# 모듈 참조: 명령

## bl_update

Source: [systemcmds/actuator_test](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/actuator_test)

파일에서 부트로더를 플래시하는 유틸리티

WARNING: remove all props before using this command.

<a id="actuator_test_usage"></a>

### 사용법

```
actuator_test <command> [arguments...]
 Commands:
   set           Set an actuator to a specific output value

 The actuator can be specified by motor, servo or function directly:
     [-m <val>]  Motor to test (1...8)
     [-s <val>]  Servo to test (1...8)
     [-f <val>]  Specify function directly
     -v <val>    value (-1...1)
     [-t <val>]  Timeout in seconds (run interactive if not set)
                 default: 0

   iterate-motors Iterate all motors starting and stopping one after the other

   iterate-servos Iterate all servos deflecting one after the other
```

## dumpfile

Source: [systemcmds/bl_update](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/bl_update)

Utility to flash the bootloader from a file <a id="bl_update_usage"></a>

### 사용법

```
bl_update [arguments...]
   setopt        Set option bits to unlock the FLASH (only needed if in locked
                 state)

   <file>        Bootloader bin file
```

## bsondump

Source: [systemcmds/bsondump](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/bsondump)

Utility to read BSON from a file and print or output document size. <a id="bsondump_usage"></a>

### 사용법

```
bsondump [arguments...]
     <file>      The BSON file to decode and print.
```

## dyn

Source: [systemcmds/dumpfile](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/dumpfile)

Dump file utility. Prints file size and contents in binary mode (don't replace LF with CR LF) to stdout. <a id="dumpfile_usage"></a>

### 사용법

```
dumpfile [arguments...]
     <file>      File to dump
```

## esc_calib

Source: [systemcmds/dyn](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/dyn)

### 설명

소스: <a href="https://github.com/PX4/PX4-Autopilot/tree/master/src/systemcmds/failure">systemcmds/failure</a>

### 예

```
dyn ./hello.px4mod start
```

<a id="dyn_usage"></a>

### 사용법

```
dyn [arguments...]
     <file>      File containing the module
     [arguments...] Arguments to the module
```

## failure

Source: [systemcmds/failure](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/failure)

### 설명

Inject failures into system.

### 구현

This system command sends a vehicle command over uORB to trigger failure.

### 예

Test the GPS failsafe by stopping GPS:

failure gps off

<a id="failure_usage"></a>

### 사용법

```
failure [arguments...]
   help          Show this help text

   gps|...       Specify component

   ok|off|...    Specify failure type
     [-i <val>]  sensor instance (0=all)
                 default: 0
```

## gpio

Source: [systemcmds/gpio](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/gpio)

### 설명

This command is used to read and write GPIOs

```
gpio read <PORT><PIN>/<DEVICE> [PULLDOWN|PULLUP] [--force]
gpio write <PORT><PIN>/<DEVICE> <VALUE> [PUSHPULL|OPENDRAIN] [--force]
```

### 예

Read the value on port H pin 4 configured as pullup, and it is high

```
gpio read H4 PULLUP
```

1 OK

Set the output value on Port E pin 7 to high

```
gpio write E7 1 --force
```

Set the output value on device /dev/gpio1 to high

```
gpio write /dev/gpio1 1
```

<a id="gpio_usage"></a>

### 사용법

```
gpio [arguments...]
   read
     <PORT><PIN>/<DEVICE> GPIO port and pin or device
     [PULLDOWN|PULLUP] Pulldown/Pullup
     [--force]   Force (ignore board gpio list)

   write
     <PORT> <PIN> GPIO port and pin
     <VALUE>     Value to write
     [PUSHPULL|OPENDRAIN] Pushpull/Opendrain
     [--force]   Force (ignore board gpio list)
```

## hardfault_log

Source: [systemcmds/hardfault_log](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/hardfault_log)

