mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-10-30 03:33:34 +08:00
Intial Commit PX4 FMUV6RT
nxp/rt117x:Fix Pin IRQ
nxp/rt117x:Support 4 i2c busses
nxp/rt117x:Add px4io_serial support
nxp/imxrt:Expand ToneAlarmInterface to GPT 3 & 4
px4_fmu-6xrt:Using imxrt_flexspi_nor_octal
px4_fmu-6xrt:Entry is start
px4_fmu-6xrt:Add Proper MTD
px4_fmu-6xrt:Set I2C Buses
px4_fmu-6xrt:Proper SPI usage
px4_fmu-6xrt:Adjust memory Map to use the 2 MB
px4_fmu-6xrt:Bring in ROMAPI
px4_fmu-6xrt:Push FLASH to 200Mhz
px4_fmu-6xrt:Use BOARD_I2C_LATEINIT
px4_fmu-6xrt:Clock Config remove unused devices
px4_fmu-6xrt:Remove EVK SDRAM IO
px4_fmu-6xrt:Enable SE550 using HW_VER_REV_DRIVE
px4_fmu-6xrt:Use MTD to mount FRAM on Flex SPI
px4_fmu-6xrt:Manifest
px4_fmu-6xrt:Restore board_peripheral_reset
px4_fmu-6xrt:Set I2C buss Interna/Externa and startup
nxp/rt117x:Set 6 I2C busses
px4_fmu-6xrt:Correct Clock Sources and Freqency Settings
px4_fmu-6xrt:Correct ADC Settings
px4_fmu-6xrt:Tune FlexSPI config and sync header with debug variant Linker prep for rodata ahb partitioning
px4_fmu-6xrt:FlexSPI prefetch partition split .text and .rodata
Current config
1KB Prefetch .rodata
3KB Prefetch .text
px4_fmu-6xrt:Run imxrt_flash_setup_prefetch_partition from ram with barriers
px4_fmu-6xrt:Use All OCTL setting from FLASH g_flash_config SANS lookupTable
px4_fmu-6xrt:Octal spi boot/debug problem bypass
px4_fmu-6xrt:Add PWM test
px4_fmu-6xrt:Fix clockconfig and USB vbus sense
px4_fmu-6xrt: Use TCM
px4_fmu-6xrt: Ethernet bringup
imxrt: use unique_id register for board_identity
px4_fmu-6xrt: update ITCM mapping, todo proper trap on pc hitting 0x0
px4_fmu-6xrt:correct rotation icm42688p onboard imu
rt117x: Add SSARC HP RAM driver for memory dumps
px4_fmu-6xrt: Enable hardfault_log
px4_fmu-6xrt: Enable DMA pool
px4_fmu-6xrt: fix uart mapping
px4_fmu-6xrt: enable SocketCAN & DroneCAN
px4_fmu-6xrt:Command line history TAB completion
px4_fmu-6xrt:Fix pinning duplication
px4_fmu-6xrt:Support conditional PHY address based on selected PHY
px4_fmu-6xrt:Add Pull Downs on CTS, use GPIO for RTS
px4_fmu-6xrt:Set TelemN TX Slew rate and Drive Strenth to max
px4_fmu-6xrt::Set TELEM Buffers add HW HS
px4_fmu-6xrt:Turn off DMA poll
px4_fmu-6xrt:RC_SERIAL_PORT needed to be px4io to disable rc_input using TELEM2!
px4_fmu-6xrt: bootloader (#22228)
* imxrt:Add bootloader support
* bootloader:imxrt clear BOOT_RTC_SIGNATURE
* px4_fmu-6xrt:Add bootloader
* px4_fmu-6xrt:bootloader removed ADC
* px4_fmu-6xrt:bootloader base bootloader script off of script.ld
* px4_fmu-6xrt:add _bootdelay_signature & change entry from 0x30000000 to 0x30040000
* px4_fmu-6xrt:hw_config Bootloader has to have 12 bytes
px4_fmu-6xrt:Default to use LAN8742A PHY
px4_fmu-v6xrt:VID Set to Drone Code
board_reset:Enable ability to write RTC GP regs
px4_fmu-6xrt:Fix CMP0079 error
rt117x:micro_hal Add a PX4_MAKE_GPIO_PULLED_INPUT
px4_fmu-v6xrt:Set CTS High before VDD_5V applided to ports to avoid radios fro entering bootloaders
fmu-v6xrt: increase 5v down time
fmu-v6xrt:Ready for Release DEBUGASSERTS off and Console 57600,
Bootloder updated.
