_in.timestamp_last_signal) && ppm_decoded_channels > 3) {
// we have a new PPM frame. Publish it.
rc_updated = true;
_rc_in.input_source = input_rc_s::RC_INPUT_SOURCE_PX4FMU_PPM;
fill_rc_in(ppm_decoded_channels, ppm_buffer, _cycle_timestamp, false, false, 0);
_rc_scan_locked = true;
_rc_in.rc_ppm_frame_length = ppm_frame_length;
_rc_in.timestamp_last_signal = ppm_last_valid_decode;
}
} else {
// disable CPPM input by mapping it away from the timer capture input
px4_arch_unconfiggpio(GPIO_PPM_IN);
// Scan the next protocol
set_rc_scan_state(RC_SCAN_SBUS);
}
#else // skip PPM if it's not supported
set_rc_scan_state(RC_SCAN_SBUS);
#endif // HRT_PPM_CHANNEL
break;
}
#else // RC_SERIAL_PORT not defined
#ifdef HRT_PPM_CHANNEL
// see if we have new PPM input data
if ((ppm_last_valid_decode != _rc_in.timestamp_last_signal) && ppm_decoded_channels > 3) {
// we have a new PPM frame. Publish it.
rc_updated = true;
fill_rc_in(ppm_decoded_channels, ppm_buffer, _cycle_timestamp, false, false, 0);
_rc_in.rc_ppm_frame_length = ppm_frame_length;
_rc_in.timestamp_last_signal = ppm_last_valid_decode;
}
#endif // HRT_PPM_CHANNEL
#endif // RC_SERIAL_PORT
if (rc_updated) {
/* lazily advertise on first publication */
if (_to_input_rc == nullptr) {
int instance = _class_instance;
_to_input_rc = orb_advertise_multi(ORB_ID(input_rc), &_rc_in, &instance, ORB_PRIO_DEFAULT);
} else {
orb_publish(ORB_ID(input_rc), _to_input_rc, &_rc_in);
}
} else if (!rc_updated && ((hrt_absolute_time() - _rc_in.timestamp_last_signal) > 1000 * 1000)) {
_rc_scan_locked = false;
}
if (_run_as_task) {
if (should_exit()) {
break;
}
} else {
if (should_exit()) {
exit_and_cleanup();
} else {
/* schedule next cycle */
work_queue(HPWORK, &_work, (worker_t)&PX4FMU::cycle_trampoline, this, USEC2TICK(SCHEDULE_INTERVAL));
}
break;
}
}
}
void PX4FMU::update_params()
{
parameter_update_s pupdate;
orb_copy(ORB_ID(parameter_update), _param_sub, &pupdate);
update_pwm_rev_mask();
update_pwm_trims();
param_t param_handle;
// maximum motor slew rate parameter
param_handle = param_find("MOT_SLEW_MAX");
if (param_handle != PARAM_INVALID) {
param_get(param_handle, &_mot_t_max);
}
// thrust to pwm modelling factor
param_handle = param_find("THR_MDL_FAC");
if (param_handle != PARAM_INVALID) {
param_get(param_handle, &_thr_mdl_fac);
}
// multicopter air-mode
param_handle = param_find("MC_AIRMODE");
if (param_handle != PARAM_INVALID) {
int32_t val;
param_get(param_handle, &val);
_airmode = val > 0;
PX4_DEBUG("%s: %d", "MC_AIRMODE", _airmode);
}
// motor ordering
param_handle = param_find("MOT_ORDERING");
if (param_handle != PARAM_INVALID) {
param_get(param_handle, (int32_t *)&_motor_ordering);
}
}
int
PX4FMU::control_callback(uintptr_t handle,
uint8_t control_group,
uint8_t control_index,
float &input)
{
const actuator_controls_s *controls = (actuator_controls_s *)handle;
input = controls[control_group].control[control_index];
/* limit control input */
if (input > 1.0f) {
input = 1.0f;
} else if (input < -1.0f) {
input = -1.0f;
}
/* motor spinup phase - lock throttle to zero */
if (_pwm_limit.state == PWM_LIMIT_STATE_RAMP) {
if ((control_group == actuator_controls_s::GROUP_INDEX_ATTITUDE ||
control_group == actuator_controls_s::GROUP_INDEX_ATTITUDE_ALTERNATE) &&
control_index == actuator_controls_s::INDEX_THROTTLE) {
/* limit the throttle output to zero during motor spinup,
* as the motors cannot follow any demand yet
*/
input = 0.0f;
}
}
/* throttle not arming - mark throttle input as invalid */
if (arm_nothrottle() && !_armed.in_esc_calibration_mode) {
if ((control_group == actuator_controls_s::GROUP_INDEX_ATTITUDE ||
control_group == actuator_controls_s::GROUP_INDEX_ATTITUDE_ALTERNATE) &&
control_index == actuator_controls_s::INDEX_THROTTLE) {
/* set the throttle to an invalid value */
input = NAN;
}
}
return 0;
}
int
PX4FMU::ioctl(file *filp, int cmd, unsigned long arg)
{
int ret;
/* try it as a GPIO ioctl first */
ret = gpio_ioctl(filp, cmd, arg);
if (ret != -ENOTTY) {
return ret;
}
/* try it as a Capture ioctl next */
ret = capture_ioctl(filp, cmd, arg);
if (ret != -ENOTTY) {
return ret;
}
/* if we are in valid PWM mode, try it as a PWM ioctl as well */
switch (_mode) {
case MODE_1PWM:
case MODE_2PWM:
case MODE_3PWM:
case MODE_4PWM:
case MODE_2PWM2CAP:
case MODE_3PWM1CAP:
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
case MODE_6PWM:
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
case MODE_8PWM:
