Add Gumstix AeroCore device

Based on the work of Andrew Smith [1], add board configuration and device
drivers to support the Gumstix AeroCore (previously Aerodroid) board [2]. The
AeroCore is an autopilot board based on a STM32F427 similar to the FMUv2.

[1] https://github.com/smithandrewc/Firmware
[2] https://store.gumstix.com/index.php/products/585/

Signed-off-by: Ash Charles <ashcharles@gmail.com>

src/drivers/boards/aerocore/aerocore_init.c

@@ -0,0 +1,282 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file aerocore_init.c
+ *
+ * AeroCore-specific early startup code.  This file implements the
+ * nsh_archinitialize() function that is called early by nsh during startup.
+ *
+ * Code here is run before the rcS script is invoked; it should start required
+ * subsystems and perform board-specific initialisation.
+ */
+
+/****************************************************************************
+ * Included Files
+ ****************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdbool.h>
+#include <stdio.h>
+#include <debug.h>
+#include <errno.h>
+
+#include <nuttx/arch.h>
+#include <nuttx/spi.h>
+#include <nuttx/i2c.h>
+#include <nuttx/mmcsd.h>
+#include <nuttx/analog/adc.h>
+#include <nuttx/gran.h>
+
+#include <stm32.h>
+#include "board_config.h"
+#include <stm32_uart.h>
+
+#include <arch/board/board.h>
+
+#include <drivers/drv_hrt.h>
+#include <drivers/drv_led.h>
+
+#include <systemlib/cpuload.h>
+#include <systemlib/perf_counter.h>
+
+/****************************************************************************
+ * Pre-Processor Definitions
+ ****************************************************************************/
+
+/* Configuration ************************************************************/
+
+/* Debug ********************************************************************/
+
+#ifdef CONFIG_CPP_HAVE_VARARGS
+#  ifdef CONFIG_DEBUG
+#    define message(...) lowsyslog(__VA_ARGS__)
+#  else
+#    define message(...) printf(__VA_ARGS__)
+#  endif
+#else
+#  ifdef CONFIG_DEBUG
+#    define message lowsyslog
+#  else
+#    define message printf
+#  endif
+#endif
+
+/****************************************************************************
+ * Protected Functions
+ ****************************************************************************/
+
+#if defined(CONFIG_FAT_DMAMEMORY)
+# if !defined(CONFIG_GRAN) || !defined(CONFIG_FAT_DMAMEMORY)
+#  error microSD DMA support requires CONFIG_GRAN
+# endif
+
+static GRAN_HANDLE dma_allocator;
+
+/* 
+ * The DMA heap size constrains the total number of things that can be 
+ * ready to do DMA at a time.
+ *
+ * For example, FAT DMA depends on one sector-sized buffer per filesystem plus
+ * one sector-sized buffer per file. 
+ *
+ * We use a fundamental alignment / granule size of 64B; this is sufficient
+ * to guarantee alignment for the largest STM32 DMA burst (16 beats x 32bits).
+ */
+static uint8_t g_dma_heap[8192] __attribute__((aligned(64)));
+static perf_counter_t g_dma_perf;
+
+static void
+dma_alloc_init(void)
+{
+	dma_allocator = gran_initialize(g_dma_heap,
+					sizeof(g_dma_heap),
+					7,  /* 128B granule - must be > alignment (XXX bug?) */
+					6); /* 64B alignment */
+	if (dma_allocator == NULL) {
+		message("[boot] DMA allocator setup FAILED");
+	} else {
+		g_dma_perf = perf_alloc(PC_COUNT, "DMA allocations");
+	}
+}
+
+/****************************************************************************
+ * Public Functions
+ ****************************************************************************/
+
+/*
