# Pixhawk 4 接线快速入门 :::warning PX4 does not manufacture this (or any) autopilot. Contact the [manufacturer](https://holybro.com/) for hardware support or compliance issues. ::: This quick start guide shows how to power the [Pixhawk 4](../flight_controller/pixhawk4.md)® flight controller and connect its most important peripherals. ## 接线图概述 下图展示了如何连接最重要的传感器和外围设备（电机和伺服舵机输出除外）。 我们将在下面各节中介绍它们的细节。 ![Pixhawk 4 Wiring Overview](../../assets/flight_controller/pixhawk4/pixhawk4_wiring_overview.png) :::tip More information about available ports can be found here: [Pixhawk 4 > Connections](../flight_controller/pixhawk4.md#connectors). ::: ## 飞控的安装和方向 _Pixhawk 4_ should be mounted on the frame using vibration-damping foam pads (included in the kit). It should be positioned as close to your vehicle’s center of gravity as possible, oriented top-side up with the arrow pointing towards the front of the vehicle. :::info If the controller cannot be mounted in the recommended/default orientation (e.g. due to space constraints) you will need to configure the autopilot software with the orientation that you actually used: [Flight Controller Orientation](../config/flight_controller_orientation.md). ::: ## GPS + 指南针 + 蜂鸣器 + 安全开关 + LED Attach the provided GPS with integrated compass, safety switch, buzzer and LED to the **GPS MODULE** port. The GPS/Compass should be [mounted on the frame](../assembly/mount_gps_compass.md) as far away from other electronics as possible, with the direction marker towards the front of the vehicle (separating the compass from other electronics will reduce interference). ![Connect compass/GPS to Pixhawk 4](../../assets/flight_controller/pixhawk4/pixhawk4_compass_gps.jpg) :::info The GPS module's integrated safety switch is enabled _by default_ (when enabled, PX4 will not let you arm the vehicle). To disable the safety press and hold the safety switch for 1 second. You can press the safety switch again to enable safety and disarm the vehicle (this can be useful if, for whatever reason, you are unable to disarm the vehicle from your remote control or ground station). ::: ## 电源 Connect the output of the _Power Management Board_ (PM board) that comes with the kit to one of the **POWER** bricks of _Pixhawk 4_ using a 6-wire cable. The PM input **2~12S** will be connected to your LiPo battery. The connections of Power Management Board, including power supply and signal connections to the ESCs and servos, are explained in the table below. Note that the PM board does not supply power to the servos via + and - pins of **FMU PWM-OUT**. The image below shows the power management board provided with _Pixhawk 4_. ![Pixhawk 4 - Power Management Board](../../assets/hardware/power_module/holybro_pm07/pixhawk4_power_management_board.png) :::info If using a plane or rover, the 8 pin power (+) rail of **FMU PWM-OUT** will need to be separately powered in order to drive servos for rudders, elevons etc. To do this, the power rail needs to be connected to a BEC equipped ESC or a standalone 5V BEC or a 2S LiPo battery. Be careful with the voltage of servo you are going to use here. ::: | PIN&Connector | 功能 | | --------------------------------- | ----------------------------------------------------------------------------------------------------------- | | I/O PWM-IN | See note below for connection to _Pixhawk 4_ | | M1 | I/O PWM OUT 1：将信号线连接到到电机 1 的电调 | | M2 | I/O PWM OUT 2：将信号线连接到到电机 2 的电调 | | M3 | I/O PWM OUT 3：将信号线连接到到电机 3 的电调 | | M4 | I/O PWM OUT 4：将信号线连接到到电机 4 的电调 | | M5 | I/O PWM OUT 5：将信号线连接到到电机 5 的电调 | | M6 | I/O PWM OUT 6：将信号线连接到到电机 6 的电调 | | M7 | I/O PWM OUT 7：将信号线连接到到电机 7 的电调 | | M8 | I/O PWM OUT 8：将信号线连接到到电机 8 的电调 | | FMU PWM-IN | See note below for connection to _Pixhawk 4_ | | FMU PWM-OUT | If FMU PWM-IN is connected to _Pixhawk 4_, connect signal wires to ESC or signal, +, - wires to servos here | | CAP&ADC-OUT | connect to CAP & ADC IN port of _Pixhawk 4_ | | CAP&ADC-IN | CAP&ADC input: Pinouts are printed on the back side of the board | | B+ | 连接到 ESC电调B+以为 ESC电调供电 | | GND | 连接到 ESC电调负极 | | PWR1 | 5v output 3A, connect to _Pixhawk 4_ POWER 1 | | PWR2 | 5v output 3A, connect to _Pixhawk 4_ POWER 2 | | 2~12S | 电源输入，连接到12~S的LiPo电池 | :::info Depending on your airframe type, refer to [Airframe Reference](../airframes/airframe_reference.md) to connect **I/O PWM OUT** and **FMU PWM OUT** ports of _Pixhawk 4_ to PM board. **MAIN** outputs in PX4 firmware map to **I/O PWM OUT** port of _Pixhawk 4_ whereas **AUX outputs** map to **FMU PWM OUT** of _Pixhawk 4_. For example, **MAIN1** maps to IO_CH1 pin of **I/O PWM OUT** and **AUX1** maps to FMU_CH1 pin of **FMU PWM OUT**. **FMU PWM-IN** of PM board is internally connected to **FMU PWM-OUT**. **I/O PWM-IN** of PM board is internally connected to **M1-8**. ::: The following table summarizes how to connect _Pixhawk 4_'s PWM OUT ports to PM board's PWM-IN ports, depending on the Airframe Reference. | 机架参考 | Connection between _Pixhawk 4_ --> PM board | | ------------------------------- | ------------------------------------------- | | **MAIN**: motor | I/O