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 14
case MODE_14PWM:
#endif
ret = pwm_ioctl(filp, cmd, arg);
break;
default:
PX4_DEBUG("not in a PWM mode");
break;
}
/* if nobody wants it, let CDev have it */
if (ret == -ENOTTY) {
ret = CDev::ioctl(filp, cmd, arg);
}
return ret;
}
int
PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg)
{
int ret = OK;
PX4_DEBUG("fmu ioctl cmd: %d, arg: %ld", cmd, arg);
lock();
switch (cmd) {
case PWM_SERVO_ARM:
update_pwm_out_state(true);
break;
case PWM_SERVO_SET_ARM_OK:
case PWM_SERVO_CLEAR_ARM_OK:
break;
case PWM_SERVO_SET_FORCE_SAFETY_OFF:
/* force safety switch off */
_safety_off = true;
break;
case PWM_SERVO_SET_FORCE_SAFETY_ON:
/* force safety switch on */
_safety_off = false;
break;
case PWM_SERVO_DISARM:
/* Ignore disarm if disarmed PWM is set already. */
if (_num_disarmed_set == 0) {
update_pwm_out_state(false);
}
break;
case PWM_SERVO_GET_DEFAULT_UPDATE_RATE:
*(uint32_t *)arg = _pwm_default_rate;
break;
case PWM_SERVO_SET_UPDATE_RATE:
ret = set_pwm_rate(_pwm_alt_rate_channels, _pwm_default_rate, arg);
break;
case PWM_SERVO_GET_UPDATE_RATE:
*(uint32_t *)arg = _pwm_alt_rate;
break;
case PWM_SERVO_SET_SELECT_UPDATE_RATE:
ret = set_pwm_rate(arg, _pwm_default_rate, _pwm_alt_rate);
break;
case PWM_SERVO_GET_SELECT_UPDATE_RATE:
*(uint32_t *)arg = _pwm_alt_rate_channels;
break;
case PWM_SERVO_SET_FAILSAFE_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
/* discard if too many values are sent */
if (pwm->channel_count > _max_actuators) {
ret = -EINVAL;
break;
}
for (unsigned i = 0; i < pwm->channel_count; i++) {
if (pwm->values[i] == 0) {
/* ignore 0 */
} else if (pwm->values[i] > PWM_HIGHEST_MAX) {
_failsafe_pwm[i] = PWM_HIGHEST_MAX;
}
#if PWM_LOWEST_MIN > 0
else if (pwm->values[i] < PWM_LOWEST_MIN) {
_failsafe_pwm[i] = PWM_LOWEST_MIN;
}
#endif
else {
_failsafe_pwm[i] = pwm->values[i];
}
}
/*
* update the counter
* this is needed to decide if disarmed PWM output should be turned on or not
*/
_num_failsafe_set = 0;
for (unsigned i = 0; i < _max_actuators; i++) {
if (_failsafe_pwm[i] > 0) {
_num_failsafe_set++;
}
}
break;
}
case PWM_SERVO_GET_FAILSAFE_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
for (unsigned i = 0; i < _max_actuators; i++) {
pwm->values[i] = _failsafe_pwm[i];
}
pwm->channel_count = _max_actuators;
break;
}
case PWM_SERVO_SET_DISARMED_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
/* discard if too many values are sent */
if (pwm->channel_count > _max_actuators) {
ret = -EINVAL;
break;
}
for (unsigned i = 0; i < pwm->channel_count; i++) {
if (pwm->values[i] == 0) {
/* ignore 0 */
} else if (pwm->values[i] > PWM_HIGHEST_MAX) {
_disarmed_pwm[i] = PWM_HIGHEST_MAX;
}
#if PWM_LOWEST_MIN > 0
else if (pwm->values[i] < PWM_LOWEST_MIN) {
_disarmed_pwm[i] = PWM_LOWEST_MIN;
}
#endif
else {
_disarmed_pwm[i] = pwm->values[i];
}
}
/*
* update the counter
* this is needed to decide if disarmed PWM output should be turned on or not
*/
_num_disarmed_set = 0;
for (unsigned i = 0; i < _max_actuators; i++) {
if (_disarmed_pwm[i] > 0) {
_num_disarmed_set++;
}
}
break;
}
case PWM_SERVO_GET_DISARMED_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
for (unsigned i = 0; i < _max_actuators; i++) {
pwm->values[i] = _disarmed_pwm[i];
}
pwm->channel_count = _max_actuators;
break;
}
case PWM_SERVO_SET_MIN_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
/* discard if too many values are sent */
if (pwm->channel_count > _max_actuators) {
ret = -EINVAL;
break;
}
for (unsigned i = 0; i < pwm->channel_count; i++) {
if (pwm->values[i] == 0) {
/* ignore 0 */
} else if (pwm->values[i] > PWM_HIGHEST_MIN) {
_min_pwm[i] = PWM_HIGHEST_MIN;
}
#if PWM_LOWEST_MIN > 0
else if (pwm->values[i] < PWM_LOWEST_MIN) {
_min_pwm[i] = PWM_LOWEST_MIN;
}
#endif
else {
_min_pwm[i] = pwm->values[i];
}
}
break;
}
case PWM_SERVO_GET_MIN_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
for (unsigned i = 0; i < _max_actuators; i++) {
pwm->values[i] = _min_pwm[i];
}
pwm->channel_count = _max_actuators;
arg = (unsigned long)&pwm;
break;
}
case PWM_SERVO_SET_MAX_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
/* discard if too many values are sent */
if (pwm->channel_count > _max_actuators) {
ret = -EINVAL;
break;
}
for (unsigned i = 0; i < pwm->channel_count; i++) {
if (pwm->values[i] == 0) {
/* ignore 0 */
} else if (pwm->values[i] < PWM_LOWEST_MAX) {
_max_pwm[i] = PWM_LOWEST_MAX;
