fly316/PX4-Autopilot
7
0
Fork 0
mirror of https://gitee.com/mirrors_PX4/PX4-Autopilot.git synced 2026-10-19 05:53:34 +08:00
Code Issues Packages Projects Releases Wiki Activity

Merged master into lockdown_disable

Browse Source
This commit is contained in:
Lorenz Meier
2014-01-30 10:00:01 +01:00
parent 62076c0e81 3b31a6b1b9
commit ff753b9e24
98 changed files with 2764 additions and 2745 deletions
Download Patch File Download Diff File Expand all files Collapse all files
src/modules/px4iofirmware/adc.c
+23 -30
View File
@@ -83,6 +83,14 @@ adc_init(void)
{
adc_perf = perf_alloc(PC_ELAPSED, "adc");
/* put the ADC into power-down mode */
rCR2 &= ~ADC_CR2_ADON;
up_udelay(10);
/* bring the ADC out of power-down mode */
rCR2 |= ADC_CR2_ADON;
up_udelay(10);
/* do calibration if supported */
#ifdef ADC_CR2_CAL
rCR2 |= ADC_CR2_RSTCAL;
@@ -96,41 +104,25 @@ adc_init(void)
if (rCR2 & ADC_CR2_CAL)
return -1;
#endif
/* arbitrarily configure all channels for 55 cycle sample time */
rSMPR1 = 0b00000011011011011011011011011011;
/*
* Configure sampling time.
*
* For electrical protection reasons, we want to be able to have
* 10K in series with ADC inputs that leave the board. At 12MHz this
* means we need 28.5 cycles of sampling time (per table 43 in the
* datasheet).
*/
rSMPR1 = 0b00000000011011011011011011011011;
rSMPR2 = 0b00011011011011011011011011011011;
/* XXX for F2/4, might want to select 12-bit mode? */
rCR1 = 0;
/* enable the temperature sensor / Vrefint channel if supported*/
rCR2 =
#ifdef ADC_CR2_TSVREFE
/* enable the temperature sensor in CR2 */
ADC_CR2_TSVREFE |
#endif
0;
#ifdef ADC_CCR_TSVREFE
/* enable temperature sensor in CCR */
rCCR = ADC_CCR_TSVREFE;
#endif
rCR2 |= ADC_CR2_TSVREFE; /* enable the temperature sensor / Vrefint channel */
/* configure for a single-channel sequence */
rSQR1 = 0;
rSQR2 = 0;
rSQR3 = 0; /* will be updated with the channel each tick */
/* power-cycle the ADC and turn it on */
rCR2 &= ~ADC_CR2_ADON;
up_udelay(10);
rCR2 |= ADC_CR2_ADON;
up_udelay(10);
rCR2 |= ADC_CR2_ADON;
up_udelay(10);
rSQR3 = 0; /* will be updated with the channel at conversion time */
return 0;
}
@@ -141,11 +133,12 @@ adc_init(void)
uint16_t
adc_measure(unsigned channel)
{
perf_begin(adc_perf);
/* clear any previous EOC */
if (rSR & ADC_SR_EOC)
rSR &= ~ADC_SR_EOC;
rSR = 0;
(void)rDR;
/* run a single conversion right now - should take about 60 cycles (a few microseconds) max */
rSQR3 = channel;
@@ -158,7 +151,6 @@ adc_measure(unsigned channel)
/* never spin forever - this will give a bogus result though */
if (hrt_elapsed_time(&now) > 100) {
debug("adc timeout");
perf_end(adc_perf);
return 0xffff;
}
@@ -166,6 +158,7 @@ adc_measure(unsigned channel)
/* read the result and clear EOC */
uint16_t result = rDR;
rSR = 0;
perf_end(adc_perf);
return result;
src/modules/px4iofirmware/controls.c
+139 -83
View File
@@ -1,6 +1,6 @@
/****************************************************************************
*
* Copyright (C) 2012 PX4 Development Team. All rights reserved.