+ * DMA-aware allocator stubs for the FAT filesystem.
+ */
+
+__EXPORT void *fat_dma_alloc(size_t size);
+__EXPORT void fat_dma_free(FAR void *memory, size_t size);
+
+void *
+fat_dma_alloc(size_t size)
+{
+	perf_count(g_dma_perf);
+	return gran_alloc(dma_allocator, size);
+}
+
+void
+fat_dma_free(FAR void *memory, size_t size)
+{
+	gran_free(dma_allocator, memory, size);
+}
+
+#else
+
+# define dma_alloc_init()
+
+#endif
+
+/************************************************************************************
+ * Name: stm32_boardinitialize
+ *
+ * Description:
+ *   All STM32 architectures must provide the following entry point.  This entry point
+ *   is called early in the intitialization -- after all memory has been configured
+ *   and mapped but before any devices have been initialized.
+ *
+ ************************************************************************************/
+
+__EXPORT void
+stm32_boardinitialize(void)
+{
+	/* configure SPI interfaces */
+	stm32_spiinitialize();
+
+	/* configure LEDs */
+	up_ledinit();
+}
+
+/****************************************************************************
+ * Name: nsh_archinitialize
+ *
+ * Description:
+ *   Perform architecture specific initialization
+ *
+ ****************************************************************************/
+
+static struct spi_dev_s *spi3;
+static struct spi_dev_s *spi4;
+
+#include <math.h>
+
+#ifdef __cplusplus
+__EXPORT int matherr(struct __exception *e)
+{
+	return 1;
+}
+#else
+__EXPORT int matherr(struct exception *e)
+{
+	return 1;
+}
+#endif
+
+__EXPORT int nsh_archinitialize(void)
+{
+
+	/* configure ADC pins */
+	stm32_configgpio(GPIO_ADC1_IN10);	/* used by VBUS valid */
+	stm32_configgpio(GPIO_ADC1_IN11);	/* J1 breakout */
+	stm32_configgpio(GPIO_ADC1_IN12);	/* J1 breakout */
+	stm32_configgpio(GPIO_ADC1_IN13);	/* J1 breakout */
+
+	/* configure the high-resolution time/callout interface */
+	hrt_init();
+
+	/* configure the DMA allocator */
+	dma_alloc_init();
+
+	/* configure CPU load estimation */
+#ifdef CONFIG_SCHED_INSTRUMENTATION
+	cpuload_initialize_once();
+#endif
+
+	/* set up the serial DMA polling */
+	static struct hrt_call serial_dma_call;
+	struct timespec ts;
+
+	/*
+	 * Poll at 1ms intervals for received bytes that have not triggered
+	 * a DMA event.
+	 */
+	ts.tv_sec = 0;
+	ts.tv_nsec = 1000000;
+
+	hrt_call_every(&serial_dma_call,
+		       ts_to_abstime(&ts),
+		       ts_to_abstime(&ts),
+		       (hrt_callout)stm32_serial_dma_poll,
+		       NULL);
+
+	/* initial LED state */
+	drv_led_start();
+	led_off(LED_AMBER);
+
+	/* Configure Sensors on SPI bus #3 */
+	spi3 = up_spiinitialize(3);
+	if (!spi3) {
+		message("[boot] FAILED to initialize SPI port 3\n");
+		up_ledon(LED_AMBER);
+		return -ENODEV;
+	}
+	/* Default: 1MHz, 8 bits, Mode 3 */
+	SPI_SETFREQUENCY(spi3, 10000000);
+	SPI_SETBITS(spi3, 8);
+	SPI_SETMODE(spi3, SPIDEV_MODE3);
+	SPI_SELECT(spi3, PX4_SPIDEV_GYRO, false);
+	SPI_SELECT(spi3, PX4_SPIDEV_ACCEL_MAG, false);
+	SPI_SELECT(spi3, PX4_SPIDEV_BARO, false);
+	up_udelay(20);
+	message("[boot] Initialized SPI port 3 (SENSORS)\n");
+
+	/* Configure FRAM on SPI bus #4 */
+	spi4 = up_spiinitialize(4);
+	if (!spi4) {
+		message("[boot] FAILED to initialize SPI port 4\n");
+		up_ledon(LED_AMBER);
+		return -ENODEV;
+	}
+	/* Default: ~10MHz, 8 bits, Mode 3 */
+	SPI_SETFREQUENCY(spi4, 10 * 1000 * 1000);
+	SPI_SETBITS(spi4, 8);
+	SPI_SETMODE(spi4, SPIDEV_MODE0);
+	SPI_SELECT(spi4, SPIDEV_FLASH, false);
+	message("[boot] Initialized SPI port 4 (FRAM)\n");
+
+	return OK;
+}

