# Offboard 模式 飞行器根据飞行控制栈外部（如机载计算机）提供的设定值控制位置、速度、加速度、姿态以及推力/力矩。 The setpoints may be provided using MAVLink (or a MAVLink API such as [MAVSDK](https://mavsdk.mavlink.io/)) or by [ROS 2](../ros2/index.md). PX4 requires that the external controller provides a continuous 2Hz "proof of life" signal, by streaming any of the supported MAVLink setpoint messages or the ROS 2 [OffboardControlMode](../msg_docs/OffboardControlMode.md) message. PX4只有在收到该种信号超过1秒后才有效，如果该种信号停止飞行控制栈将重新获得控制权（脱离Offboard模式）。 ::: info - 此模式需要位置或位/姿信息 - 例如 GPS、光流、视觉惯性里程计、mocap 等。 - RC control is disabled except to change modes (you can also fly without any manual controller at all by setting the parameter [COM_RC_IN_MODE](../advanced_config/parameter_reference.md#COM_RC_IN_MODE) to 4: Stick input disabled). - The vehicle must be already be receiving a stream of MAVLink setpoint messages or ROS 2 [OffboardControlMode](../msg_docs/OffboardControlMode.md) messages before arming in offboard mode or switching to offboard mode when flying. - The vehicle will exit offboard mode if MAVLink setpoint messages or `OffboardControlMode` are not received at a rate of > 2Hz. - 并非所有 MAVLink 支持的坐标系和字段值都被设定值消息和飞行器支持。 Read the sections below _carefully_ to ensure only supported values are used. ::: ## 描述 Offboard模式通过设置位置、速度、加速、姿态、姿态角速率或力/扭矩设定值来控制飞行器的位置和姿态。 PX4 must receive a stream of MAVLink setpoint messages or the ROS 2 [OffboardControlMode](../msg_docs/OffboardControlMode.md) at 2 Hz as proof that the external controller is healthy. 该消息必须持续发送1秒以上PX4才能在Offboard模式下解锁或在飞行中切换至Offboard模式。 If the rate falls below 2Hz while under external control PX4 will switch out of offboard mode after a timeout ([COM_OF_LOSS_T](#COM_OF_LOSS_T)), and attempt to land or perform some other failsafe action. The action depends on whether or not RC control is available, and is defined in the parameter [COM_OBL_RC_ACT](#COM_OBL_RC_ACT). 当使用 MAVLink 时，设定值消息既传达了外部控制器"正常运行"的信号也传达了设定值本身。 Offboard模式下要保持位置，飞行器必须接收到一个包含当前位置设定值的消息指令。 When using ROS 2 the proof that the external source is alive is provided by a stream of [OffboardControlMode](../msg_docs/OffboardControlMode.md) messages, while the actual setpoint is provided by publishing to one of the setpoint uORB topics, such as [TrajectorySetpoint](../msg_docs/TrajectorySetpoint.md). In order to hold position in this case the vehicle must receive a stream of `OffboardControlMode` but would only need the `TrajectorySetpoint` once. 请注意，Offboard模式只支持比较有限的 MAVLink 指令和消息。 其他操作如起飞、降落、返航，最好使用适当的模式来处理。 像上传、下载任务这样的操作可以在任何模式下执行。 ## ROS 2 消息 以下 ROS 2 消息及其特定字段和字段值在特定的框架下是允许的。 In addition to providing heartbeat functionality, `OffboardControlMode` has two other main purposes: 1. Controls the level of the [PX4 control architecture](../flight_stack/controller_diagrams.md) at which offboard setpoints must be injected, and disables the bypassed controllers. 2. 确定需要哪种有效估计(位置或速度)，以及应该使用哪种设定值消息。 