* Copyright (c) 2012-2014 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
@@ -59,6 +59,11 @@ static perf_counter_t c_gather_ppm;
void
controls_init(void)
{
/* no channels */
r_raw_rc_count = 0;
system_state.rc_channels_timestamp_received = 0;
system_state.rc_channels_timestamp_valid = 0;
/* DSM input (USART1) */
dsm_init("/dev/ttyS0");
@@ -97,26 +102,64 @@ controls_tick() {
/* receive signal strenght indicator (RSSI). 0 = no connection, 255: perfect connection */
uint16_t rssi = 0;
#ifdef ADC_RSSI
if (r_setup_features & PX4IO_P_SETUP_FEATURES_ADC_RSSI) {
unsigned counts = adc_measure(ADC_RSSI);
if (counts != 0xffff) {
/* use 1:1 scaling on 3.3V ADC input */
unsigned mV = counts * 3300 / 4096;
/* scale to 0..253 */
rssi = mV / 13;
}
}
#endif
perf_begin(c_gather_dsm);
uint16_t temp_count = r_raw_rc_count;
bool dsm_updated = dsm_input(r_raw_rc_values, &temp_count);
if (dsm_updated) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_DSM;
r_raw_rc_flags |= PX4IO_P_STATUS_FLAGS_RC_DSM;
r_raw_rc_count = temp_count & 0x7fff;
if (temp_count & 0x8000)
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_DSM11;
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_RC_DSM11;
else
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_RC_DSM11;
r_raw_rc_flags &= ~PX4IO_P_RAW_RC_FLAGS_RC_DSM11;
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FRAME_DROP);
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FAILSAFE);
rssi = 255;
}
perf_end(c_gather_dsm);
perf_begin(c_gather_sbus);
bool sbus_updated = sbus_input(r_raw_rc_values, &r_raw_rc_count, &rssi, PX4IO_RC_INPUT_CHANNELS);
bool sbus_status = (r_status_flags & PX4IO_P_STATUS_FLAGS_RC_SBUS);
bool sbus_failsafe, sbus_frame_drop;
bool sbus_updated = sbus_input(r_raw_rc_values, &r_raw_rc_count, &sbus_failsafe, &sbus_frame_drop, PX4IO_RC_INPUT_CHANNELS);
if (sbus_updated) {
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_SBUS;
rssi = 255;
if (sbus_frame_drop) {
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_FRAME_DROP;
rssi = 100;
} else {
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FRAME_DROP);
}
if (sbus_failsafe) {
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_FAILSAFE;
rssi = 0;
} else {
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FAILSAFE);
}
}
perf_end(c_gather_sbus);
/*
@@ -125,13 +168,12 @@ controls_tick() {
* disable the PPM decoder completely if we have S.bus signal.
*/
perf_begin(c_gather_ppm);
bool ppm_updated = ppm_input(r_raw_rc_values, &r_raw_rc_count, &r_page_status[PX4IO_P_STATUS_RC_DATA]);
bool ppm_updated = ppm_input(r_raw_rc_values, &r_raw_rc_count, &r_page_raw_rc_input[PX4IO_P_RAW_RC_DATA]);
if (ppm_updated) {
/* XXX sample RSSI properly here */
rssi = 255;
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_PPM;
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FRAME_DROP);
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_FAILSAFE);
}
perf_end(c_gather_ppm);
@@ -139,6 +181,9 @@ controls_tick() {
if (r_raw_rc_count > PX4IO_RC_INPUT_CHANNELS)
r_raw_rc_count = PX4IO_RC_INPUT_CHANNELS;
/* store RSSI */
r_page_raw_rc_input[PX4IO_P_RAW_RC_NRSSI] = rssi;
/*
* In some cases we may have received a frame, but input has still
* been lost.
@@ -150,97 +195,100 @@ controls_tick() {
*/
if (dsm_updated || sbus_updated || ppm_updated) {
/* update RC-received timestamp */
system_state.rc_channels_timestamp = hrt_absolute_time();
/* record a bitmask of channels assigned */
unsigned assigned_channels = 0;
/* map raw inputs to mapped inputs */
/* XXX mapping should be atomic relative to protocol */
for (unsigned i = 0; i < r_raw_rc_count; i++) {
/* update RC-received timestamp */
system_state.rc_channels_timestamp_received = hrt_absolute_time();
/* map the input channel */
uint16_t *conf = &r_page_rc_input_config[i * PX4IO_P_RC_CONFIG_STRIDE];
/* do not command anything in failsafe, kick in the RC loss counter */
if (!(r_raw_rc_flags & PX4IO_P_RAW_RC_FLAGS_FAILSAFE)) {
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_ENABLED) {
/* update RC-received timestamp */
system_state.rc_channels_timestamp_valid = system_state.rc_channels_timestamp_received;
uint16_t raw = r_raw_rc_values[i];
/* map raw inputs to mapped inputs */
/* XXX mapping should be atomic relative to protocol */
for (unsigned i = 0; i < r_raw_rc_count; i++) {
int16_t scaled;
/* map the input channel */
uint16_t *conf = &r_page_rc_input_config[i * PX4IO_P_RC_CONFIG_STRIDE];
/*
* 1) Constrain to min/max values, as later processing depends on bounds.
*/
if (raw < conf[PX4IO_P_RC_CONFIG_MIN])
raw = conf[PX4IO_P_RC_CONFIG_MIN];
if (raw > conf[PX4IO_P_RC_CONFIG_MAX])
raw = conf[PX4IO_P_RC_CONFIG_MAX];
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_ENABLED) {
/*
* 2) Scale around the mid point differently for lower and upper range.
*
* This is necessary as they don't share the same endpoints and slope.
*
* First normalize to 0..1 range with correct sign (below or above center),
* then scale to 20000 range (if center is an actual center, -10000..10000,
* if parameters only support half range, scale to 10000 range, e.g. if
* center == min 0..10000, if center == max -10000..0).
*
* As the min and max bounds were enforced in step 1), division by zero
* cannot occur, as for the case of center == min or center == max the if
* statement is mutually exclusive with the arithmetic NaN case.
*
* DO NOT REMOVE OR ALTER STEP 1!