src/drivers/boards/aerocore/aerocore_led.c

@@ -0,0 +1,121 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2013 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file aerocore_led.c
+ *
+ * AeroCore LED backend.
+ */
+
+#include <nuttx/config.h>
+
+#include <stdbool.h>
+
+#include "stm32.h"
+#include "board_config.h"
+
+#include <arch/board/board.h>
+
+/*
+ * Ideally we'd be able to get these from up_internal.h,
+ * but since we want to be able to disable the NuttX use
+ * of leds for system indication at will and there is no
+ * separate switch, we need to build independent of the
+ * CONFIG_ARCH_LEDS configuration switch.
+ */
+__BEGIN_DECLS
+extern void led_init();
+extern void led_on(int led);
+extern void led_off(int led);
+extern void led_toggle(int led);
+__END_DECLS
+
+__EXPORT void led_init()
+{
+	stm32_configgpio(GPIO_LED0);
+	stm32_configgpio(GPIO_LED1);
+}
+
+__EXPORT void led_on(int led)
+{
+	switch (led) {
+	case 0:
+		stm32_gpiowrite(GPIO_LED0, true);
+		break;
+
+	case 1:
+		stm32_gpiowrite(GPIO_LED1, true);
+		break;
+
+	default:
+		warnx("LED ID not recognized\n");
+	}
+}
+
+__EXPORT void led_off(int led)
+{
+	switch (led) {
+	case 0:
+		stm32_gpiowrite(GPIO_LED0, false);
+		break;
+
+	case 1:
+		stm32_gpiowrite(GPIO_LED1, false);
+		break;
+
+	default:
+		warnx("LED ID not recognized\n");
+	}
+}
+
+__EXPORT void led_toggle(int led)
+{
+	switch (led) {
+	case 0:
+		if (stm32_gpioread(GPIO_LED0))
+			stm32_gpiowrite(GPIO_LED0, false);
+		else
+			stm32_gpiowrite(GPIO_LED0, true);
+		break;
+
+	case 1:
+		if (stm32_gpioread(GPIO_LED1))
+			stm32_gpiowrite(GPIO_LED1, false);
+		else
+			stm32_gpiowrite(GPIO_LED1, true);
+		break;
+
+	default:
+		warnx("LED ID not recognized\n");
+	}
+}

