drivers: rework NXP UWB driver (#21124)

* UWB driver rework that uses 2 UWB MKBoards - 1 as Controller (Initiator), one as Controllee (Anchor)

Co-authored-by: NXPBrianna <108274268+NXPBrianna@users.noreply.github.com>

msg/CMakeLists.txt

@@ -178,6 +178,7 @@ set(msg_files
 	SensorSelection.msg
 	SensorsStatus.msg
 	SensorsStatusImu.msg
+	SensorUwb.msg
 	SystemPower.msg
 	TakeoffStatus.msg
 	TaskStackInfo.msg
@@ -194,8 +195,6 @@ set(msg_files
 	UavcanParameterValue.msg
 	UlogStream.msg
 	UlogStreamAck.msg
-	UwbDistance.msg
-	UwbGrid.msg
 	VehicleAcceleration.msg
 	VehicleAirData.msg
 	VehicleAngularAccelerationSetpoint.msg

msg/SensorUwb.msg

@@ -0,0 +1,34 @@
+# UWB distance contains the distance information measured by an ultra-wideband positioning system,
+# such as Pozyx or NXP Rddrone.
+
+uint64 	timestamp		# time since system start (microseconds)
+
+uint32 	sessionid		# UWB SessionID
+uint32 	time_offset		# Time between Ranging Rounds in ms
+uint32 	counter			# Number of Ranges since last Start of Ranging
+uint16 	mac			# MAC adress of Initiator (controller)
+
+uint16 	mac_dest		# MAC adress of Responder (Controlee)
+uint16 	status			# status feedback #
+uint8 	nlos			# None line of site condition y/n
+float32 distance		# distance in m to the UWB receiver
+
+
+#Angle of arrival, Angle in Degree -60..+60; FOV in both axis is 120 degrees
+float32 aoa_azimuth_dev	# Angle of arrival of first incomming RX msg
+float32 aoa_elevation_dev	# Angle of arrival of first incomming RX msg
+float32 aoa_azimuth_resp	# Angle of arrival of first incomming RX msg at the responder
+float32 aoa_elevation_resp	# Angle of arrival of first incomming RX msg at the responder
+
+# Figure of merit for the angle measurements
+uint8 aoa_azimuth_fom		# AOA Azimuth FOM
+uint8 aoa_elevation_fom		# AOA Elevation FOM
+uint8 aoa_dest_azimuth_fom	# AOA Azimuth FOM
+uint8 aoa_dest_elevation_fom	# AOA Elevation FOM
+
+# Initiator physical configuration
+uint8 orientation		# Direction the sensor faces from MAV_SENSOR_ORIENTATION enum
+				# Standard configuration is Antennas facing down and azimuth aligened in forward direction
+float32 offset_x		# UWB initiator offset in X axis (NED drone frame)
+float32 offset_y		# UWB initiator offset in Y axis (NED drone frame)
+float32 offset_z		# UWB initiator offset in Z axis (NED drone frame)

msg/UwbDistance.msg

@@ -1,15 +0,0 @@
-# UWB distance contains the distance information measured by an ultra-wideband positioning system,
-# such as Pozyx or NXP Rddrone.
-
-uint64 	timestamp		# time since system start (microseconds)
-uint32 	time_uwb_ms		# Time of UWB device in ms
-uint32 	counter			# Number of Ranges since last Start of Ranging
-uint32 	sessionid		# UWB SessionID
-uint32 	time_offset		# Time between Ranging Rounds in ms
-uint16 	status			# status feedback #
-
-uint16[12] anchor_distance	# distance in cm to each UWB Anchor (UWB Device which takes part in Ranging)
-bool[12] nlos			# Visual line of sight yes/no
-float32[12] aoafirst		# Angle of arrival of first incoming RX msg
-
-float32[3] position		# Position of the Landing point in relation to the Drone (x,y,z in Meters NED)

msg/UwbGrid.msg

@@ -1,25 +0,0 @@
-# UWB report message contains the grid information measured by an ultra-wideband positioning system,
-# such as Pozyx or NXP Rddrone.
-
-uint64 	timestamp	# time since system start (microseconds)
-uint16 	initator_time	# time to synchronize clocks (microseconds)
-uint8 	num_anchors	# Number of anchors
-
-float64[4] target_gps	# GPS position of target of the UWB system (Lat / Lon / Alt / Yaw Offset to true North)
-
-# Grid position information
-# Position in x,y,z in  (x,y,z in centimeters NED)
-# staring with POI and Anchor 0 up to Anchor 11
-int16[3] target_pos 	# Point of Interest, mostly landing Target x,y,z
-int16[3] anchor_pos_0
-int16[3] anchor_pos_1
-int16[3] anchor_pos_2
-int16[3] anchor_pos_3
-int16[3] anchor_pos_4
-int16[3] anchor_pos_5
-int16[3] anchor_pos_6
-int16[3] anchor_pos_7
-int16[3] anchor_pos_8
-int16[3] anchor_pos_9
-int16[3] anchor_pos_10
-int16[3] anchor_pos_11