*/
if (raw > (conf[PX4IO_P_RC_CONFIG_CENTER] + conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_MAX] - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]));
uint16_t raw = r_raw_rc_values[i];
} else if (raw < (conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] + conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE] - conf[PX4IO_P_RC_CONFIG_MIN]));
int16_t scaled;
} else {
/* in the configured dead zone, output zero */
scaled = 0;
}
/*
* 1) Constrain to min/max values, as later processing depends on bounds.
*/
if (raw < conf[PX4IO_P_RC_CONFIG_MIN])
raw = conf[PX4IO_P_RC_CONFIG_MIN];
if (raw > conf[PX4IO_P_RC_CONFIG_MAX])
raw = conf[PX4IO_P_RC_CONFIG_MAX];
/* invert channel if requested */
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_REVERSE)
scaled = -scaled;
/*
* 2) Scale around the mid point differently for lower and upper range.
*
* This is necessary as they don't share the same endpoints and slope.
*
* First normalize to 0..1 range with correct sign (below or above center),
* then scale to 20000 range (if center is an actual center, -10000..10000,
* if parameters only support half range, scale to 10000 range, e.g. if
* center == min 0..10000, if center == max -10000..0).
*
* As the min and max bounds were enforced in step 1), division by zero
* cannot occur, as for the case of center == min or center == max the if
* statement is mutually exclusive with the arithmetic NaN case.
*
* DO NOT REMOVE OR ALTER STEP 1!
*/
if (raw > (conf[PX4IO_P_RC_CONFIG_CENTER] + conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_MAX] - conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE]));
/* and update the scaled/mapped version */
unsigned mapped = conf[PX4IO_P_RC_CONFIG_ASSIGNMENT];
if (mapped < PX4IO_CONTROL_CHANNELS) {
} else if (raw < (conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE])) {
scaled = 10000.0f * ((raw - conf[PX4IO_P_RC_CONFIG_CENTER] + conf[PX4IO_P_RC_CONFIG_DEADZONE]) / (float)(conf[PX4IO_P_RC_CONFIG_CENTER] - conf[PX4IO_P_RC_CONFIG_DEADZONE] - conf[PX4IO_P_RC_CONFIG_MIN]));
/* invert channel if pitch - pulling the lever down means pitching up by convention */
if (mapped == 1) /* roll, pitch, yaw, throttle, override is the standard order */
} else {
/* in the configured dead zone, output zero */
scaled = 0;
}
/* invert channel if requested */
if (conf[PX4IO_P_RC_CONFIG_OPTIONS] & PX4IO_P_RC_CONFIG_OPTIONS_REVERSE)
scaled = -scaled;
r_rc_values[mapped] = SIGNED_TO_REG(scaled);
assigned_channels |= (1 << mapped);
/* and update the scaled/mapped version */
unsigned mapped = conf[PX4IO_P_RC_CONFIG_ASSIGNMENT];
if (mapped < PX4IO_CONTROL_CHANNELS) {
/* invert channel if pitch - pulling the lever down means pitching up by convention */
if (mapped == 1) /* roll, pitch, yaw, throttle, override is the standard order */
scaled = -scaled;
r_rc_values[mapped] = SIGNED_TO_REG(scaled);
assigned_channels |= (1 << mapped);
}
}
}
}
/* set un-assigned controls to zero */
for (unsigned i = 0; i < PX4IO_CONTROL_CHANNELS; i++) {
if (!(assigned_channels & (1 << i)))
r_rc_values[i] = 0;
}
/* set un-assigned controls to zero */
for (unsigned i = 0; i < PX4IO_CONTROL_CHANNELS; i++) {
if (!(assigned_channels & (1 << i)))
r_rc_values[i] = 0;
}
/*
* If we got an update with zero channels, treat it as
* a loss of input.
*
* This might happen if a protocol-based receiver returns an update
* that contains no channels that we have mapped.
*/
if (assigned_channels == 0 || rssi == 0) {
rc_input_lost = true;
} else {
/* set RC OK flag */
/* set RC OK flag, as we got an update */
r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_OK;
/* if we have enough channels (5) to control the vehicle, the mapping is ok */
if (assigned_channels > 4) {
r_raw_rc_flags |= PX4IO_P_RAW_RC_FLAGS_MAPPING_OK;
} else {
r_raw_rc_flags &= ~(PX4IO_P_RAW_RC_FLAGS_MAPPING_OK);
}
}
/*
@@ -253,7 +301,7 @@ controls_tick() {
* If we haven't seen any new control data in 200ms, assume we
* have lost input.