} else if (pwm->values[i] > PWM_HIGHEST_MAX) {
_max_pwm[i] = PWM_HIGHEST_MAX;
} else {
_max_pwm[i] = pwm->values[i];
}
}
break;
}
case PWM_SERVO_GET_MAX_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
for (unsigned i = 0; i < _max_actuators; i++) {
pwm->values[i] = _max_pwm[i];
}
pwm->channel_count = _max_actuators;
arg = (unsigned long)&pwm;
break;
}
case PWM_SERVO_SET_TRIM_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
/* discard if too many values are sent */
if (pwm->channel_count > _max_actuators) {
PX4_DEBUG("error: too many trim values: %d", pwm->channel_count);
ret = -EINVAL;
break;
}
/* copy the trim values to the mixer offsets */
_mixers->set_trims((int16_t *)pwm->values, pwm->channel_count);
PX4_DEBUG("set_trims: %d, %d, %d, %d", pwm->values[0], pwm->values[1], pwm->values[2], pwm->values[3]);
break;
}
case PWM_SERVO_GET_TRIM_PWM: {
struct pwm_output_values *pwm = (struct pwm_output_values *)arg;
pwm->channel_count = _mixers->get_trims((int16_t *)pwm->values);
break;
}
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 14
case PWM_SERVO_SET(13):
case PWM_SERVO_SET(12):
case PWM_SERVO_SET(11):
case PWM_SERVO_SET(10):
case PWM_SERVO_SET(9):
case PWM_SERVO_SET(8):
if (_mode < MODE_14PWM) {
ret = -EINVAL;
break;
}
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
case PWM_SERVO_SET(7):
/* FALLTHROUGH */
case PWM_SERVO_SET(6):
if (_mode < MODE_8PWM) {
ret = -EINVAL;
break;
}
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
/* FALLTHROUGH */
case PWM_SERVO_SET(5):
/* FALLTHROUGH */
case PWM_SERVO_SET(4):
if (_mode < MODE_6PWM) {
ret = -EINVAL;
break;
}
#endif
/* FALLTHROUGH */
case PWM_SERVO_SET(3):
if (_mode < MODE_4PWM) {
ret = -EINVAL;
break;
}
/* FALLTHROUGH */
case PWM_SERVO_SET(2):
if (_mode < MODE_3PWM) {
ret = -EINVAL;
break;
}
/* FALLTHROUGH */
case PWM_SERVO_SET(1):
case PWM_SERVO_SET(0):
if (arg <= 2100) {
up_pwm_servo_set(cmd - PWM_SERVO_SET(0), arg);
} else {
ret = -EINVAL;
}
break;
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 14
case PWM_SERVO_GET(13):
case PWM_SERVO_GET(12):
case PWM_SERVO_GET(11):
case PWM_SERVO_GET(10):
case PWM_SERVO_GET(9):
case PWM_SERVO_GET(8):
if (_mode < MODE_14PWM) {
ret = -EINVAL;
break;
}
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
/* FALLTHROUGH */
case PWM_SERVO_GET(7):
case PWM_SERVO_GET(6):
if (_mode < MODE_8PWM) {
ret = -EINVAL;
break;
}
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
/* FALLTHROUGH */
case PWM_SERVO_GET(5):
case PWM_SERVO_GET(4):
if (_mode < MODE_6PWM) {
ret = -EINVAL;
break;
}
#endif
/* FALLTHROUGH */
case PWM_SERVO_GET(3):
if (_mode < MODE_4PWM) {
ret = -EINVAL;
break;
}
/* FALLTHROUGH */
case PWM_SERVO_GET(2):
if (_mode < MODE_3PWM) {
ret = -EINVAL;
break;
}
/* FALLTHROUGH */
case PWM_SERVO_GET(1):
case PWM_SERVO_GET(0):
*(servo_position_t *)arg = up_pwm_servo_get(cmd - PWM_SERVO_GET(0));
break;
case PWM_SERVO_GET_RATEGROUP(0):
case PWM_SERVO_GET_RATEGROUP(1):
case PWM_SERVO_GET_RATEGROUP(2):
case PWM_SERVO_GET_RATEGROUP(3):
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
case PWM_SERVO_GET_RATEGROUP(4):
case PWM_SERVO_GET_RATEGROUP(5):
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
case PWM_SERVO_GET_RATEGROUP(6):
case PWM_SERVO_GET_RATEGROUP(7):
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 14
case PWM_SERVO_GET_RATEGROUP(8):
case PWM_SERVO_GET_RATEGROUP(9):
case PWM_SERVO_GET_RATEGROUP(10):
case PWM_SERVO_GET_RATEGROUP(11):
case PWM_SERVO_GET_RATEGROUP(12):
case PWM_SERVO_GET_RATEGROUP(13):
#endif
*(uint32_t *)arg = up_pwm_servo_get_rate_group(cmd - PWM_SERVO_GET_RATEGROUP(0));
break;
case PWM_SERVO_GET_COUNT:
case MIXERIOCGETOUTPUTCOUNT:
switch (_mode) {
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 14
case MODE_14PWM:
*(unsigned *)arg = 14;
break;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
case MODE_8PWM:
*(unsigned *)arg = 8;
break;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
case MODE_6PWM:
*(unsigned *)arg = 6;
break;
#endif
case MODE_4PWM:
*(unsigned *)arg = 4;
break;
case MODE_3PWM:
case MODE_3PWM1CAP:
*(unsigned *)arg = 3;
break;
case MODE_2PWM:
case MODE_2PWM2CAP:
*(unsigned *)arg = 2;
break;
case MODE_1PWM:
*(unsigned *)arg = 1;
break;
default:
ret = -EINVAL;
break;
}
break;
case PWM_SERVO_SET_COUNT: {
/* change the number of outputs that are enabled for
* PWM. This is used to change the split between GPIO
* and PWM under control of the flight config
* parameters.