The `OffboardControlMode` message is defined as shown. ```sh # Off-board control mode uint64 timestamp # time since system start (microseconds) bool position bool velocity bool acceleration bool attitude bool body_rate bool thrust_and_torque bool direct_actuator ``` The fields are ordered in terms of priority such that `position` takes precedence over `velocity` and later fields, `velocity` takes precedence over `acceleration`, and so on. 第一个非零字段(从上到下) 定义了Offboard模式所需的有效估计以及可用的设定值消息。 For example, if the `acceleration` field is the first non-zero value, then PX4 requires a valid `velocity estimate`, and the setpoint must be specified using the `TrajectorySetpoint` message. | 期望控制对象 | 位置 | 速度 | 加速度 | 姿态 | 姿态角速率 | 执行器字段 | 直接给电机 | 所需状态估计 | 所需消息 | | ------------------------------ | --------------------------- | --------------------------- | --------------------------- | --------------------------- | --------------------------- | --------------------------- | --------------------------- | ------ | ------------------------------------------------------------------------------------------------------------------------------- | | 位置 (NED) | ✓ | - | - | - | - | - | - | 位置 | [TrajectorySetpoint](../msg_docs/TrajectorySetpoint.md) | | 速度 (NED) | ✗ | ✓ | - | - | - | - | - | 速度 | [TrajectorySetpoint](../msg_docs/TrajectorySetpoint.md) | | 加速度（NED） | ✗ | ✗ | ✓ | - | - | - | - | 速度 | [TrajectorySetpoint](../msg_docs/TrajectorySetpoint.md) | | 姿态(FRD) | ✗ | ✗ | ✗ | ✓ | - | - | - | 无 | [VehicleAttitudeSetpoint](../msg_docs/VehicleAttitudeSetpoint.md) | | 体轴角速率 (FRD) | ✗ | ✗ | ✗ | ✗ | ✓ | - | - | 无 | [VehicleRatesSetpoint](../msg_docs/VehicleRatesSetpoint.md) | | 推力和力矩(FRD) | ✗ | ✗ | ✗ | ✗ | ✗ | ✓ | - | 无 | [VehicleThrustSetpoint](../msg_docs/VehicleThrustSetpoint.md) and [VehicleTorqueSetpoint](../msg_docs/VehicleTorqueSetpoint.md) | | 直接给电机和舵机 | ✗ | ✗ | ✗ | ✗ | ✗ | ✗ | ✓ | 无 | [ActuatorMotors](../msg_docs/ActuatorMotors.md) and [ActuatorServos](../msg_docs/ActuatorServos.md) | where ✓ means that the bit is set, ✘ means that the bit is not set and `-` means that the bit is value is irrelevant. :::info Before using offboard mode with ROS 2, please spend a few minutes understanding the different [frame conventions](../ros2/user_guide.md#ros-2-px4-frame-conventions) that PX4 and ROS 2 use. ::: ### 旋翼机 - [px4_msgs::msg::TrajectorySetpoint](https://github.com/PX4/PX4-Autopilot/blob/main/msg/TrajectorySetpoint.msg) - 支持以下输入组合： - Position setpoint (`position` different from `NaN`). Non-`NaN` values of velocity and acceleration are used as feedforward terms for the inner loop controllers. - Velocity setpoint (`velocity` different from `NaN` and `position` set to `NaN`). Non-`NaN` values acceleration are used as feedforward terms for the inner loop controllers. - Acceleration setpoint (`acceleration` different from `NaN` and `position` and `velocity` set to `NaN`) - 所有值都是基于NED(北, 东, 地)坐标系，位置、速度和加速的单位分别为\[m\], \[m/s\] 和\[m/s^2\] 。 - [px4_msgs::msg::VehicleAttitudeSetpoint](https://github.com/PX4/PX4-Autopilot/blob/main/msg/VehicleAttitudeSetpoint.msg) - 支持以下输入组合： - quaternion `q_d` + thrust setpoint `thrust_body`. Non-`NaN` values of `yaw_sp_move_rate` are used as feedforward terms expressed in Earth frame and in \[rad/s\]. - 姿态四元数表示无人机机体坐标系FRD(前、右、下) 与NED坐标系之间的旋转。 