*/
if (hrt_elapsed_time(&system_state.rc_channels_timestamp) > 200000) {
if (hrt_elapsed_time(&system_state.rc_channels_timestamp_received) > 200000) {
rc_input_lost = true;
/* clear the input-kind flags here */
@@ -261,24 +309,32 @@ controls_tick() {
PX4IO_P_STATUS_FLAGS_RC_PPM |
PX4IO_P_STATUS_FLAGS_RC_DSM |
PX4IO_P_STATUS_FLAGS_RC_SBUS);
}
/*
* Handle losing RC input
*/
if (rc_input_lost) {
/* this kicks in if the receiver is gone or the system went to failsafe */
if (rc_input_lost || (r_raw_rc_flags & PX4IO_P_RAW_RC_FLAGS_FAILSAFE)) {
/* Clear the RC input status flag, clear manual override flag */
r_status_flags &= ~(
PX4IO_P_STATUS_FLAGS_OVERRIDE |
PX4IO_P_STATUS_FLAGS_RC_OK);
/* Mark all channels as invalid, as we just lost the RX */
r_rc_valid = 0;
/* Set the RC_LOST alarm */
r_status_alarms |= PX4IO_P_STATUS_ALARMS_RC_LOST;
}
/* Mark the arrays as empty */
/* this kicks in if the receiver is completely gone */
if (rc_input_lost) {
/* Set channel count to zero */
r_raw_rc_count = 0;
r_rc_valid = 0;
}
/*
src/modules/px4iofirmware/mixer.cpp
+23 -7
View File
@@ -1,6 +1,6 @@
/****************************************************************************
*
* Copyright (C) 2012 PX4 Development Team. All rights reserved.
* Copyright (c) 2012-2014 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
@@ -71,6 +71,7 @@ extern "C" {
static bool mixer_servos_armed = false;
static bool should_arm = false;
static bool should_always_enable_pwm = false;
static volatile bool in_mixer = false;
/* selected control values and count for mixing */
enum mixer_source {
@@ -95,6 +96,7 @@ static void mixer_set_failsafe();
void
mixer_tick(void)
{
/* check that we are receiving fresh data from the FMU */
if (hrt_elapsed_time(&system_state.fmu_data_received_time) > FMU_INPUT_DROP_LIMIT_US) {
@@ -199,13 +201,17 @@ mixer_tick(void)
}
} else if (source != MIX_NONE) {
} else if (source != MIX_NONE && (r_status_flags & PX4IO_P_STATUS_FLAGS_MIXER_OK)) {
float outputs[PX4IO_SERVO_COUNT];
unsigned mixed;
/* mix */
/* poor mans mutex */
in_mixer = true;
mixed = mixer_group.mix(&outputs[0], PX4IO_SERVO_COUNT);
in_mixer = false;
pwm_limit_calc(should_arm, mixed, r_page_servo_disarmed, r_page_servo_control_min, r_page_servo_control_max, outputs, r_page_servos, &pwm_limit);
@@ -308,12 +314,17 @@ mixer_callback(uintptr_t handle,
static char mixer_text[256]; /* large enough for one mixer */
static unsigned mixer_text_length = 0;
void
int
mixer_handle_text(const void *buffer, size_t length)
{
/* do not allow a mixer change while safety off */
if ((r_status_flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF)) {
return;
return 1;
}
/* abort if we're in the mixer */
if (in_mixer) {
return 1;
}
px4io_mixdata *msg = (px4io_mixdata *)buffer;
@@ -321,7 +332,7 @@ mixer_handle_text(const void *buffer, size_t length)
isr_debug(2, "mix txt %u", length);
if (length < sizeof(px4io_mixdata))
return;
return 0;
unsigned text_length = length - sizeof(px4io_mixdata);
@@ -339,13 +350,16 @@ mixer_handle_text(const void *buffer, size_t length)
case F2I_MIXER_ACTION_APPEND:
isr_debug(2, "append %d", length);
/* disable mixing during the update */
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_MIXER_OK;
/* check for overflow - this would be really fatal */
if ((mixer_text_length + text_length + 1) > sizeof(mixer_text)) {
r_status_flags &= ~PX4IO_P_STATUS_FLAGS_MIXER_OK;
return;
return 0;
}
/* append mixer text and nul-terminate */
/* append mixer text and nul-terminate, guard against overflow */
memcpy(&mixer_text[mixer_text_length], msg->text, text_length);
mixer_text_length += text_length;
mixer_text[mixer_text_length] = '\0';
@@ -380,6 +394,8 @@ mixer_handle_text(const void *buffer, size_t length)
break;
}
return 0;
}
static void
src/modules/px4iofirmware/protocol.h
+15 -4
View File
@@ -111,7 +111,6 @@
#define PX4IO_P_STATUS_FLAGS_INIT_OK (1 << 10) /* initialisation of the IO completed without error */
#define PX4IO_P_STATUS_FLAGS_FAILSAFE (1 << 11) /* failsafe is active */
#define PX4IO_P_STATUS_FLAGS_SAFETY_OFF (1 << 12) /* safety is off */
#define PX4IO_P_STATUS_FLAGS_RC_DSM11 (1 << 13) /* DSM input is 11 bit data */