*/
switch (arg) {
case 0:
set_mode(MODE_NONE);
break;
case 1:
set_mode(MODE_1PWM);
break;
case 2:
set_mode(MODE_2PWM);
break;
case 3:
set_mode(MODE_3PWM);
break;
case 4:
set_mode(MODE_4PWM);
break;
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >=6
case 6:
set_mode(MODE_6PWM);
break;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >=8
case 8:
set_mode(MODE_8PWM);
break;
#endif
default:
ret = -EINVAL;
break;
}
break;
}
case PWM_SERVO_SET_MODE: {
switch (arg) {
case PWM_SERVO_MODE_NONE:
ret = set_mode(MODE_NONE);
break;
case PWM_SERVO_MODE_1PWM:
ret = set_mode(MODE_1PWM);
break;
case PWM_SERVO_MODE_2PWM:
ret = set_mode(MODE_2PWM);
break;
case PWM_SERVO_MODE_2PWM2CAP:
ret = set_mode(MODE_2PWM2CAP);
break;
case PWM_SERVO_MODE_3PWM:
ret = set_mode(MODE_3PWM);
break;
case PWM_SERVO_MODE_3PWM1CAP:
ret = set_mode(MODE_3PWM1CAP);
break;
case PWM_SERVO_MODE_4PWM:
ret = set_mode(MODE_4PWM);
break;
case PWM_SERVO_MODE_6PWM:
ret = set_mode(MODE_6PWM);
break;
case PWM_SERVO_MODE_8PWM:
ret = set_mode(MODE_8PWM);
break;
case PWM_SERVO_MODE_4CAP:
ret = set_mode(MODE_4CAP);
break;
case PWM_SERVO_MODE_5CAP:
ret = set_mode(MODE_5CAP);
break;
case PWM_SERVO_MODE_6CAP:
ret = set_mode(MODE_6CAP);
break;
default:
ret = -EINVAL;
}
break;
}
#ifdef SPEKTRUM_POWER
case DSM_BIND_START:
/* only allow DSM2, DSM-X and DSM-X with more than 7 channels */
PX4_INFO("DSM_BIND_START: DSM%s RX", (arg == 0) ? "2" : ((arg == 1) ? "-X" : "-X8"));
if (arg == DSM2_BIND_PULSES ||
arg == DSMX_BIND_PULSES ||
arg == DSMX8_BIND_PULSES) {
dsm_bind(DSM_CMD_BIND_POWER_DOWN, 0);
dsm_bind(DSM_CMD_BIND_SET_RX_OUT, 0);
usleep(500000);
dsm_bind(DSM_CMD_BIND_POWER_UP, 0);
usleep(72000);
irqstate_t flags = px4_enter_critical_section();
dsm_bind(DSM_CMD_BIND_SEND_PULSES, arg);
px4_leave_critical_section(flags);
usleep(50000);
dsm_bind(DSM_CMD_BIND_REINIT_UART, 0);
ret = OK;
} else {
PX4_ERR("DSM bind failed");
ret = -EINVAL;
}
break;
#endif
case MIXERIOCRESET:
if (_mixers != nullptr) {
delete _mixers;
_mixers = nullptr;
_groups_required = 0;
}
break;
case MIXERIOCADDSIMPLE: {
mixer_simple_s *mixinfo = (mixer_simple_s *)arg;
SimpleMixer *mixer = new SimpleMixer(control_callback, (uintptr_t)_controls, mixinfo);
if (mixer->check()) {
delete mixer;
_groups_required = 0;
ret = -EINVAL;
} else {
if (_mixers == nullptr) {
_mixers = new MixerGroup(control_callback, (uintptr_t)_controls);
}
_mixers->add_mixer(mixer);
_mixers->groups_required(_groups_required);
}
break;
}
case MIXERIOCLOADBUF: {
const char *buf = (const char *)arg;
unsigned buflen = strnlen(buf, 1024);
if (_mixers == nullptr) {
_mixers = new MixerGroup(control_callback, (uintptr_t)_controls);
}
if (_mixers == nullptr) {
_groups_required = 0;
ret = -ENOMEM;
} else {
ret = _mixers->load_from_buf(buf, buflen);
if (ret != 0) {
PX4_DEBUG("mixer load failed with %d", ret);
delete _mixers;
_mixers = nullptr;
_groups_required = 0;
ret = -EINVAL;
} else {
_mixers->groups_required(_groups_required);
PX4_DEBUG("loaded mixers \n%s\n", buf);
update_pwm_trims();
}
}
break;
}
default:
ret = -ENOTTY;
break;
}
unlock();
return ret;
}
/*
this implements PWM output via a write() method, for compatibility
with px4io
*/
ssize_t
PX4FMU::write(file *filp, const char *buffer, size_t len)
{
unsigned count = len / 2;
uint16_t values[MAX_ACTUATORS];
#if BOARD_HAS_PWM == 0
return 0;
#endif
if (count > BOARD_HAS_PWM) {
// we have at most BOARD_HAS_PWM outputs
count = BOARD_HAS_PWM;
}
if (count > MAX_ACTUATORS) {
count = MAX_ACTUATORS;
}
// allow for misaligned values
memcpy(values, buffer, count * 2);
for (unsigned i = count; i < _num_outputs; ++i) {
values[i] = PWM_IGNORE_THIS_CHANNEL;
}
reorder_outputs(values);
for (unsigned i = 0; i < _num_outputs; i++) {
if (values[i] != PWM_IGNORE_THIS_CHANNEL) {
up_pwm_servo_set(i, values[i]);
}
}
return count * 2;
}
void
PX4FMU::reorder_outputs(uint16_t values[MAX_ACTUATORS])
{
if (MAX_ACTUATORS < 4) {
return;
}
if (_motor_ordering == MotorOrdering::Betaflight) {
/*
* Betaflight default motor ordering:
* 4 2
* ^
* 3 1
*/
const uint16_t pwm_tmp[4] = {values[0], values[1], values[2], values[3] };
values[0] = pwm_tmp[3];
values[1] = pwm_tmp[0];
values[2] = pwm_tmp[1];
values[3] = pwm_tmp[2];
}
/* else: PX4, no need to reorder
* 3 1
* ^
* 2 4
*/
}
void
PX4FMU::sensor_reset(int ms)
{
if (ms < 1) {
ms = 1;
}
board_spi_reset(ms);
}
void
PX4FMU::peripheral_reset(int ms)
{
if (ms < 1) {
ms = 10;
}
board_peripheral_reset(ms);
}
int
PX4FMU::gpio_reset(void)
{
#if !defined(BOARD_HAS_FMU_GPIO)
return -EINVAL;
#else
/*
* Setup default GPIO config - all pins as GPIOs, input if
* possible otherwise output if possible.