Hardfault utility

Used in startup scripts to handle hardfaults

<a id="hardfault_log_usage"></a>

### 사용법

```
hardfault_log <command> [arguments...]
 Commands:
   check         Check if there's an uncommitted hardfault

   rearm         Drop an uncommitted hardfault

   fault         Generate a hardfault (this command crashes the system :)
     [0|1|2|3]   Hardfault type: 0=divide by 0, 1=Assertion, 2=jump to 0x0,
                 3=write to 0x0 (default=0)

   commit        Write uncommitted hardfault to /fs/microsd/fault_%i.txt (and
                 rearm, but don't reset)

   count         Read the reboot counter, counts the number of reboots of an
                 uncommitted hardfault (returned as the exit code of the
                 program)

   reset         Reset the reboot counter
```

## hist

Source: [systemcmds/hist](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/hist)

Command-line tool to show the px4 message history. There are no arguments. <a id="hist_usage"></a>

### 사용법

```
hist [arguments...]
```

## i2cdetect

Source: [systemcmds/i2cdetect](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/i2cdetect)

Utility to scan for I2C devices on a particular bus. <a id="i2cdetect_usage"></a>

### 사용법

```
i2cdetect [arguments...]
     [-b <val>]  I2C bus
                 default: 1
```

## led_control

Source: [systemcmds/led_control](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/led_control)

### 설명

Command-line tool to control & test the (external) LED's.

To use it make sure there's a driver running, which handles the led_control uorb topic.

There are different priorities, such that for example one module can set a color with low priority, and another
module can blink N times with high priority, and the LED's automatically return to the lower priority state
after the blinking. The `reset` command can also be used to return to a lower priority.

### 예

Blink the first LED 5 times in blue:

```
led_control blink -c blue -l 0 -n 5
```

<a id="led_control_usage"></a>

### 사용법

```
led_control <command> [arguments...]
 Commands:
   test          Run a test pattern

   on            Turn LED on

   off           Turn LED off

   reset         Reset LED priority

   blink         Blink LED N times
     [-n <val>]  Number of blinks
                 default: 3
     [-s <val>]  Set blinking speed
                 values: fast|normal|slow, default: normal

   breathe       Continuously fade LED in & out

   flash         Two fast blinks and then off with frequency of 1Hz

 The following arguments apply to all of the above commands except for 'test':
     [-c <val>]  color
                 values: red|blue|green|yellow|purple|amber|cyan|white, default:
                 white
     [-l <val>]  Which LED to control: 0, 1, 2, ... (default=all)
     [-p <val>]  Priority
                 default: 2
```

## listener

Source: [systemcmds/topic_listener](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/topic_listener)

Utility to listen on uORB topics and print the data to the console.

The listener can be exited any time by pressing Ctrl+C, Esc, or Q.

<a id="listener_usage"></a>

### 사용법

```
listener <command> [arguments...]
 Commands:
     <topic_name> uORB topic name
     [-i <val>]  Topic instance
                 default: 0
     [-n <val>]  Number of messages
                 default: 1
     [-r <val>]  Subscription rate (unlimited if 0)
                 default: 0
```

## mfd

Source: [systemcmds/mft](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/mft)

Utility interact with the manifest <a id="mfd_usage"></a>

### 사용법

```
mfd <command> [arguments...]
 Commands:
   query         Returns true if not existed
```

## mft_cfg

Source: [systemcmds/mft_cfg](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/mft_cfg)

Tool to set and get manifest configuration <a id="mft_cfg_usage"></a>

### 사용법

```
mft_cfg <command> [arguments...]
 Commands:
   get           get manifest configuration

   set           set manifest configuration

   reset         reset manifest configuration
     hwver|hwrev Select type: MTD_MTF_VER|MTD_MTF_REV
     -i <val>    argument to set extended hardware id (id == version for
                 <hwver>, id == revision for <hwrev> )
```

## mtd

Source: [systemcmds/mtd](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/mtd)

Utility to mount and test partitions (based on FRAM/EEPROM storage as defined by the board) <a id="mtd_usage"></a>

### 사용법

```
mtd <command> [arguments...]
 Commands:
   status        Print status information

   readtest      Perform read test

   rwtest        Perform read-write test

   erase         Erase partition(s)

 The commands 'readtest' and 'rwtest' have an optional instance index:
     [-i <val>]  storage index (if the board has multiple storages)
                 default: 0

 The commands 'readtest', 'rwtest' and 'erase' have an optional parameter:
     [<partition_name1> [<partition_name2> ...]] Partition names (eg.
                 /fs/mtd_params), use system default if not provided
```

## nshterm

Source: [systemcmds/nshterm](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/nshterm)

Start an NSH shell on a given port.