src/drivers/boards/aerocore/aerocore_pwm_servo.c

@@ -0,0 +1,117 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/*
+ * @file aerocore_pwm_servo.c
+ *
+ * Configuration data for the stm32 pwm_servo driver.
+ *
+ * Note that these arrays must always be fully-sized.
+ */
+
+#include <stdint.h>
+
+#include <stm32.h>
+#include <stm32_gpio.h>
+#include <stm32_tim.h>
+
+#include <drivers/stm32/drv_pwm_servo.h>
+#include <drivers/drv_pwm_output.h>
+
+#include "board_config.h"
+
+__EXPORT const struct pwm_servo_timer pwm_timers[PWM_SERVO_MAX_TIMERS] = {
+	{
+		.base = STM32_TIM1_BASE,
+		.clock_register = STM32_RCC_APB2ENR,
+		.clock_bit = RCC_APB2ENR_TIM1EN,
+		.clock_freq = STM32_APB2_TIM1_CLKIN
+	},
+	{
+		.base = STM32_TIM3_BASE,
+		.clock_register = STM32_RCC_APB1ENR,
+		.clock_bit = RCC_APB1ENR_TIM3EN,
+		.clock_freq = STM32_APB1_TIM3_CLKIN
+	}
+};
+
+__EXPORT const struct pwm_servo_channel pwm_channels[PWM_SERVO_MAX_CHANNELS] = {
+	{
+		.gpio = GPIO_TIM1_CH1OUT,
+		.timer_index = 0,
+		.timer_channel = 1,
+		.default_value = 1500,
+	},
+	{
+		.gpio = GPIO_TIM1_CH2OUT,
+		.timer_index = 0,
+		.timer_channel = 2,
+		.default_value = 1500,
+	},
+	{
+		.gpio = GPIO_TIM1_CH3OUT,
+		.timer_index = 0,
+		.timer_channel = 3,
+		.default_value = 1500,
+	},
+	{
+		.gpio = GPIO_TIM1_CH4OUT,
+		.timer_index = 0,
+		.timer_channel = 4,
+		.default_value = 1500,
+	},
+	{
+		.gpio = GPIO_TIM3_CH1OUT,
+		.timer_index = 1,
+		.timer_channel = 1,
+		.default_value = 1500,
+	},
+	{
+		.gpio = GPIO_TIM3_CH2OUT,
+		.timer_index = 1,
+		.timer_channel = 2,
+		.default_value = 1500,
+	},
+	{
+		.gpio = GPIO_TIM3_CH3OUT,
+		.timer_index = 1,
+		.timer_channel = 3,
+		.default_value = 1500,
+	},
+	{
+		.gpio = GPIO_TIM3_CH4OUT,
+		.timer_index = 1,
+		.timer_channel = 4,
+		.default_value = 1500,
+	}
+};