*/
for (unsigned i = 0; i < _ngpio; i++) {
if (_gpio_tab[i].input != 0) {
px4_arch_configgpio(_gpio_tab[i].input);
} else if (_gpio_tab[i].output != 0) {
px4_arch_configgpio(_gpio_tab[i].output);
}
}
# if defined(GPIO_GPIO_DIR)
/* if we have a GPIO direction control, set it to zero (input) */
px4_arch_gpiowrite(GPIO_GPIO_DIR, 0);
px4_arch_configgpio(GPIO_GPIO_DIR);
# endif
return OK;
#endif // !defined(BOARD_HAS_FMU_GPIO)
}
int
PX4FMU::gpio_set_function(uint32_t gpios, int function)
{
#if !defined(BOARD_HAS_FMU_GPIO)
return -EINVAL;
#else
/* configure selected GPIOs as required */
for (unsigned i = 0; i < _ngpio; i++) {
if (gpios & (1 << i)) {
switch (function) {
case GPIO_SET_OUTPUT:
if (_gpio_tab[i].output) {
px4_arch_configgpio(_gpio_tab[i].output);
}
break;
}
}
}
return OK;
#endif // !defined(BOARD_HAS_FMU_GPIO)
}
int
PX4FMU::gpio_write(uint32_t gpios, int function)
{
#if !defined(BOARD_HAS_FMU_GPIO)
return -EINVAL;
#else
int value = (function == GPIO_SET) ? 1 : 0;
for (unsigned i = 0; i < _ngpio; i++) {
if (gpios & (1 << i)) {
if (_gpio_tab[i].output) {
px4_arch_gpiowrite(_gpio_tab[i].output, value);
}
}
}
return OK;
#endif
}
int
PX4FMU::gpio_read(uint32_t *value)
{
#if !defined(BOARD_HAS_FMU_GPIO)
return -EINVAL;
#else
uint32_t bits = 0;
for (unsigned i = 0; i < _ngpio; i++) {
if (_gpio_tab[i].input != 0 && px4_arch_gpioread(_gpio_tab[i].input)) {
bits |= (1 << i);
}
}
*value = bits;
return OK;
#endif
}
int
PX4FMU::capture_ioctl(struct file *filp, int cmd, unsigned long arg)
{
int ret = -EINVAL;
#if defined(BOARD_HAS_CAPTURE)
lock();
input_capture_config_t *pconfig = 0;
input_capture_stats_t *stats = (input_capture_stats_t *)arg;
if (_mode == MODE_3PWM1CAP || _mode == MODE_2PWM2CAP) {
pconfig = (input_capture_config_t *)arg;
}
switch (cmd) {
case INPUT_CAP_SET:
if (pconfig) {
ret = up_input_capture_set(pconfig->channel, pconfig->edge, pconfig->filter,
pconfig->callback, pconfig->context);
}
break;
case INPUT_CAP_SET_CALLBACK:
if (pconfig) {
ret = up_input_capture_set_callback(pconfig->channel, pconfig->callback, pconfig->context);
}
break;
case INPUT_CAP_GET_CALLBACK:
if (pconfig) {
ret = up_input_capture_get_callback(pconfig->channel, &pconfig->callback, &pconfig->context);
}
break;
case INPUT_CAP_GET_STATS:
if (arg) {
ret = up_input_capture_get_stats(stats->chan_in_edges_out, stats, false);
}
break;
case INPUT_CAP_GET_CLR_STATS:
if (arg) {
ret = up_input_capture_get_stats(stats->chan_in_edges_out, stats, true);
}
break;
case INPUT_CAP_SET_EDGE:
if (pconfig) {
ret = up_input_capture_set_trigger(pconfig->channel, pconfig->edge);
}
break;
case INPUT_CAP_GET_EDGE:
if (pconfig) {
ret = up_input_capture_get_trigger(pconfig->channel, &pconfig->edge);
}
break;
case INPUT_CAP_SET_FILTER:
if (pconfig) {
ret = up_input_capture_set_filter(pconfig->channel, pconfig->filter);
}
break;
case INPUT_CAP_GET_FILTER:
if (pconfig) {
ret = up_input_capture_get_filter(pconfig->channel, &pconfig->filter);
}
break;
case INPUT_CAP_GET_COUNT:
ret = OK;
switch (_mode) {
case MODE_3PWM1CAP:
*(unsigned *)arg = 1;
break;
case MODE_2PWM2CAP:
*(unsigned *)arg = 2;
break;
default:
ret = -EINVAL;
break;
}
break;
case INPUT_CAP_SET_COUNT:
ret = OK;
switch (_mode) {
case MODE_3PWM1CAP:
set_mode(MODE_3PWM1CAP);
break;
case MODE_2PWM2CAP:
set_mode(MODE_2PWM2CAP);
break;
default:
ret = -EINVAL;
break;
}
break;
default:
ret = -ENOTTY;
break;
}
unlock();
#else
ret = -ENOTTY;
#endif
return ret;
}
int
PX4FMU::gpio_ioctl(struct file *filp, int cmd, unsigned long arg)
{
int ret = OK;
lock();
switch (cmd) {
case GPIO_RESET:
ret = gpio_reset();
break;
case GPIO_SET_OUTPUT:
ret = gpio_set_function(arg, cmd);
break;
case GPIO_SET:
case GPIO_CLEAR:
ret = gpio_write(arg, cmd);
break;
default:
ret = -ENOTTY;
}
unlock();
return ret;
}
int
PX4FMU::fmu_new_mode(PortMode new_mode)
{
if (!is_running()) {
return -1;
}
PX4FMU::Mode servo_mode;
bool mode_with_input = false;
servo_mode = PX4FMU::MODE_NONE;
switch (new_mode) {
case PORT_FULL_GPIO:
case PORT_MODE_UNSET:
break;
case PORT_FULL_PWM:
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM == 4
/* select 4-pin PWM mode */
servo_mode = PX4FMU::MODE_4PWM;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM == 6
servo_mode = PX4FMU::MODE_6PWM;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM == 8
servo_mode = PX4FMU::MODE_8PWM;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM == 14
servo_mode = PX4FMU::MODE_14PWM;
#endif
break;
case PORT_RC_IN:
servo_mode = PX4FMU::MODE_NONE;
break;
case PORT_PWM1:
/* select 2-pin PWM mode */
servo_mode = PX4FMU::MODE_1PWM;
break;
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
case PORT_PWM6:
/* select 4-pin PWM mode */
servo_mode = PX4FMU::MODE_6PWM;
break;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
case PORT_PWM4:
/* select 4-pin PWM mode */
servo_mode = PX4FMU::MODE_4PWM;
break;
case PORT_PWM3:
/* select 3-pin PWM mode */
servo_mode = PX4FMU::MODE_3PWM;
break;
case PORT_PWM3CAP1:
/* select 3-pin PWM mode 1 capture */
servo_mode = PX4FMU::MODE_3PWM1CAP;
mode_with_input = true;
break;
case PORT_PWM2:
/* select 2-pin PWM mode */
servo_mode = PX4FMU::MODE_2PWM;
break;
case PORT_PWM2CAP2:
/* select 2-pin PWM mode 2 capture */
servo_mode = PX4FMU::MODE_2PWM2CAP;
mode_with_input = true;
break;
#endif
default:
return -1;
}
PX4FMU *object = get_instance();
if (servo_mode != object->get_mode()) {
/* reset to all-inputs */
if (mode_with_input) {
object->ioctl(0, GPIO_RESET, 0);
}
/* (re)set the PWM output mode */
object->set_mode(servo_mode);
}
return OK;
}
namespace
{
void
bind_spektrum()
{
int fd = open(PX4FMU_DEVICE_PATH, O_RDWR);
if (fd < 0) {
PX4_ERR("open fail");
return;
}
/* specify 11ms DSMX. RX will automatically fall back to 22ms or DSM2 if necessary */
ioctl(fd, DSM_BIND_START, DSMX8_BIND_PULSES);
close(fd);
}
int fmu_new_i2c_speed(unsigned bus, unsigned clock_hz)
{
return PX4FMU::set_i2c_bus_clock(bus, clock_hz);
}
} // namespace
int
PX4FMU::test()
{
int fd;
unsigned servo_count = 0;
unsigned capture_count = 0;
unsigned pwm_value = 1000;
int direction = 1;
int ret;
uint32_t rate_limit = 0;
struct input_capture_t {
bool valid;
input_capture_config_t chan;
} capture_conf[INPUT_CAPTURE_MAX_CHANNELS];
fd = ::open(PX4FMU_DEVICE_PATH, O_RDWR);
if (fd < 0) {
PX4_ERR("open fail");
return -1;
}
if (::ioctl(fd, PWM_SERVO_ARM, 0) < 0) {
PX4_ERR("servo arm failed");
goto err_out;
}
if (::ioctl(fd, PWM_SERVO_GET_COUNT, (unsigned long)&servo_count) != 0) {
PX4_ERR("Unable to get servo count");
goto err_out;
}
if (::ioctl(fd, INPUT_CAP_GET_COUNT, (unsigned long)&capture_count) != 0) {
PX4_INFO("Not in a capture mode");
}
PX4_INFO("Testing %u servos and %u input captures", (unsigned)servo_count, capture_count);
memset(capture_conf, 0, sizeof(capture_conf));
if (capture_count != 0) {
for (unsigned i = 0; i < capture_count; i++) {
// Map to channel number
capture_conf[i].chan.channel = i + servo_count;
/* Save handler */
if (::ioctl(fd, INPUT_CAP_GET_CALLBACK, (unsigned long)&capture_conf[i].chan.channel) != 0) {
PX4_ERR("Unable to get capture callback for chan %u\n", capture_conf[i].chan.channel);
goto err_out;
} else {
input_capture_config_t conf = capture_conf[i].chan;
conf.callback = &PX4FMU::capture_trampoline;
conf.context = PX4FMU::get_instance();
if (::ioctl(fd, INPUT_CAP_SET_CALLBACK, (unsigned long)&conf) == 0) {
capture_conf[i].valid = true;
} else {
PX4_ERR("Unable to set capture callback for chan %u\n", capture_conf[i].chan.channel);
goto err_out;
}
}
}
}
struct pollfd fds;
fds.fd = 0; /* stdin */
fds.events = POLLIN;
PX4_INFO("Press CTRL-C or 'c' to abort.");
for (;;) {
/* sweep all servos between 1000..2000 */
servo_position_t servos[servo_count];
for (unsigned i = 0; i < servo_count; i++) {
servos[i] = pwm_value;
}
if (direction == 1) {
// use ioctl interface for one direction
for (unsigned i = 0; i < servo_count; i++) {
if (::ioctl(fd, PWM_SERVO_SET(i), servos[i]) < 0) {
PX4_ERR("servo %u set failed", i);
goto err_out;
}
}
} else {
// and use write interface for the other direction
ret = ::write(fd, servos, sizeof(servos));
if (ret != (int)sizeof(servos)) {
PX4_ERR("error writing PWM servo data, wrote %u got %d", sizeof(servos), ret);
goto err_out;
}
}
if (direction > 0) {
if (pwm_value < 2000) {
pwm_value++;
} else {
direction = -1;
}
} else {
if (pwm_value > 1000) {
pwm_value--;
} else {
direction = 1;
}
}
/* readback servo values */
for (unsigned i = 0; i < servo_count; i++) {
servo_position_t value;
if (::ioctl(fd, PWM_SERVO_GET(i), (unsigned long)&value)) {
PX4_ERR("error reading PWM servo %d", i);
goto err_out;
}
if (value != servos[i]) {
PX4_ERR("servo %d readback error, got %u expected %u", i, value, servos[i]);
goto err_out;
}
}
if (capture_count != 0 && (++rate_limit % 500 == 0)) {
for (unsigned i = 0; i < capture_count; i++) {
if (capture_conf[i].valid) {
input_capture_stats_t stats;
stats.chan_in_edges_out = capture_conf[i].chan.channel;
