# Durandal Wiring Quick Start
:::warning
PX4 does not manufacture this (or any) autopilot.
Contact the [manufacturer](https://holybro.com/) for hardware support or compliance issues.
:::
This quick start guide shows how to power the Holybro [Durandal](../flight_controller/durandal.md)® flight controller and connect its most important peripherals.
## Unboxing
Durandal is sold bundled with a number of different combinations of accessories, including power modules: _PM02 V3_ and _PM07_, and the _Pixhawk 4 GPS/Compass_ ( u-blox NEO-M8N).
The content of the box with the _PM02 V3_ power module is shown below (the box also includes a pinout guide and power module instructions).
## Wiring Chart Overview
The image below shows how to connect the most important sensors and peripherals (except the motor and servo outputs).
We'll go through each of these in detail in the following sections.
:::tip
More information about available ports can be found here: [Durandal > Pinouts](../flight_controller/durandal.md#pinouts).
:::
## Mount and Orient Controller
_Durandal_ should be mounted on the frame positioned as close to your vehicle’s center of gravity as possible, oriented top-side up with the arrow pointing towards the front of the vehicle.
If the controller cannot be mounted in the recommended/default orientation (e.g. due to space constraints) you will need to configure the autopilot software with the orientation that you actually used: [Flight Controller Orientation](../config/flight_controller_orientation.md).
:::tip
The board has internal vibration-isolation.
Do not use vibration-isolation foam to mount the controller (double sided tape is normally sufficient).
:::
## GPS + Compass + Buzzer + Safety Switch + LED
Durandal is designed to work well with the _Pixhawk 4 GPS module_, which has an integrated compass, safety switch, buzzer and LED.
It connects directly to the [GPS port](../flight_controller/durandal.md#gps) using the 10 pin cable.
The GPS/Compass should be mounted on the frame as far away from other electronics as possible, with the direction marker towards the front of the vehicle (separating the compass from other electronics will reduce interference).
::: info
The GPS module's integrated safety switch is enabled _by default_ (when enabled, PX4 will not let you arm the vehicle).
To disable the safety press and hold the safety switch for 1 second.
You can press the safety switch again to enable safety and disarm the vehicle (this can be useful if, for whatever reason, you are unable to disarm the vehicle from your remote control or ground station).
:::
## Power
You can use a power module or power distribution board to power motors/servos and measure power consumption.
The recommended power modules are shown below.
### PM02 v3 Power Module
The [Power Module (PM02 v3)](../power_module/holybro_pm02.md) can be bundled with _Durandal_.
It provides regulated power to flight controller and sends battery voltage/current to the flight controller.
Connect the output of the _Power Module_ as shown.
- PM voltage/current port: connect to [POWER1](../flight_controller/durandal.md#power) port (or `POWER2`) using the 6-wire GH cable supplied.
- PM input (XT60 male connector): connect to the LiPo battery (2~12S).
- PM power output (XT60 female connector): wire out to any motor ESCs.
:::tip
As this power module does not include power distribution wiring, you would normally just connect all the ESCs in parallel to the power module output (the ESC must be appropriate for the supplied voltage level).
:::
:::tip
The 8 pin power (+) rail of **MAIN/AUX** is not powered by the power module supply to the flight controller.
If it will need to be separately powered in order to drive servos for rudders, elevons etc., the power rail needs to be connected to a BEC equipped ESC or a standalone 5V BEC or a 2S LiPo battery.
Ensure the voltage of servo you are going to use is appropriate.
:::
The power module has the following characteristics/limits:
- Max input voltage: 60V
- Max current sensing: 120A Voltage
- Current measurement configured for SV ADC Switching regulator outputs 5.2V and 3A max
- Weight: 20g
- Package includes:
- PM02 board
- 6pin MLX cable (1)
- 6pin GH cable (1)
### Pixhawk 4 Power Module (PM07)
The [Pixhawk 4 Power Module (PM07)](https://holybro.com/collections/power-modules-pdbs/products/pixhawk-4-power-module-pm07) can be bundled/used with _Durandal_.
It acts as both a power module and power distribution board, providing regulated power to flight controller and the ESCs, and sending battery voltage/current to the flight controller.
This is wired up in the same way as described in the [Pixhawk 4 Quick Start > Power](../assembly/quick_start_pixhawk4.md#power) documentation.
It has the following characteristics/limits:
- PCB Current: total 120A outputs (MAX)
- UBEC 5V output current: 3A
- UBEC input voltage : 7~51v (2~12s LiPo)
- Dimensions: 68*50*8 mm
- Mounting Holes: 45\*45mm
- Weight: 36g
- Package includes:
- PM07 board (1)
- 80mm XT60 connector wire (1)
::: info
See also [PM07 Quick Start Guide](https://docs.holybro.com/power-module-and-pdb/power-module/pm07-quick-start-guide) (Holybro).