这个推力是在无人机体轴FRD坐标系下，并归一化为 \[-1, 1\] 。 - [px4_msgs::msg::VehicleRatesSetpoint](https://github.com/PX4/PX4-Autopilot/blob/main/msg/VehicleRatesSetpoint.msg) - 支持以下输入组合： - `roll`, `pitch`, `yaw` and `thrust_body`. - 所有值都表示在无人机体轴FRD坐标系下。 角速率(roll, pitch, yaw) 单位为\[rad/s\] ，thrust_body归一化为 \[-1, 1\]。 ### Generic Vehicle 下面的offboard控制模式会绕过所有PX4内部的控制环，应当非常谨慎地使用。 - [px4_msgs::msg::VehicleThrustSetpoint](https://github.com/PX4/PX4-Autopilot/blob/main/msg/VehicleThrustSetpoint.msg) + [px4_msgs::msg::VehicleTorqueSetpoint](https://github.com/PX4/PX4-Autopilot/blob/main/msg/VehicleTorqueSetpoint.msg) - 支持以下输入组合： - `xyz` for thrust and `xyz` for torque. - 所有值都在无人机体轴 FRD 坐标系中表示，并且归一化为\[-1, 1\]。 - [px4_msgs::msg::ActuatorMotors](https://github.com/PX4/PX4-Autopilot/blob/main/msg/ActuatorMotors.msg) + [px4_msgs::msg::ActuatorServos](https://github.com/PX4/PX4-Autopilot/blob/main/msg/ActuatorServos.msg) - 直接控制电机输出和/或伺服系统（舵机）输出。 - Currently works at lower level than then `control_allocator` module. Do not publish these messages when not in offboard mode. - 所有值归一化为\[-1, 1\]。 For outputs that do not support negative values, negative entries map to `NaN`. - `NaN` maps to disarmed. ## MAVLink 消息 下面的 MAVLink 消息及其特定字段和字段值在特定的帧下是允许的。 ### 直升机/垂直起降 - [SET_POSITION_TARGET_LOCAL_NED](https://mavlink.io/en/messages/common.html#SET_POSITION_TARGET_LOCAL_NED) - The following input combinations are supported: - Position setpoint (only `x`, `y`, `z`) - Velocity setpoint (only `vx`, `vy`, `vz`) - Acceleration setpoint (only `afx`, `afy`, `afz`) - Position setpoint **and** velocity setpoint (the velocity setpoint is used as feedforward; it is added to the output of the position controller and the result is used as the input to the velocity controller). - Position setpoint **and** velocity setpoint **and** acceleration (the velocity and the acceleration setpoints are used as feedforwards; the velocity setpoint is added to the output of the position controller and the result is used as the input to the velocity controller; the acceleration setpoint is added to the output of the velocity controller and the result used to compute the thrust vector). - PX4 supports the following `coordinate_frame` values (only): [MAV_FRAME_LOCAL_NED](https://mavlink.io/en/messages/common.html#MAV_FRAME_LOCAL_NED) and [MAV_FRAME_BODY_NED](https://mavlink.io/en/messages/common.html#MAV_FRAME_BODY_NED). - [SET_POSITION_TARGET_GLOBAL_INT](https://mavlink.io/en/messages/common.html#SET_POSITION_TARGET_GLOBAL_INT) - The following input combinations are supported: - Position setpoint (only `lat_int`, `lon_int`, `alt`) - Velocity setpoint (only `vx`, `vy`, `vz`) - _Thrust_ setpoint (only `afx`, `afy`, `afz`) ::: info Acceleration setpoint values are mapped to create a normalized thrust setpoint (i.e. acceleration setpoints are not "properly" supported). ::: - Position setpoint **and** velocity setpoint (the velocity setpoint is used as feedforward; it is added to the output of the position controller and the result is used