if (::ioctl(fd, INPUT_CAP_GET_STATS, (unsigned long)&stats) != 0) {
PX4_ERR("Unable to get stats for chan %u\n", capture_conf[i].chan.channel);
goto err_out;
} else {
fprintf(stdout, "FMU: Status chan:%u edges: %d last time:%lld last state:%d overflows:%d lantency:%u\n",
capture_conf[i].chan.channel,
stats.chan_in_edges_out,
stats.last_time,
stats.last_edge,
stats.overflows,
stats.latnecy);
}
}
}
}
/* Check if user wants to quit */
char c;
ret = ::poll(&fds, 1, 0);
if (ret > 0) {
::read(0, &c, 1);
if (c == 0x03 || c == 0x63 || c == 'q') {
PX4_INFO("User abort");
break;
}
}
}
if (capture_count != 0) {
for (unsigned i = 0; i < capture_count; i++) {
// Map to channel number
if (capture_conf[i].valid) {
/* Save handler */
if (::ioctl(fd, INPUT_CAP_SET_CALLBACK, (unsigned long)&capture_conf[i].chan) != 0) {
PX4_ERR("Unable to set capture callback for chan %u\n", capture_conf[i].chan.channel);
goto err_out;
}
}
}
}
::close(fd);
return 0;
err_out:
::close(fd);
return -1;
}
int
PX4FMU::fake(int argc, char *argv[])
{
if (argc < 5) {
print_usage("not enough arguments");
return -1;
}
actuator_controls_s ac;
ac.control[0] = strtol(argv[1], 0, 0) / 100.0f;
ac.control[1] = strtol(argv[2], 0, 0) / 100.0f;
ac.control[2] = strtol(argv[3], 0, 0) / 100.0f;
ac.control[3] = strtol(argv[4], 0, 0) / 100.0f;
orb_advert_t handle = orb_advertise(ORB_ID_VEHICLE_ATTITUDE_CONTROLS, &ac);
if (handle == nullptr) {
PX4_ERR("advertise failed");
return -1;
}
orb_unadvertise(handle);
actuator_armed_s aa;
aa.armed = true;
aa.lockdown = false;
handle = orb_advertise(ORB_ID(actuator_armed), &aa);
if (handle == nullptr) {
PX4_ERR("advertise failed 2");
return -1;
}
orb_unadvertise(handle);
return 0;
}
PX4FMU *PX4FMU::instantiate(int argc, char *argv[])
{
// No arguments to parse. We also know that we should run as task
return new PX4FMU(true);
}
int PX4FMU::custom_command(int argc, char *argv[])
{
PortMode new_mode = PORT_MODE_UNSET;
const char *verb = argv[0];
if (!strcmp(verb, "bind")) {
bind_spektrum();
return 0;
}
/* does not operate on a FMU instance */
if (!strcmp(verb, "i2c")) {
if (argc > 2) {
int bus = strtol(argv[1], 0, 0);
int clock_hz = strtol(argv[2], 0, 0);
int ret = fmu_new_i2c_speed(bus, clock_hz);
if (ret) {
PX4_ERR("setting I2C clock failed");
}
return ret;
}
return print_usage("not enough arguments");
}
if (!strcmp(verb, "sensor_reset")) {
if (argc > 1) {
int reset_time = strtol(argv[1], nullptr, 0);
sensor_reset(reset_time);
} else {
sensor_reset(0);
PX4_INFO("reset default time");
}
return 0;
}
if (!strcmp(verb, "peripheral_reset")) {
if (argc > 2) {
int reset_time = strtol(argv[2], 0, 0);
peripheral_reset(reset_time);
} else {
peripheral_reset(0);
PX4_INFO("reset default time");
}
return 0;
}
/* start the FMU if not running */
if (!is_running()) {
int ret = PX4FMU::task_spawn(argc, argv);
if (ret) {
return ret;
}
}
/*
* Mode switches.
*/
if (!strcmp(verb, "mode_gpio")) {
new_mode = PORT_FULL_GPIO;
} else if (!strcmp(verb, "mode_rcin")) {
new_mode = PORT_RC_IN;
} else if (!strcmp(verb, "mode_pwm")) {
new_mode = PORT_FULL_PWM;
// mode: defines which outputs to drive (others may be used by other tasks such as camera capture)
#if defined(BOARD_HAS_PWM)
} else if (!strcmp(verb, "mode_pwm1")) {
new_mode = PORT_PWM1;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
} else if (!strcmp(verb, "mode_pwm4")) {
new_mode = PORT_PWM4;
} else if (!strcmp(verb, "mode_pwm2")) {
new_mode = PORT_PWM2;
} else if (!strcmp(verb, "mode_pwm3")) {
new_mode = PORT_PWM3;
} else if (!strcmp(verb, "mode_pwm3cap1")) {
new_mode = PORT_PWM3CAP1;
} else if (!strcmp(verb, "mode_pwm2cap2")) {
new_mode = PORT_PWM2CAP2;
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
} else if (!strcmp(verb, "mode_pwm6")) {
new_mode = PORT_PWM6;
#endif
}
/* was a new mode set? */
if (new_mode != PORT_MODE_UNSET) {
/* switch modes */
return PX4FMU::fmu_new_mode(new_mode);
}
if (!strcmp(verb, "test")) {
return test();
}
if (!strcmp(verb, "fake")) {
return fake(argc - 1, argv + 1);
}
return print_usage("unknown command");
}
int PX4FMU::print_usage(const char *reason)
{
if (reason) {
PX4_WARN("%s\n", reason);
}
PRINT_MODULE_DESCRIPTION(
R"DESCR_STR(
### Description
This module is responsible for driving the output and reading the input pins. For boards without a separate IO chip
(eg. Pixracer), it uses the main channels. On boards with an IO chip (eg. Pixhawk), it uses the AUX channels, and the
px4io driver is used for main ones.