PWM OUT --> I/O PWM IN | | **MAIN**: servo | I/O PWM OUT --> FMU PWM IN | | **AUX**: motor | FMU PWM OUT --> I/O PWM IN | | **AUX**: servo | FMU PWM OUT --> FMU PWM IN | The pinout of _Pixhawk 4_’s power ports is shown below. The CURRENT signal should carry an analog voltage from 0-3.3V for 0-120A as default. The VOLTAGE signal should carry an analog voltage from 0-3.3V for 0-60V as default. The VCC lines have to offer at least 3A continuous and should default to 5.1V. A lower voltage of 5V is still acceptable, but discouraged. | 针脚 | 信号 | 电压 | | ---- | --- | --------------------- | | 1（红） | VCC | +5V | | 2（黑） | VCC | +5V | | 3（黑） | 电流 | +3.3V | | 4（黑） | 电压 | +3.3V | | 5（黑） | GND | GND | | 6（黑） | GND | GND | :::info Using the Power Module that comes with the kit you will need to configure the _Number of Cells_ in the [Power Settings](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/setup_view/power.html) but you won't need to calibrate the _voltage divider_. You will have to update the _voltage divider_ if you are using any other power module (e.g. the one from the Pixracer). ::: ## 遥控器 A remote control (RC) radio system is required if you want to _manually_ control your vehicle (PX4 does not require a radio system for autonomous flight modes). You will need to [select a compatible transmitter/receiver](../getting_started/rc_transmitter_receiver.md) and then _bind_ them so that they communicate (read the instructions that come with your specific transmitter/receiver). The instructions below show how to connect the different types of receivers to _Pixhawk 4_: - Spektrum/DSM or S.BUS receivers connect to the **DSM/SBUS RC** input. ![Pixhawk 4 - Radio port for Spektrum receivers](../../assets/flight_controller/pixhawk4/pixhawk4_receiver_sbus.png) - PPM receivers connect to the **PPM RC** input port. ![Pixhawk 4 - Radio port for PPM receivers](../../assets/flight_controller/pixhawk4/pixhawk_4_receiver_ppm.png) - PPM and PWM receivers that have an _individual wire for each channel_ must connect to the **PPM RC** port _via a PPM encoder_ [like this one](https://www.getfpv.com/radios/radio-accessories/holybro-ppm-encoder-module.html) (PPM-Sum receivers use a single signal wire for all channels). For more information about selecting a radio system, receiver compatibility, and binding your transmitter/receiver pair, see: [Remote Control Transmitters & Receivers](../getting_started/rc_transmitter_receiver.md). ## Telemetry Radios (Optional) Telemetry radios may be used to communicate and control a vehicle in flight from a ground station (for example, you can direct the UAV to a particular position, or upload a new mission). The vehicle-based radio should be connected to the **TELEM1** port as shown below (if connected to this port, no further configuration is required). The other radio is connected to your ground station computer or mobile device (usually by USB). ![Pixhawk 4/Telemetry Radio](../../assets/flight_controller/pixhawk4/pixhawk4_telemetry_radio.jpg) ## SD Card (Optional) {#sd_card} SD cards are highly recommended as they are needed to [log and analyse flight details](../getting_started/flight_reporting.md), to run missions, and to use UAVCAN-bus hardware. Insert the card (included in Pixhawk 4 kit) into _Pixhawk 4_ as shown below. ![Pixhawk 4/SD Card](../../assets/flight_controller/pixhawk4/pixhawk4_sd_card.png) :::tip For more information see [Basic Concepts > SD Cards (Removable Memory)](../getting_started/px4_basic_concepts.md#sd-cards-removable-memory). ::: ## 电机 Motors/servos are connected to the **I/O PWM OUT** (**MAIN**) and **FMU PWM OUT** (**AUX**) ports in the order specified for your vehicle in the [Airframe Reference](../airframes/airframe_reference.md). :::info This reference lists the output port to motor/servo mapping for all supported air and ground frames (if your frame is not listed in the reference then use a "generic" airframe of the correct type). ::: :::warning The mapping is not consistent across frames (e.g. you can't rely on the throttle being on the same output for all plane frames). Make sure to use the correct mapping for your vehicle. ::: ## 其它外设 The wiring and configuration of optional/less common components is covered within the topics for individual [peripherals](../peripherals/index.md). ## 针脚定义 [Pixhawk 4 Pinouts](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-Pinouts.pdf) (Holybro) ## 配置 General configuration information is covered in: [Autopilot Configuration](../config/index.md). QuadPlane specific configuration is covered here: [QuadPlane VTOL Configuration](../config_vtol/vtol_quad_configuration.md) ## 更多信息 - [Pixhawk 4](../flight_controller/pixhawk4.md) (Overview page) - [Pixhawk 4 Technical Data Sheet](https://github.com/PX4/PX4-Autopilot/blob/main/docs/assets/flight_controller/pixhawk4/pixhawk4_technical_data_sheet.pdf) - [Pixhawk 4 Pinouts](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-Pinouts.pdf) (Holybro) - [Pixhawk 4 Quick Start Guide (Holybro)](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-quickstartguide.pdf)