This was previously used to start a shell on the USB serial port.
Now there runs mavlink, and it is possible to use a shell over mavlink.

<a id="nshterm_usage"></a>

### 사용법

```
nshterm [arguments...]
     <file:dev>  Device on which to start the shell (eg. /dev/ttyACM0)
```

## param

Source: [systemcmds/param](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/param)

### 설명

Command to access and manipulate parameters via shell or script.

This is used for example in the startup script to set airframe-specific parameters.

Parameters are automatically saved when changed, eg. with `param set`. They are typically stored to FRAM
or to the SD card. `param select` can be used to change the storage location for subsequent saves (this will
need to be (re-)configured on every boot).

If the FLASH-based backend is enabled (which is done at compile time, e.g. for the Intel Aero or Omnibus),
`param select` has no effect and the default is always the FLASH backend. However `param save/load <file>`
can still be used to write to/read from files.

Each parameter has a 'used' flag, which is set when it's read during boot. It is used to only show relevant
parameters to a ground control station.

### 예

Change the airframe and make sure the airframe's default parameters are loaded:

```
param set SYS_AUTOSTART 4001
param set SYS_AUTOCONFIG 1
reboot
```

<a id="param_usage"></a>

### 사용법

```
param <command> [arguments...]
 Commands:
   load          Load params from a file (overwrite all)
     [<file>]    File name (use default if not given)

   import        Import params from a file
     [<file>]    File name (use default if not given)

   save          Save params to a file
     [<file>]    File name (use default if not given)

   select        Select default file
     [<file>]    File name

   select-backup Select default file
     [<file>]    File name

   show          Show parameter values
     [-a]        Show all parameters (not just used)
     [-c]        Show only changed params (unused too)
     [-q]        quiet mode, print only param value (name needs to be exact)
     [<filter>]  Filter by param name (wildcard at end allowed, eg. sys_*)

   show-for-airframe Show changed params for airframe config

   status        Print status of parameter system

   set           Set parameter to a value
     <param_name> <value> Parameter name and value to set
     [fail]      If provided, let the command fail if param is not found

   set-default   Set parameter default to a value
     [-s]        If provided, silent errors if parameter doesn't exists
     <param_name> <value> Parameter name and value to set
     [fail]      If provided, let the command fail if param is not found

   compare       Compare a param with a value. Command will succeed if equal
     [-s]        If provided, silent errors if parameter doesn't exists
     <param_name> <value> Parameter name and value to compare

   greater       Compare a param with a value. Command will succeed if param is
                 greater than the value
     [-s]        If provided, silent errors if parameter doesn't exists
     <param_name> <value> Parameter name and value to compare
     <param_name> <value> Parameter name and value to compare

   touch         Mark a parameter as used
     [<param_name1> [<param_name2>]] Parameter name (one or more)

   reset         Reset only specified params to default
     [<param1> [<param2>]] Parameter names to reset (wildcard at end allowed)

   reset_all     Reset all params to default
     [<exclude1> [<exclude2>]] Do not reset matching params (wildcard at end
                 allowed)

   index         Show param for a given index
     <index>     Index: an integer >= 0

   index_used    Show used param for a given index
     <index>     Index: an integer >= 0

   find          Show index of a param
     <param>     param name
```

## payload_deliverer

Source: [modules/payload_deliverer](https://github.com/PX4/PX4-Autopilot/tree/main/src/modules/payload_deliverer)

### 설명

Handles payload delivery with either Gripper or a Winch with an appropriate timeout / feedback sensor setting,
and communicates back the delivery result as an acknowledgement internally

<a id="payload_deliverer_usage"></a>

### 사용법

```
payload_deliverer <command> [arguments...]
 Commands:
   start

   gripper_test  Tests the Gripper's release & grabbing sequence

   gripper_open  Opens the gripper

   gripper_close Closes the gripper

   stop

   status        print status info
```

