mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-11-04 10:01:36 +08:00
Intial Commit PX4 FMUV6RT
nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
This commit is contained in:
David Sidrane
committed by
Daniel Agar
Daniel Agar
parent
e3f8d53718
commit
e90e8ae0ea
@@ -0,0 +1,87 @@
|
||||
/************************************************************************************
|
||||
*
|
||||
* Copyright (C) 2016, 2018 Gregory Nutt. All rights reserved.
|
||||
* Authors: Gregory Nutt <gnutt@nuttx.org>
|
||||
* David Sidrane <david_s5@nscdg.com>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <px4_arch/spi_hw_description.h>
|
||||
#include <drivers/drv_sensor.h>
|
||||
#include <nuttx/spi/spi.h>
|
||||
|
||||
#include <px4_platform_common/px4_config.h>
|
||||
#include <px4_log.h>
|
||||
|
||||
#include <stdint.h>
|
||||
#include <stdbool.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/spi/spi.h>
|
||||
#include <arch/board/board.h>
|
||||
#include <systemlib/px4_macros.h>
|
||||
#include <px4_platform/gpio.h>
|
||||
|
||||
#include <arm_internal.h>
|
||||
#include <chip.h>
|
||||
#include "imxrt_lpspi.h"
|
||||
#include "imxrt_gpio.h"
|
||||
#include "board_config.h"
|
||||
#include <systemlib/err.h>
|
||||
|
||||
#ifdef CONFIG_IMXRT_LPSPI
|
||||
|
||||
|
||||
constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = {
|
||||
initSPIBus(SPI::Bus::LPSPI1, {
|
||||
initSPIDevice(DRV_IMU_DEVTYPE_ICM42688P, SPI::CS{GPIO::Port2, GPIO::Pin11}, SPI::DRDY{GPIO::Port3, GPIO::Pin19}), /* GPIO_EMC_B2_01 GPIO2_IO11, GPIO_AD_20, GPIO3_IO19 */
|
||||
}, {GPIO::Port2, GPIO::Pin1}), // Power GPIO_EMC_B1_33 GPIO2_IO01
|
||||
|
||||
initSPIBus(SPI::Bus::LPSPI2, {
|
||||
initSPIDevice(DRV_IMU_DEVTYPE_ICM42688P, SPI::CS{GPIO::Port3, GPIO::Pin24}, SPI::DRDY{GPIO::Port2, GPIO::Pin7}), /* GPIO_AD_25 GPIO3_IO24, GPIO_EMC_B1_39 GPIO2_IO07 */
|
||||
}, {GPIO::Port1, GPIO::Pin22}), // Power GPIO_EMC_B1_22 GPIO1_IO22
|
||||
|
||||
initSPIBus(SPI::Bus::LPSPI3, {
|
||||
initSPIDevice(DRV_GYR_DEVTYPE_BMI088, SPI::CS{GPIO::Port2, GPIO::Pin18}, SPI::DRDY{GPIO::Port2, GPIO::Pin28}), /* GPIO_EMC_B2_08 GPIO2_IO18, GPIO_EMC_B2_18 GPIO2_IO28 */
|
||||
initSPIDevice(DRV_ACC_DEVTYPE_BMI088, SPI::CS{GPIO::Port2, GPIO::Pin15}), /* GPIO_EMC_B2_05 GPIO2_IO15 */
|
||||
}, {GPIO::Port1, GPIO::Pin14}), // Power GPIO_EMC_B1_14 GPIO1_IO14
|
||||
|
||||
initSPIBusExternal(SPI::Bus::LPSPI6, {
|
||||
initSPIConfigExternal(SPI::CS{GPIO::Port6, GPIO::Pin9}, SPI::DRDY{GPIO::Port1, GPIO::Pin5}), /* GPIO_LPSR_09 GPIO6_IO09 GPIO_EMC_B1_05 GPIO1_IO05*/
|
||||
initSPIConfigExternal(SPI::CS{GPIO::Port6, GPIO::Pin8}, SPI::DRDY{GPIO::Port1, GPIO::Pin7}), /* GPIO_LPSR_08 GPIO6_IO08 GPIO_EMC_B1_07 GPIO1_IO07*/
|
||||
}),
|
||||
};
|
||||
|
||||
#endif
|
||||
static constexpr bool unused = validateSPIConfig(px4_spi_buses);
|
||||
Reference in New Issue
Block a user