It listens on the actuator_controls topics, does the mixing and writes the PWM outputs.
In addition it does the RC input parsing and auto-selecting the method. Supported methods are:
- PPM
- SBUS
- DSM
- SUMD
- ST24
The module is configured via mode_* commands. This defines which of the first N pins the driver should occupy.
By using mode_pwm4 for example, pins 5 and 6 can be used by the camera trigger driver or by a PWM rangefinder
driver. Alternatively, the fmu can be started in one of the capture modes, and then drivers can register a capture
callback with ioctl calls.
### Implementation
By default the module runs on the work queue, to reduce RAM usage. It can also be run in its own thread,
specified via start flag -t, to reduce latency.
When running on the work queue, it schedules at a fixed frequency, and the pwm rate limits the update rate of
the actuator_controls topics. In case of running in its own thread, the module polls on the actuator_controls topic.
Additionally the pwm rate defines the lower-level IO timer rates.
### Examples
It is typically started with:
$ fmu mode_pwm
To drive all available pins.
Capture input (rising and falling edges) and print on the console: start the fmu in one of the capture modes:
$ fmu mode_pwm3cap1
This will enable capturing on the 4th pin. Then do:
$ fmu test
Use the `pwm` command for further configurations (PWM rate, levels, ...), and the `mixer` command to load
mixer files.
)DESCR_STR");
PRINT_MODULE_USAGE_NAME("fmu", "driver");
PRINT_MODULE_USAGE_COMMAND_DESCR("start", "Start the task (without any mode set, use any of the mode_* cmds)");
PRINT_MODULE_USAGE_PARAM_FLAG('t', "Run as separate task instead of the work queue", true);
PRINT_MODULE_USAGE_PARAM_COMMENT("All of the mode_* commands will start the fmu if not running already");
PRINT_MODULE_USAGE_COMMAND("mode_gpio");
PRINT_MODULE_USAGE_COMMAND_DESCR("mode_rcin", "Only do RC input, no PWM outputs");
PRINT_MODULE_USAGE_COMMAND_DESCR("mode_pwm", "Select all available pins as PWM");
#if defined(BOARD_HAS_PWM)
PRINT_MODULE_USAGE_COMMAND("mode_pwm1");
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 6
PRINT_MODULE_USAGE_COMMAND("mode_pwm4");
PRINT_MODULE_USAGE_COMMAND("mode_pwm2");
PRINT_MODULE_USAGE_COMMAND("mode_pwm3");
PRINT_MODULE_USAGE_COMMAND("mode_pwm3cap1");
PRINT_MODULE_USAGE_COMMAND("mode_pwm2cap2");
#endif
#if defined(BOARD_HAS_PWM) && BOARD_HAS_PWM >= 8
PRINT_MODULE_USAGE_COMMAND("mode_pwm6");
#endif
PRINT_MODULE_USAGE_COMMAND_DESCR("bind", "Send a DSM bind command (module must be running)");
PRINT_MODULE_USAGE_COMMAND_DESCR("sensor_reset", "Do a sensor reset (SPI bus)");
PRINT_MODULE_USAGE_ARG("<ms>", "Delay time in ms between reset and re-enabling", true);
PRINT_MODULE_USAGE_COMMAND_DESCR("peripheral_reset", "Reset board peripherals");
PRINT_MODULE_USAGE_ARG("<ms>", "Delay time in ms between reset and re-enabling", true);
PRINT_MODULE_USAGE_COMMAND_DESCR("i2c", "Configure I2C clock rate");
PRINT_MODULE_USAGE_ARG("<bus_id> <rate>", "Specify the bus id (>=0) and rate in Hz", false);
PRINT_MODULE_USAGE_COMMAND_DESCR("test", "Test inputs and outputs");
PRINT_MODULE_USAGE_COMMAND_DESCR("fake", "Arm and send an actuator controls command");
PRINT_MODULE_USAGE_ARG("<roll> <pitch> <yaw> <thrust>", "Control values in range [-100, 100]", false);
PRINT_MODULE_USAGE_DEFAULT_COMMANDS();
return 0;
}
int PX4FMU::print_status()
{
PX4_INFO("Running %s", (_run_as_task ? "as task" : "on work queue"));
if (!_run_as_task) {
PX4_INFO("Max update rate: %i Hz", _current_update_rate);
}
PX4_INFO("RC scan state: %s", RC_SCAN_STRING[_rc_scan_state]);
#ifdef RC_SERIAL_PORT
PX4_INFO("SBUS frame drops: %u", sbus_dropped_frames());
#endif
const char *mode_str = nullptr;
switch (_mode) {
case MODE_1PWM: mode_str = "pwm1"; break;
case MODE_2PWM: mode_str = "pwm2"; break;
case MODE_3PWM: mode_str = "pwm3"; break;
case MODE_4PWM: mode_str = "pwm4"; break;
case MODE_2PWM2CAP: mode_str = "pwm2cap2"; break;
case MODE_3PWM1CAP: mode_str = "pwm3cap1"; break;
case MODE_6PWM: mode_str = "pwm6"; break;
case MODE_8PWM: mode_str = "pwm8"; break;
case MODE_4CAP: mode_str = "cap4"; break;
case MODE_5CAP: mode_str = "cap5"; break;
case MODE_6CAP: mode_str = "cap6"; break;
case MODE_NONE: mode_str = "no pwm"; break;
default:
break;
}
if (mode_str) {
PX4_INFO("PWM Mode: %s", mode_str);
}
return 0;
}
extern "C" __EXPORT int fmu_main(int argc, char *argv[]);
int
fmu_main(int argc, char *argv[])
{
return PX4FMU::main(argc, argv);
}
Reference in New Issue View Git Blame Copy Permalink