# Barometers

Barometers measure atmospheric pressure, and are used in drones as altitude sensors.

Most [flight controllers](../flight_controller/index.md) on which PX4 runs include a barometer.
By default PX4 will select the barometer with the highest priority (if any are present), and configure it as a data source for [Height estimation](../advanced_config/tuning_the_ecl_ekf.md#height).
If a sensor fault is detected, PX4 will fall back to the next highest priority sensor.

Generally barometers require no user configuration (or thought)!

## 하드웨어 옵션

[Pixhawk standard](../flight_controller/autopilot_pixhawk_standard.md) flight controllers include a barometer, as do [many others](../flight_controller/index.md).

They are also present in other hardware:

- [CUAV NEO 3 Pro GNSS module](https://doc.cuav.net/gps/neo-series-gnss/en/neo-3-pro.html#key-data) ([MS5611](../modules/modules_driver_baro.md#ms5611))
- [RaccoonLab L1 GNSS NEO-M8N](https://raccoonlab.co/tproduct/360882105-258620719271-cyphal-and-dronecan-gnss-m8n-magnetomete)

At time of writing, drivers/parts include: bmp280, bmp388 (and BMP380), dps310, goertek (spl06), invensense (icp10100, icp10111, icp101xx, icp201xx), lps22hb, lps25h, lps33hw, maiertek (mpc2520), mpl3115a2, ms5611, ms5837, tcbp001ta.

Note that the supported barometer part numbers can be inferred from the driver names listed in the [Modules Reference: Baro (Driver)](../modules/modules_driver_baro.md) documentation (and the driver source: [PX4-Autopilot/src/drivers/barometer](https://github.com/PX4/PX4-Autopilot/tree/main/src/drivers/barometer)).

## PX4 설정

Generally barometers require no user configuration.
If needed, you can:

- Enable/Disable barometers as data source for [Height estimation](../advanced_config/tuning_the_ecl_ekf.md#height) using the [EKF2_BARO_CTRL](../advanced_config/parameter_reference.md#EKF2_BARO_CTRL) parameter.
- Change the selection order of barometers using the [CAL_BAROx_PRIO](../advanced_config/parameter_reference.md#CAL_BARO0_PRIO) parameters for each barometer.
- Disable a barometer by setting its [CAL_BAROx_PRIO](../advanced_config/parameter_reference.md#CAL_BARO0_PRIO) value to `0`.

## Calibration

Barometers don't require calibration.

<!-- Notes:
- Absolute value isn't important since we just use the difference in altitude between "now" and the value when initializing EKF2
- There is usually a scale factor error but it's compensated by the GNSS altitude using a bias estimator in EKF2 (we don't provide a way to calibrate that). This method is fine as long as the height change of the drone isn't too fast (below 200-300km/h probably; don't have real data on that).
- The baro readings can be corrected using a param SENS_BARO_QNH (https://en.wikipedia.org/wiki/Altimeter_setting) parameter, but again, it is only necessary to adjust it if the absolute barometric altitude is required by the pilot.
-->

## 개발자 정보

- [Baro driver source code](https://github.com/PX4/PX4-Autopilot/tree/main/src/drivers/barometer)
- [Modules Reference: Baro (Driver)](../modules/modules_driver_baro.md) documentation.