#define PX4IO_P_STATUS_ALARMS 3 /* alarm flags - alarms latch, write 1 to a bit to clear it */
#define PX4IO_P_STATUS_ALARMS_VBATT_LOW (1 << 0) /* [1] VBatt is very close to regulator dropout */
@@ -128,8 +127,6 @@
#define PX4IO_P_STATUS_VSERVO 6 /* [2] servo rail voltage in mV */
#define PX4IO_P_STATUS_VRSSI 7 /* [2] RSSI voltage */
#define PX4IO_P_STATUS_PRSSI 8 /* [2] RSSI PWM value */
#define PX4IO_P_STATUS_NRSSI 9 /* [2] Normalized RSSI value, 0: no reception, 255: perfect reception */
#define PX4IO_P_STATUS_RC_DATA 10 /* [1] + [2] Details about the RC source (PPM frame length, Spektrum protocol type) */
/* array of post-mix actuator outputs, -10000..10000 */
#define PX4IO_PAGE_ACTUATORS 2 /* 0..CONFIG_ACTUATOR_COUNT-1 */
@@ -140,7 +137,17 @@
/* array of raw RC input values, microseconds */
#define PX4IO_PAGE_RAW_RC_INPUT 4
#define PX4IO_P_RAW_RC_COUNT 0 /* number of valid channels */
#define PX4IO_P_RAW_RC_BASE 1 /* CONFIG_RC_INPUT_COUNT channels from here */
#define PX4IO_P_RAW_RC_FLAGS 1 /* RC detail status flags */
#define PX4IO_P_RAW_RC_FLAGS_FRAME_DROP (1 << 0) /* single frame drop */
#define PX4IO_P_RAW_RC_FLAGS_FAILSAFE (1 << 1) /* receiver is in failsafe mode */
#define PX4IO_P_RAW_RC_FLAGS_RC_DSM11 (1 << 2) /* DSM decoding is 11 bit mode */
#define PX4IO_P_RAW_RC_FLAGS_MAPPING_OK (1 << 3) /* Channel mapping is ok */
#define PX4IO_P_RAW_RC_NRSSI 2 /* [2] Normalized RSSI value, 0: no reception, 255: perfect reception */
#define PX4IO_P_RAW_RC_DATA 3 /* [1] + [2] Details about the RC source (PPM frame length, Spektrum protocol type) */
#define PX4IO_P_RAW_FRAME_COUNT 4 /* Number of total received frames (wrapping counter) */
#define PX4IO_P_RAW_LOST_FRAME_COUNT 5 /* Number of total dropped frames (wrapping counter) */
#define PX4IO_P_RAW_RC_BASE 6 /* CONFIG_RC_INPUT_COUNT channels from here */
/* array of scaled RC input values, -10000..10000 */
#define PX4IO_PAGE_RC_INPUT 5
@@ -157,6 +164,10 @@
/* setup page */
#define PX4IO_PAGE_SETUP 50
#define PX4IO_P_SETUP_FEATURES 0
#define PX4IO_P_SETUP_FEATURES_SBUS1_OUT (1 << 0) /* enable S.Bus v1 output */
#define PX4IO_P_SETUP_FEATURES_SBUS2_OUT (1 << 1) /* enable S.Bus v2 output */
#define PX4IO_P_SETUP_FEATURES_PWM_RSSI (1 << 2) /* enable PWM RSSI parsing */
#define PX4IO_P_SETUP_FEATURES_ADC_RSSI (1 << 3) /* enable ADC RSSI parsing */
#define PX4IO_P_SETUP_ARMING 1 /* arming controls */
#define PX4IO_P_SETUP_ARMING_IO_ARM_OK (1 << 0) /* OK to arm the IO side */
src/modules/px4iofirmware/px4io.c
+43 -18
View File
@@ -1,6 +1,6 @@
/****************************************************************************
*
* Copyright (C) 2012 PX4 Development Team. All rights reserved.
* Copyright (c) 2012-2014 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
@@ -196,6 +196,11 @@ user_start(int argc, char *argv[])
POWER_SERVO(true);
#endif
/* turn off S.Bus out (if supported) */
#ifdef ENABLE_SBUS_OUT
ENABLE_SBUS_OUT(false);
#endif
/* start the safety switch handler */
safety_init();
@@ -205,6 +210,9 @@ user_start(int argc, char *argv[])
/* initialise the control inputs */
controls_init();
/* set up the ADC */
adc_init();
/* start the FMU interface */
interface_init();
@@ -223,24 +231,41 @@ user_start(int argc, char *argv[])
/* initialize PWM limit lib */
pwm_limit_init(&pwm_limit);
#if 0
/* not enough memory, lock down */
if (minfo.mxordblk < 500) {
/*
* P O L I C E L I G H T S
*
* Not enough memory, lock down.
*
* We might need to allocate mixers later, and this will
* ensure that a developer doing a change will notice
* that he just burned the remaining RAM with static
* allocations. We don't want him to be able to
* get past that point. This needs to be clearly
* documented in the dev guide.
*
*/
if (minfo.mxordblk < 600) {
lowsyslog("ERR: not enough MEM");
bool phase = false;
if (phase) {
LED_AMBER(true);
LED_BLUE(false);
} else {
LED_AMBER(false);
LED_BLUE(true);
}
while (true) {
phase = !phase;
usleep(300000);
if (phase) {
LED_AMBER(true);
LED_BLUE(false);
} else {
LED_AMBER(false);
LED_BLUE(true);
}
up_udelay(250000);
phase = !phase;
}
}
#endif
/* Start the failsafe led init */
failsafe_led_init();
/*
* Run everything in a tight loop.