src/drivers/boards/aerocore/aerocore_spi.c

@@ -0,0 +1,183 @@
+/****************************************************************************
+ *
+ *   Copyright (C) 2012 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file aerocore_spi.c
+ *
+ * Board-specific SPI functions.
+ */
+
+/************************************************************************************
+ * Included Files
+ ************************************************************************************/
+
+#include <nuttx/config.h>
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <debug.h>
+
+#include <nuttx/spi.h>
+#include <arch/board/board.h>
+
+#include <up_arch.h>
+#include <chip.h>
+#include <stm32.h>
+#include "board_config.h"
+
+/************************************************************************************
+ * Public Functions
+ ************************************************************************************/
+
+/************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the PX4FMU board.
+ *
+ ************************************************************************************/
+
+__EXPORT void weak_function stm32_spiinitialize(void)
+{
+#ifdef CONFIG_STM32_SPI1
+	stm32_configgpio(GPIO_SPI1_NSS);
+	stm32_gpiowrite(GPIO_SPI1_NSS, 1);
+#endif
+
+#ifdef CONFIG_STM32_SPI2
+	stm32_configgpio(GPIO_SPI2_NSS);
+	stm32_gpiowrite(GPIO_SPI2_NSS, 1);
+#endif
+
+#ifdef CONFIG_STM32_SPI3
+	stm32_configgpio(GPIO_SPI_CS_GYRO);
+	stm32_configgpio(GPIO_SPI_CS_ACCEL_MAG);
+	stm32_configgpio(GPIO_SPI_CS_BARO);
+
+	/* De-activate all peripherals,
+	 * required for some peripheral
+	 * state machines
+	 */
+	stm32_gpiowrite(GPIO_SPI_CS_GYRO, 1);
+	stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG, 1);
+	stm32_gpiowrite(GPIO_SPI_CS_BARO, 1);
+
+	stm32_configgpio(GPIO_EXTI_GYRO_DRDY);
+	stm32_configgpio(GPIO_EXTI_MAG_DRDY);
+	stm32_configgpio(GPIO_EXTI_ACCEL_DRDY);
+#endif
+
+#ifdef CONFIG_STM32_SPI4
+	stm32_configgpio(GPIO_SPI4_NSS);
+	stm32_gpiowrite(GPIO_SPI4_NSS, 1);
+#endif
+}
+
+#ifdef CONFIG_STM32_SPI1
+__EXPORT void stm32_spi1select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+	/* there is only one device broken-out so select it */
+	stm32_gpiowrite(GPIO_SPI1_NSS, !selected);
+}
+
+__EXPORT uint8_t stm32_spi1status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+	return SPI_STATUS_PRESENT;
+}
+#endif
+
+#ifdef CONFIG_STM32_SPI2
+__EXPORT void stm32_spi2select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+	/* there is only one device broken-out so select it */
+	stm32_gpiowrite(GPIO_SPI2_NSS, !selected);
+}
+
+__EXPORT uint8_t stm32_spi2status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+	return SPI_STATUS_PRESENT;
+}
+#endif
+
+#ifdef CONFIG_STM32_SPI3
+__EXPORT void stm32_spi3select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+	/* SPI select is active low, so write !selected to select the device */
+
+	switch (devid) {
+	case PX4_SPIDEV_GYRO:
+		/* Making sure the other peripherals are not selected */
+		stm32_gpiowrite(GPIO_SPI_CS_GYRO, !selected);
+		stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG, 1);
+		stm32_gpiowrite(GPIO_SPI_CS_BARO, 1);
+		break;
+
+	case PX4_SPIDEV_ACCEL_MAG:
+		/* Making sure the other peripherals are not selected */
+		stm32_gpiowrite(GPIO_SPI_CS_GYRO, 1);
+		stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG, !selected);
+		stm32_gpiowrite(GPIO_SPI_CS_BARO, 1);
+		break;
+
+	case PX4_SPIDEV_BARO:
+		/* Making sure the other peripherals are not selected */
+		stm32_gpiowrite(GPIO_SPI_CS_GYRO, 1);
+		stm32_gpiowrite(GPIO_SPI_CS_ACCEL_MAG, 1);
+		stm32_gpiowrite(GPIO_SPI_CS_BARO, !selected);
+		break;
+
+	default:
+		break;
+	}
+}
+
+__EXPORT uint8_t stm32_spi3status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+	return SPI_STATUS_PRESENT;
+}
+#endif
+
+
+#ifdef CONFIG_STM32_SPI4
+__EXPORT void stm32_spi4select(FAR struct spi_dev_s *dev, enum spi_dev_e devid, bool selected)
+{
+	/* there can only be one device on this bus, so always select it */
+	stm32_gpiowrite(GPIO_SPI4_NSS, !selected);
+}
+
+__EXPORT uint8_t stm32_spi4status(FAR struct spi_dev_s *dev, enum spi_dev_e devid)
+{
+	/* FRAM is always present */
+	return SPI_STATUS_PRESENT;
+}
+#endif