## perf

Source: [systemcmds/perf](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/perf)

Tool to print performance counters <a id="perf_usage"></a>

### 사용법

```
perf [arguments...]
   reset         Reset all counters

   latency       Print HRT timer latency histogram

 Prints all performance counters if no arguments given
```

## reboot

Source: [systemcmds/reboot](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/reboot)

Reboot the system <a id="reboot_usage"></a>

### 사용법

```
reboot [arguments...]
     [-b]        Reboot into bootloader
     [-i]        Reboot into ISP (1st stage bootloader)
     [lock|unlock] Take/release the shutdown lock (for testing)
```

## sd_bench

Source: [systemcmds/sd_bench](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/sd_bench)

Test the speed of an SD Card <a id="sd_bench_usage"></a>

### 사용법

```
sd_bench [arguments...]
     [-b <val>]  Block size for each read/write
                 default: 4096
     [-r <val>]  Number of runs
                 default: 5
     [-d <val>]  Duration of a run in ms
                 default: 2000
     [-k]        Keep the test file
     [-s]        Call fsync after each block (default=at end of each run)
     [-u]        Test performance with unaligned data
     [-U]        Test performance with forced byte unaligned data
     [-v]        Verify data and block number
```

## sd_stress

Source: [systemcmds/sd_stress](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/sd_stress)

Test operations on an SD Card <a id="sd_stress_usage"></a>

### 사용법

```
sd_stress [arguments...]
     [-r <val>]  Number of runs
                 default: 5
     [-b <val>]  Number of bytes
                 default: 100
```

## serial_passthru

Source: [systemcmds/serial_passthru](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/serial_passthru)

Pass data from one device to another.

This can be used to use u-center connected to USB with a GPS on a serial port.

<a id="serial_passthru_usage"></a>

### 사용법

```
serial_passthru [arguments...]
     -e <val>    External device path
                 values: <file:dev>
     -d <val>    Internal device path
                 values: <file:dev>
     [-b <val>]  Baudrate
                 default: 115200
     [-t]        Track the External devices baudrate on internal device
```

## system_time

Source: [systemcmds/system_time](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/system_time)

### 설명

Command-line tool to set and get system time.

### 예

Set the system time and read it back

```
system_time set 1600775044
system_time get
```

<a id="system_time_usage"></a>

### 사용법

```
system_time <command> [arguments...]
 Commands:
   set           Set the system time, provide time in unix epoch time format

   get           Get the system time
```

## top

Source: [systemcmds/top](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/top)

Monitor running processes and their CPU, stack usage, priority and state <a id="top_usage"></a>

### 사용법

```
top [arguments...]
   once          print load only once
```

## usb_connected

Source: [systemcmds/usb_connected](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/usb_connected)

Utility to check if USB is connected. Was previously used in startup scripts.
A return value of 0 means USB is connected, 1 otherwise. <a id="usb_connected_usage"></a>

### 사용법

```
usb_connected [arguments...]
```

## ver

Source: [systemcmds/ver](https://github.com/PX4/PX4-Autopilot/tree/main/src/systemcmds/ver)

Tool to print various version information <a id="ver_usage"></a>

### 사용법

```
ver <command> [arguments...]
 Commands:
   hw            Hardware architecture

   mcu           MCU info

   git           git version information

   bdate         Build date and time

   gcc           Compiler info

   bdate         Build date and time

   px4guid       PX4 GUID

   uri           Build URI

   all           Print all versions

   hwcmp         Compare hardware version (returns 0 on match)
     <hw> [<hw2>] Hardware to compare against (eg. PX4_FMU_V4). An OR comparison
                 is used if multiple are specified

   hwtypecmp     Compare hardware type (returns 0 on match)
     <hwtype> [<hwtype2>] Hardware type to compare against (eg. V2). An OR
                 comparison is used if multiple are specified

   hwbasecmp     Compare hardware base (returns 0 on match)
     <hwbase> [<hwbase2>] Hardware type to compare against (eg. V2). An OR
                 comparison is used if multiple are specified
```