@@ -270,11 +295,12 @@ user_start(int argc, char *argv[])
check_reboot();
#if 0
/* check for debug activity */
/* check for debug activity (default: none) */
show_debug_messages();
/* post debug state at ~1Hz */
/* post debug state at ~1Hz - this is via an auxiliary serial port
* DEFAULTS TO OFF!
*/
if (hrt_absolute_time() - last_debug_time > (1000 * 1000)) {
struct mallinfo minfo = mallinfo();
@@ -287,7 +313,6 @@ user_start(int argc, char *argv[])
(unsigned)minfo.mxordblk);
last_debug_time = hrt_absolute_time();
}
#endif
}
}
src/modules/px4iofirmware/px4io.h
+9 -5
View File
@@ -1,6 +1,6 @@
/****************************************************************************
*
* Copyright (C) 2012 PX4 Development Team. All rights reserved.
* Copyright (c) 2012-2014 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
@@ -96,8 +96,9 @@ extern uint16_t r_page_servo_disarmed[]; /* PX4IO_PAGE_DISARMED_PWM */
#define r_raw_rc_count r_page_raw_rc_input[PX4IO_P_RAW_RC_COUNT]
#define r_raw_rc_values (&r_page_raw_rc_input[PX4IO_P_RAW_RC_BASE])
#define r_raw_rc_flags r_page_raw_rc_input[PX4IO_P_RAW_RC_FLAGS]
#define r_rc_valid r_page_rc_input[PX4IO_P_RC_VALID]
#define r_rc_values (&r_page_rc_input[PX4IO_P_RAW_RC_BASE])
#define r_rc_values (&r_page_rc_input[PX4IO_P_RC_BASE])
#define r_setup_features r_page_setup[PX4IO_P_SETUP_FEATURES]
#define r_setup_arming r_page_setup[PX4IO_P_SETUP_ARMING]
@@ -115,7 +116,8 @@ extern uint16_t r_page_servo_disarmed[]; /* PX4IO_PAGE_DISARMED_PWM */
*/
struct sys_state_s {
volatile uint64_t rc_channels_timestamp;
volatile uint64_t rc_channels_timestamp_received;
volatile uint64_t rc_channels_timestamp_valid;
/**
* Last FMU receive time, in microseconds since system boot
@@ -160,6 +162,7 @@ extern pwm_limit_t pwm_limit;
# define PX4IO_RELAY_CHANNELS 0
# define POWER_SPEKTRUM(_s) stm32_gpiowrite(GPIO_SPEKTRUM_PWR_EN, (_s))
# define ENABLE_SBUS_OUT(_s) stm32_gpiowrite(GPIO_SBUS_OENABLE, !(_s))
# define VDD_SERVO_FAULT (!stm32_gpioread(GPIO_SERVO_FAULT_DETECT))
@@ -177,12 +180,13 @@ extern pwm_limit_t pwm_limit;
* Mixer
*/
extern void mixer_tick(void);
extern void mixer_handle_text(const void *buffer, size_t length);
extern int mixer_handle_text(const void *buffer, size_t length);
/**
* Safety switch/LED.
*/
extern void safety_init(void);
extern void failsafe_led_init(void);
/**
* FMU communications
@@ -213,7 +217,7 @@ extern int dsm_init(const char *device);
extern bool dsm_input(uint16_t *values, uint16_t *num_values);
extern void dsm_bind(uint16_t cmd, int pulses);
extern int sbus_init(const char *device);
extern bool sbus_input(uint16_t *values, uint16_t *num_values, uint16_t *rssi, uint16_t max_channels);
extern bool sbus_input(uint16_t *values, uint16_t *num_values, bool *sbus_failsafe, bool *sbus_frame_drop, uint16_t max_channels);
/** global debug level for isr_debug() */
extern volatile uint8_t debug_level;
src/modules/px4iofirmware/registers.c
+53 -10
View File
@@ -90,8 +90,6 @@ uint16_t r_page_status[] = {
[PX4IO_P_STATUS_VSERVO] = 0,
[PX4IO_P_STATUS_VRSSI] = 0,
[PX4IO_P_STATUS_PRSSI] = 0,
[PX4IO_P_STATUS_NRSSI] = 0,
[PX4IO_P_STATUS_RC_DATA] = 0
};
/**
@@ -116,6 +114,12 @@ uint16_t r_page_servos[PX4IO_SERVO_COUNT];
uint16_t r_page_raw_rc_input[] =
{
[PX4IO_P_RAW_RC_COUNT] = 0,
[PX4IO_P_RAW_RC_FLAGS] = 0,
[PX4IO_P_RAW_RC_NRSSI] = 0,
[PX4IO_P_RAW_RC_DATA] = 0,
[PX4IO_P_RAW_FRAME_COUNT] = 0,
[PX4IO_P_RAW_LOST_FRAME_COUNT] = 0,
[PX4IO_P_RAW_RC_DATA] = 0,
[PX4IO_P_RAW_RC_BASE ... (PX4IO_P_RAW_RC_BASE + PX4IO_RC_INPUT_CHANNELS)] = 0
};
@@ -144,7 +148,12 @@ uint16_t r_page_scratch[32];
*/
volatile uint16_t r_page_setup[] =
{
#ifdef CONFIG_ARCH_BOARD_PX4IO_V2
/* default to RSSI ADC functionality */
[PX4IO_P_SETUP_FEATURES] = PX4IO_P_SETUP_FEATURES_ADC_RSSI,
#else
[PX4IO_P_SETUP_FEATURES] = 0,
#endif
[PX4IO_P_SETUP_ARMING] = 0,
[PX4IO_P_SETUP_PWM_RATES] = 0,
[PX4IO_P_SETUP_PWM_DEFAULTRATE] = 50,
@@ -162,7 +171,14 @@ volatile uint16_t r_page_setup[] =