imxrt:board_hw_rev_ver Rework for 3.893V Ref
px4_fmu-v6xrt:Move ADC to Port3
This commit is contained in:
David Sidrane
committed by
Daniel Agar
Daniel Agar
parent
e3f8d53718
commit
e90e8ae0ea
@@ -0,0 +1,133 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (C) 2022 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/spi/spi.h>
|
||||
#include <px4_platform_common/px4_manifest.h>
|
||||
|
||||
static const px4_mft_device_t qspi_flash = { // FM25V02A on FMUM 32K 512 X 64
|
||||
.bus_type = px4_mft_device_t::FLEXSPI, // Using Flex SPI
|
||||
};
|
||||
// KiB BS nB
|
||||
static const px4_mft_device_t i2c3 = { // 24LC64T on IMU 8K 32 X 256
|
||||
.bus_type = px4_mft_device_t::I2C,
|
||||
.devid = PX4_MK_I2C_DEVID(3, 0x50)
|
||||
};
|
||||
static const px4_mft_device_t i2c6 = { // 24LC64T on BASE 8K 32 X 256
|
||||
.bus_type = px4_mft_device_t::I2C,
|
||||
.devid = PX4_MK_I2C_DEVID(6, 0x51)
|
||||
};
|
||||
|
||||
|
||||
static const px4_mtd_entry_t fmum_fram = {
|
||||
.device = &qspi_flash,
|
||||
.npart = 2,
|
||||
.partd = {
|
||||
{
|
||||
.type = MTD_PARAMETERS,
|
||||
.path = "/fs/mtd_params",
|
||||
.nblocks = 32
|
||||
},
|
||||
{
|
||||
.type = MTD_WAYPOINTS,
|
||||
.path = "/fs/mtd_waypoints",
|
||||
.nblocks = 32
|
||||
|
||||
}
|
||||
},
|
||||
};
|
||||
|
||||
static const px4_mtd_entry_t base_eeprom = {
|
||||
.device = &i2c6,
|
||||
.npart = 2,
|
||||
.partd = {
|
||||
{
|
||||
.type = MTD_MFT_VER,
|
||||
.path = "/fs/mtd_mft_ver",
|
||||
.nblocks = 248
|
||||
},
|
||||
{
|
||||
.type = MTD_NET,
|
||||
.path = "/fs/mtd_net",
|
||||
.nblocks = 8 // 256 = 32 * 8
|
||||
|
||||
}
|
||||
},
|
||||
};
|
||||
|
||||
static const px4_mtd_entry_t imu_eeprom = {
|
||||
.device = &i2c3,
|
||||
.npart = 3,
|
||||
.partd = {
|
||||
{
|
||||
.type = MTD_CALDATA,
|
||||
.path = "/fs/mtd_caldata",
|
||||
.nblocks = 240
|
||||
},
|
||||
{
|
||||
.type = MTD_MFT_REV,
|
||||
.path = "/fs/mtd_mft_rev",
|
||||
.nblocks = 8
|
||||
},
|
||||
{
|
||||
.type = MTD_ID,
|
||||
.path = "/fs/mtd_id",
|
||||
.nblocks = 8 // 256 = 32 * 8
|
||||
}
|
||||
},
|
||||
};
|
||||
|
||||
static const px4_mtd_manifest_t board_mtd_config = {
|
||||
.nconfigs = 3,
|
||||
.entries = {
|
||||
&fmum_fram,
|
||||
&base_eeprom,
|
||||
&imu_eeprom
|
||||
}
|
||||
};
|
||||
|
||||
static const px4_mft_entry_s mtd_mft = {
|
||||
.type = MTD,
|
||||
.pmft = (void *) &board_mtd_config,
|
||||
};
|
||||
|
||||
static const px4_mft_s mft = {
|
||||
.nmft = 1,
|
||||
.mfts = {
|
||||
&mtd_mft
|
||||
}
|
||||
};
|
||||
|
||||
const px4_mft_s *board_get_manifest(void)
|
||||
{
|
||||
return &mft;
|
||||
}
|
||||
Reference in New Issue
Block a user