src/drivers/boards/aerocore/board_config.h

@@ -0,0 +1,176 @@
+/****************************************************************************
+ *
+ *   Copyright (c) 2013, 2014 PX4 Development Team. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ * 3. Neither the name PX4 nor the names of its contributors may be
+ *    used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ ****************************************************************************/
+
+/**
+ * @file board_config.h
+ *
+ * AeroCore internal definitions
+ */
+
+#pragma once
+
+/****************************************************************************************************
+ * Included Files
+ ****************************************************************************************************/
+
+#include <nuttx/config.h>
+#include <nuttx/compiler.h>
+#include <stdint.h>
+
+__BEGIN_DECLS
+
+/* these headers are not C++ safe */
+#include <stm32.h>
+#include <arch/board/board.h>
+
+#define UDID_START		0x1FFF7A10
+ 
+/****************************************************************************************************
+ * Definitions
+ ****************************************************************************************************/
+
+/* LEDs */
+#define GPIO_LED0	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN9)
+#define GPIO_LED1	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN10)
+
+/* Gyro */
+#define GPIO_EXTI_GYRO_DRDY	(GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTD|GPIO_PIN0)
+
+/* Accel & Mag */
+#define GPIO_EXTI_MAG_DRDY	(GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTD|GPIO_PIN1)
+#define GPIO_EXTI_ACCEL_DRDY	(GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTD|GPIO_PIN2)
+
+/* GPS */
+#define GPIO_GPS_NRESET		(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN5)
+#define GPIO_GPS_TIMEPULSE	(GPIO_INPUT|GPIO_FLOAT|GPIO_PORTC|GPIO_PIN4)
+
+/* SPI3--Sensors */
+#define PX4_SPI_BUS_SENSORS	3
+#define GPIO_SPI_CS_ACCEL_MAG	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN2)
+#define GPIO_SPI_CS_GYRO	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3)
+#define GPIO_SPI_CS_BARO	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN4)
+
+/* Nominal chip selects for devices on SPI bus #3 */
+#define PX4_SPIDEV_ACCEL_MAG	0
+#define PX4_SPIDEV_GYRO		1
+#define PX4_SPIDEV_BARO		2
+
+/* User GPIOs broken out on J11 */
+#define GPIO_GPIO0_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN0)
+#define GPIO_GPIO1_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN1)
+//#define GPIO_GPIO2_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN0)
+#define GPIO_GPIO3_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN1)
+#define GPIO_GPIO4_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN2)
+#define GPIO_GPIO5_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTA|GPIO_PIN3)
+#define GPIO_GPIO6_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTD|GPIO_PIN12)
+#define GPIO_GPIO7_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTD|GPIO_PIN13)
+#define GPIO_GPIO8_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTD|GPIO_PIN14)
+#define GPIO_GPIO9_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTD|GPIO_PIN15)
+#define GPIO_GPIO10_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN5)
+#define GPIO_GPIO11_INPUT	(GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN8)
+
+#define GPIO_GPIO0_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN0)
+#define GPIO_GPIO1_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN1)
+//#define GPIO_GPIO2_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN0)
+#define GPIO_GPIO3_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN1)
+#define GPIO_GPIO4_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN2)
+#define GPIO_GPIO5_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN3)
+#define GPIO_GPIO6_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN12)
+#define GPIO_GPIO7_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN13)
+#define GPIO_GPIO8_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN14)
+#define GPIO_GPIO9_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTD|GPIO_PIN15)
+#define GPIO_GPIO10_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN5)
+#define GPIO_GPIO11_OUTPUT	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN8)
+
+/* PWM
+ *
+ * Eight PWM outputs are configured.
+ *
+ * Pins:
+ *
+ * CH1 : PA8  : TIM1_CH1
+ * CH2 : PA9  : TIM1_CH2
+ * CH3 : PA10 : TIM1_CH3
+ * CH4 : PA11 : TIM1_CH4
+ * CH5 : PC6  : TIM3_CH1
+ * CH6 : PC7  : TIM3_CH2
+ * CH7 : PC8  : TIM3_CH3
+ * CH8 : PC9  : TIM3_CH4
+ */
+#define GPIO_TIM1_CH1OUT	GPIO_TIM1_CH1OUT_1
+#define GPIO_TIM1_CH2OUT	GPIO_TIM1_CH2OUT_1
+#define GPIO_TIM1_CH3OUT	GPIO_TIM1_CH3OUT_1
+#define GPIO_TIM1_CH4OUT	GPIO_TIM1_CH4OUT_1
+#define GPIO_TIM3_CH1OUT	GPIO_TIM3_CH1OUT_3
+#define GPIO_TIM3_CH2OUT	GPIO_TIM3_CH2OUT_3
+#define GPIO_TIM3_CH3OUT	GPIO_TIM3_CH3OUT_2
+#define GPIO_TIM3_CH4OUT	GPIO_TIM3_CH4OUT_2
+
+/* High-resolution timer */
+#define HRT_TIMER		8	/* use timer 8 for the HRT */
+#define HRT_TIMER_CHANNEL	1	/* use capture/compare channel */
+
+/* Tone Alarm (no onboard speaker )*/
+#define TONE_ALARM_TIMER	2	/* timer 2 */
+#define TONE_ALARM_CHANNEL	1	/* channel 1 */
+#define GPIO_TONE_ALARM_IDLE	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN0)
+#define GPIO_TONE_ALARM		(GPIO_ALT|GPIO_AF1|GPIO_SPEED_2MHz|GPIO_PUSHPULL|GPIO_PORTA|GPIO_PIN0)
+
+
+/****************************************************************************************************
+ * Public Types
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Public data
+ ****************************************************************************************************/
+
+#ifndef __ASSEMBLY__
+
+/****************************************************************************************************
+ * Public Functions
+ ****************************************************************************************************/
+
+/****************************************************************************************************
+ * Name: stm32_spiinitialize
+ *
+ * Description:
+ *   Called to configure SPI chip select GPIO pins for the PX4FMU board.
+ *
+ ****************************************************************************************************/
+
+extern void stm32_spiinitialize(void);
+
+#endif /* __ASSEMBLY__ */
+
+__END_DECLS