[PX4IO_P_SETUP_CRC ... (PX4IO_P_SETUP_CRC+1)] = 0,
};
#define PX4IO_P_SETUP_FEATURES_VALID (0)
#ifdef CONFIG_ARCH_BOARD_PX4IO_V2
#define PX4IO_P_SETUP_FEATURES_VALID (PX4IO_P_SETUP_FEATURES_SBUS1_OUT | \
PX4IO_P_SETUP_FEATURES_SBUS2_OUT | \
PX4IO_P_SETUP_FEATURES_ADC_RSSI | \
PX4IO_P_SETUP_FEATURES_PWM_RSSI)
#else
#define PX4IO_P_SETUP_FEATURES_VALID 0
#endif
#define PX4IO_P_SETUP_ARMING_VALID (PX4IO_P_SETUP_ARMING_FMU_ARMED | \
PX4IO_P_SETUP_ARMING_MANUAL_OVERRIDE_OK | \
PX4IO_P_SETUP_ARMING_INAIR_RESTART_OK | \
@@ -383,7 +399,10 @@ registers_set(uint8_t page, uint8_t offset, const uint16_t *values, unsigned num
/* handle text going to the mixer parser */
case PX4IO_PAGE_MIXERLOAD:
mixer_handle_text(values, num_values * sizeof(*values));
if (!(r_status_flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) ||
(r_status_flags & PX4IO_P_STATUS_FLAGS_OUTPUTS_ARMED)) {
return mixer_handle_text(values, num_values * sizeof(*values));
}
break;
default:
@@ -436,9 +455,35 @@ registers_set_one(uint8_t page, uint8_t offset, uint16_t value)
case PX4IO_P_SETUP_FEATURES:
value &= PX4IO_P_SETUP_FEATURES_VALID;
r_setup_features = value;
/* no implemented feature selection at this point */
/* some of the options conflict - give S.BUS out precedence, then ADC RSSI, then PWM RSSI */
/* switch S.Bus output pin as needed */
#ifdef ENABLE_SBUS_OUT
ENABLE_SBUS_OUT(value & (PX4IO_P_SETUP_FEATURES_SBUS1_OUT | PX4IO_P_SETUP_FEATURES_SBUS2_OUT));
/* disable the conflicting options */
if (value & (PX4IO_P_SETUP_FEATURES_SBUS1_OUT | PX4IO_P_SETUP_FEATURES_SBUS2_OUT)) {
value &= ~(PX4IO_P_SETUP_FEATURES_PWM_RSSI | PX4IO_P_SETUP_FEATURES_ADC_RSSI);
}
#endif
/* disable the conflicting options with ADC RSSI */
if (value & (PX4IO_P_SETUP_FEATURES_ADC_RSSI)) {
value &= ~(PX4IO_P_SETUP_FEATURES_PWM_RSSI |
PX4IO_P_SETUP_FEATURES_SBUS1_OUT |
PX4IO_P_SETUP_FEATURES_SBUS2_OUT);
}
/* disable the conflicting options with PWM RSSI (without effect here, but for completeness) */
if (value & (PX4IO_P_SETUP_FEATURES_PWM_RSSI)) {
value &= ~(PX4IO_P_SETUP_FEATURES_ADC_RSSI |
PX4IO_P_SETUP_FEATURES_SBUS1_OUT |
PX4IO_P_SETUP_FEATURES_SBUS2_OUT);
}
/* apply changes */
r_setup_features = value;
break;
@@ -505,8 +550,7 @@ registers_set_one(uint8_t page, uint8_t offset, uint16_t value)
case PX4IO_P_SETUP_REBOOT_BL:
if ((r_status_flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) ||
(r_status_flags & PX4IO_P_STATUS_FLAGS_OVERRIDE) ||
(r_setup_arming & PX4IO_P_SETUP_ARMING_FMU_ARMED)) {
(r_status_flags & PX4IO_P_STATUS_FLAGS_OUTPUTS_ARMED)) {
// don't allow reboot while armed
break;
}
@@ -536,8 +580,7 @@ registers_set_one(uint8_t page, uint8_t offset, uint16_t value)
* do not allow a RC config change while outputs armed
*/
if ((r_status_flags & PX4IO_P_STATUS_FLAGS_SAFETY_OFF) ||
(r_status_flags & PX4IO_P_STATUS_FLAGS_OVERRIDE) ||
(r_setup_arming & PX4IO_P_SETUP_ARMING_FMU_ARMED)) {
(r_status_flags & PX4IO_P_STATUS_FLAGS_OUTPUTS_ARMED)) {
break;
}
src/modules/px4iofirmware/safety.c
+6 -3
View File
@@ -45,7 +45,6 @@
#include "px4io.h"
static struct hrt_call arming_call;
static struct hrt_call heartbeat_call;
static struct hrt_call failsafe_call;
/*
@@ -84,7 +83,11 @@ safety_init(void)
{
/* arrange for the button handler to be called at 10Hz */
hrt_call_every(&arming_call, 1000, 100000, safety_check_button, NULL);
}
void
failsafe_led_init(void)
{
/* arrange for the failsafe blinker to be called at 8Hz */
hrt_call_every(&failsafe_call, 1000, 125000, failsafe_blink, NULL);
}
@@ -165,8 +168,8 @@ failsafe_blink(void *arg)
/* indicate that a serious initialisation error occured */
if (!(r_status_flags & PX4IO_P_STATUS_FLAGS_INIT_OK)) {
LED_AMBER(true);
return;
}
return;
}
static bool failsafe = false;
src/modules/px4iofirmware/sbus.c
+36 -12
View File
@@ -1,6 +1,6 @@
/****************************************************************************
*
* Copyright (C) 2012 PX4 Development Team. All rights reserved.