:::
### Battery Configuration
The battery/power setup must be configured in [Battery Estimation Tuning](../config/battery.md).
For either Power Module you will need to configure the _Number of Cells_.
You will not need to update the _voltage divider_ unless you are using some other power module (e.g. the one from the Pixracer).
## Radio Control
A remote control (RC) radio system is required if you want to _manually_ control your vehicle (PX4 does not require a radio system for autonomous flight modes).
You will need to [select a compatible transmitter/receiver](../getting_started/rc_transmitter_receiver.md) and then _bind_ them so that they communicate (read the instructions that come with your specific transmitter/receiver).
The instructions below show how to connect the different types of receivers to _Durandal_:
- Spektrum/DSM receivers connect to the [DSM RC](../flight_controller/durandal.md#dsm-rc-port) input.
- PPM and S.Bus receivers connect to the [SBUS_IN/PPM_IN](../flight_controller/durandal.md#rc-in) input port (marked as RC IN, next to the MAIN/AUX inputs).
- PPM and PWM receivers that have an _individual wire for each channel_ must connect to the **PPM RC** port _via a PPM encoder_ [like this one](https://www.getfpv.com/radios/radio-accessories/holybro-ppm-encoder-module.html) (PPM-Sum receivers use a single signal wire for all channels).
For more information about selecting a radio system, receiver compatibility, and binding your transmitter/receiver pair, see: [Remote Control Transmitters & Receivers](../getting_started/rc_transmitter_receiver.md).
## Telemetry Radios (Optional)
Telemetry radios may be used to communicate and control a vehicle in flight from a ground station (for example, you can direct the UAV to a particular position, or upload a new mission).
The vehicle-based radio should be connected to the [TELEM1](../flight_controller/durandal.md#telem1_2_3) port as shown below using one of the 6-pos connectors (if connected to this port, no further configuration is required).
The other radio is connected to your ground station computer or mobile device (usually by USB).
## SD Card (Optional)
SD cards are highly recommended as they are needed to [log and analyse flight details](../getting_started/flight_reporting.md), to run missions, and to use UAVCAN-bus hardware.
Insert an SD card into the _Durandal_ where indicated below.
:::tip
For more information see [Basic Concepts > SD Cards (Removable Memory)](../getting_started/px4_basic_concepts.md#sd-cards-removable-memory).
:::
## Motors
Motors/servos control signals are connected to the **I/O PWM OUT** (**MAIN OUT**) and **FMU PWM OUT** (**AUX**) ports in the order specified for your vehicle in the [Airframe Reference](../airframes/airframe_reference.md).
The motors must be separately [powered](#power).
::: info
If your frame is not listed in the airframe reference then use a "generic" airframe of the correct type.
:::
:::tip
_Durandal_ has 5 AUX ports, so cannot be used with airframes that map AUX6, AUX7, AUX8 to motors or other critical flight controls.
:::
## Other Peripherals
The wiring and configuration of optional/less common components is covered within the topics for individual [peripherals](../peripherals/index.md).
## Pinouts
[Durandal > Pinouts](../flight_controller/durandal.md#pinouts)
## PX4 Configuration
First you will need to install [PX4 "Master" Firmware](../config/firmware.md#custom) onto the controller using _QGroundControl_.
::: info
Durandal support will be in the _stable_ PX4 release that follows PX4 v1.10.
:::
Further general configuration information is covered in: [Autopilot Configuration](../config/index.md).
QuadPlane specific configuration is covered here: [QuadPlane VTOL Configuration](../config_vtol/vtol_quad_configuration.md)
## Further information
- [Durandal Overview](../flight_controller/durandal.md)
- [Durandal Technical Data Sheet](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Durandal_technical_data_sheet_90f8875d-8035-4632-a936-a0d178062077.pdf) (Holybro)
- [Durandal Pinouts](https://cdn.shopifycdn.net/s/files/1/0604/5905/7341/files/Durandal_Pinouts_v1.0.pdf?v=1693983344) (Holybro)
- [Durandal_MB_H743sch.pdf](https://github.com/PX4/PX4-Autopilot/raw/main/docs/assets/flight_controller/durandal/Durandal_MB_H743sch.pdf) (Durandal Schematics)
- [STM32H743IIK_pinout.pdf](https://github.com/PX4/PX4-Autopilot/raw/main/docs/assets/flight_controller/durandal/STM32H743IIK_pinout.pdf) (Durandal Pinmap)