as the input to the velocity controller). - PX4 supports the following `coordinate_frame` values (only): [MAV_FRAME_GLOBAL](https://mavlink.io/en/messages/common.html#MAV_FRAME_GLOBAL). - [SET_ATTITUDE_TARGET](https://mavlink.io/en/messages/common.html#SET_ATTITUDE_TARGET) - 支持以下输入组合： - Attitude/orientation (`SET_ATTITUDE_TARGET.q`) with thrust setpoint (`SET_ATTITUDE_TARGET.thrust`). - Body rate (`SET_ATTITUDE_TARGET` `.body_roll_rate` ,`.body_pitch_rate`, `.body_yaw_rate`) with thrust setpoint (`SET_ATTITUDE_TARGET.thrust`). ### Fixed-wing - [SET_POSITION_TARGET_LOCAL_NED](https://mavlink.io/en/messages/common.html#SET_POSITION_TARGET_LOCAL_NED) - The following input combinations are supported (via `type_mask`): - Position setpoint (`x`, `y`, `z` only; velocity and acceleration setpoints are ignored). - Specify the _type_ of the setpoint in `type_mask` (if these bits are not set the vehicle will fly in a flower-like pattern): ::: info Some of the _setpoint type_ values below are not part of the MAVLink standard for the `type_mask` field. ::: 值为： - 292：滑动设定值。 这会将 TECS 配置为空速优先于高度，以便在没有推力时使无人机滑行（即控制俯仰以调节空速）。 It is equivalent to setting `type_mask` as `POSITION_TARGET_TYPEMASK_Z_IGNORE`, `POSITION_TARGET_TYPEMASK_VZ_IGNORE`, `POSITION_TARGET_TYPEMASK_AZ_IGNORE`. - 4096：起飞设定值。 - 8192：降落设定值。 - 12288：悬停设定值（以设定值为中心绕圈飞行）。 - 16384：空闲设定值（油门为0， 横滚 / 俯仰为0）。 - PX4 supports the coordinate frames (`coordinate_frame` field): [MAV_FRAME_LOCAL_NED](https://mavlink.io/en/messages/common.html#MAV_FRAME_LOCAL_NED) and [MAV_FRAME_BODY_NED](https://mavlink.io/en/messages/common.html#MAV_FRAME_BODY_NED). - [SET_POSITION_TARGET_GLOBAL_INT](https://mavlink.io/en/messages/common.html#SET_POSITION_TARGET_GLOBAL_INT) - The following input combinations are supported (via `type_mask`): - Position setpoint (only `lat_int`, `lon_int`, `alt`) - Specify the _type_ of the setpoint in `type_mask` (if these bits are not set the vehicle will fly in a flower-like pattern): ::: info The _setpoint type_ values below are not part of the MAVLink standard for the `type_mask` field. ::: 值为： - 4096：起飞设定值。 - 8192：降落设定值。 - 12288：悬停设定值（以设定值为中心绕圈飞行）。 - 16384：空闲设定值（油门为0， 横滚 / 俯仰为0）。 - PX4 supports the following `coordinate_frame` values (only): [MAV_FRAME_GLOBAL](https://mavlink.io/en/messages/common.html#MAV_FRAME_GLOBAL). - [SET_ATTITUDE_TARGET](https://mavlink.io/en/messages/common.html#SET_ATTITUDE_TARGET) - 支持以下输入组合： - Attitude/orientation (`SET_ATTITUDE_TARGET.q`) with thrust setpoint (`SET_ATTITUDE_TARGET.thrust`). - Body rate (`SET_ATTITUDE_TARGET` `.body_roll_rate` ,`.body_pitch_rate`, `.body_yaw_rate`) with thrust setpoint (`SET_ATTITUDE_TARGET.thrust`). ### 无人车 - [SET_POSITION_TARGET_LOCAL_NED](https://mavlink.io/en/messages/common.html#SET_POSITION_TARGET_LOCAL_NED) - The following input combinations are supported (in `type_mask`): - Position setpoint (only `x`, `y`, `z`) - Specify the _type_ of the setpoint in `type_mask`: ::: info The _setpoint type_ values below are not part of the MAVLink standard for the `type_mask` field. :: 值为： - 12288：悬停设定值（无人机足够接近设定值时会停止）。 - Velocity setpoint (only `vx`, `vy`, `vz`) - PX4 supports the coordinate frames (`coordinate_frame` field): [MAV_FRAME_LOCAL_NED](https://mavlink.io/en/messages/common.html#MAV_FRAME_LOCAL_NED) and [MAV_FRAME_BODY_NED](https://mavlink.io/en/messages/common.html#MAV_FRAME_BODY_NED). - [SET_POSITION_TARGET_GLOBAL_INT](https://mavlink.io/en/messages/common.html#SET_POSITION_TARGET_GLOBAL_INT) - The following input combinations are supported (in `type_mask`): - Position setpoint (only `lat_int`, `lon_int`, `alt`) - Specify the _type_ of the setpoint in `type_mask` (not part of the MAVLink standard). 值为： - 下面的比特位没有置位，是正常表现。 - 12288：悬停设定值（无人机足够接近设定值时会停止）。 - PX4 supports the coordinate frames (`coordinate_frame` field): [MAV_FRAME_GLOBAL](https://mavlink.io/en/messages/common.html#MAV_FRAME_GLOBAL). - [SET_ATTITUDE_TARGET](https://mavlink.io/en/messages/common.html#SET_ATTITUDE_TARGET) - 支持以下输入组合： - Attitude/orientation (`SET_ATTITUDE_TARGET.q`) with thrust setpoint (`SET_ATTITUDE_TARGET.thrust`). ::: info Only the yaw setting is actually used/extracted. ::: ## Offboard参数 _Offboard mode_ is affected by the following parameters: | 参数 | 描述 | | ----------------------------------------------------------------------------------------------------------------------------------------------------------------------- | --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- | | [COM_OF_LOSS_T](../advanced_config/parameter_reference.md#COM_OF_LOSS_T) | Time-out (in seconds) to wait when offboard connection is lost before triggering offboard lost failsafe (`COM_OBL_RC_ACT`) | | [COM_OBL_RC_ACT](../advanced_config/parameter_reference.md#COM_OBL_RC_ACT) | Flight mode to switch to if offboard control is lost (Values are - `0`: _Position_, `1`: _Altitude_, `2`: _Manual_, `3`: \*Return, `4`: \*Land\*). | | [COM_RC_OVERRIDE](../advanced_config/parameter_reference.md#COM_RC_OVERRIDE) | Controls whether stick movement on a multicopter (or VTOL in MC mode) causes a mode change to [Position mode](../flight_modes_mc/position.md). 默认情况下未启用此功能。 | | [COM_RC_STICK_OV](../advanced_config/parameter_reference.md#COM_RC_STICK_OV) | The amount of stick movement that causes a transition to [Position mode](../flight_modes_mc/position.md) (if [COM_RC_OVERRIDE](#COM_RC_OVERRIDE) is enabled). | | [COM_RCL_EXCEPT](../advanced_config/parameter_reference.md#COM_RCL_EXCEPT) | 该参数指定一种模式，在该模式下将忽略RC丢失及不会触发RC丢失的失效保护动作。 Set bit `2` to ignore RC loss in Offboard mode. | ## 开发者资源 Typically developers do not directly work at the MAVLink layer, but instead use a robotics API like [MAVSDK](https://mavsdk.mavlink.io/) or [ROS](http://www.ros.org/) (these provide a developer friendly API, and take care of managing and maintaining connections, sending messages and monitoring responses - the minutiae of working with _Offboard mode_ and MAVLink). 以下资源可能对开发者有用： - [Offboard Control from Linux](../ros/offboard_control.md) - [ROS/MAVROS Offboard Example (C++)](../ros/mavros_offboard_cpp.md) - [ROS/MAVROS Offboard Example (Python)](../ros/mavros_offboard_python.md)