* Copyright (c) 2012-2014 PX4 Development Team. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
@@ -87,7 +87,7 @@ static unsigned partial_frame_count;
unsigned sbus_frame_drops;
static bool sbus_decode(hrt_abstime frame_time, uint16_t *values, uint16_t *num_values, uint16_t *rssi, uint16_t max_channels);
static bool sbus_decode(hrt_abstime frame_time, uint16_t *values, uint16_t *num_values, bool *sbus_failsafe, bool *sbus_frame_drop, uint16_t max_channels);
int
sbus_init(const char *device)
@@ -118,7 +118,7 @@ sbus_init(const char *device)
}
bool
sbus_input(uint16_t *values, uint16_t *num_values, uint16_t *rssi, uint16_t max_channels)
sbus_input(uint16_t *values, uint16_t *num_values, bool *sbus_failsafe, bool *sbus_frame_drop, uint16_t max_channels)
{
ssize_t ret;
hrt_abstime now;
@@ -175,7 +175,7 @@ sbus_input(uint16_t *values, uint16_t *num_values, uint16_t *rssi, uint16_t max_
* decode it.
*/
partial_frame_count = 0;
return sbus_decode(now, values, num_values, rssi, max_channels);
return sbus_decode(now, values, num_values, sbus_failsafe, sbus_frame_drop, max_channels);
}
/*
@@ -215,14 +215,36 @@ static const struct sbus_bit_pick sbus_decoder[SBUS_INPUT_CHANNELS][3] = {
};
static bool
sbus_decode(hrt_abstime frame_time, uint16_t *values, uint16_t *num_values, uint16_t *rssi, uint16_t max_values)
sbus_decode(hrt_abstime frame_time, uint16_t *values, uint16_t *num_values, bool *sbus_failsafe, bool *sbus_frame_drop, uint16_t max_values)
{
/* check frame boundary markers to avoid out-of-sync cases */
if ((frame[0] != 0x0f) || (frame[24] != 0x00)) {
if ((frame[0] != 0x0f)) {
sbus_frame_drops++;
return false;
}
switch (frame[24]) {
case 0x00:
/* this is S.BUS 1 */
break;
case 0x03:
/* S.BUS 2 SLOT0: RX battery and external voltage */
break;
case 0x83:
/* S.BUS 2 SLOT1 */
break;
case 0x43:
case 0xC3:
case 0x23:
case 0xA3:
case 0x63:
case 0xE3:
break;
default:
/* we expect one of the bits above, but there are some we don't know yet */
break;
}
/* we have received something we think is a frame */
last_frame_time = frame_time;
@@ -267,20 +289,22 @@ sbus_decode(hrt_abstime frame_time, uint16_t *values, uint16_t *num_values, uint
/* decode and handle failsafe and frame-lost flags */
if (frame[SBUS_FLAGS_BYTE] & (1 << SBUS_FAILSAFE_BIT)) { /* failsafe */
/* report that we failed to read anything valid off the receiver */
*rssi = 0;
return false;
*sbus_failsafe = true;
*sbus_frame_drop = true;
}
else if (frame[SBUS_FLAGS_BYTE] & (1 << SBUS_FRAMELOST_BIT)) { /* a frame was lost */
/* set a special warning flag or try to calculate some kind of RSSI information - to be implemented
/* set a special warning flag
*
* Attention! This flag indicates a skipped frame only, not a total link loss! Handling this
* condition as fail-safe greatly reduces the reliability and range of the radio link,
* e.g. by prematurely issueing return-to-launch!!! */
*rssi = 100; // XXX magic number indicating bad signal, but not a signal loss (yet)
*sbus_failsafe = false;
*sbus_frame_drop = true;
} else {
*sbus_failsafe = false;
*sbus_frame_drop = false;
}
*rssi = 255;
return true;
}