src/drivers/boards/aerocore/module.mk

@@ -0,0 +1,8 @@
+#
+# Board-specific startup code for the AeroCore
+#
+
+SRCS		 = aerocore_init.c \
+		   aerocore_pwm_servo.c \
+		   aerocore_spi.c \
+		   aerocore_led.c

src/drivers/boards/px4fmu-v1/board_config.h

@@ -85,6 +85,8 @@ __BEGIN_DECLS
 #define GPIO_SPI_CS_MPU		(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN0)
 #define GPIO_SPI_CS_SDCARD	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
 
+#define PX4_SPI_BUS_SENSORS	1
+
 /*
  * Use these in place of the spi_dev_e enumeration to
  * select a specific SPI device on SPI1

src/drivers/boards/px4fmu-v2/board_config.h

@@ -107,6 +107,8 @@ __BEGIN_DECLS
 #define GPIO_SPI_CS_FRAM	(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN10)
 #define GPIO_SPI_CS_MPU		(GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN2)
 
+#define PX4_SPI_BUS_SENSORS	1
+
 /* Use these in place of the spi_dev_e enumeration to select a specific SPI device on SPI1 */
 #define PX4_SPIDEV_GYRO		1
 #define PX4_SPIDEV_ACCEL_MAG	2

src/drivers/drv_gpio.h

@@ -94,6 +94,14 @@
 
 #endif
 
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+/*
+ * AeroCore GPIO numbers and configuration.
+ *
+ */
+# define PX4FMU_DEVICE_PATH	"/dev/px4fmu"
+#endif
+
 #ifdef CONFIG_ARCH_BOARD_PX4IO_V1
 /* no GPIO driver on the PX4IOv1 board */
 #endif
@@ -146,4 +154,4 @@
 
 #define GPIO_SENSOR_RAIL_RESET	GPIOC(13)
 
-#endif /* _DRV_GPIO_H */
+#endif /* _DRV_GPIO_H */

src/drivers/drv_gps.h

@@ -46,7 +46,11 @@
 #include "drv_sensor.h"
 #include "drv_orb_dev.h"
 
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+#define GPS_DEFAULT_UART_PORT "/dev/ttyS0"
+#else
 #define GPS_DEFAULT_UART_PORT "/dev/ttyS3"
+#endif
 
 #define GPS_DEVICE_PATH	"/dev/gps"
 

src/drivers/gps/gps.cpp

@@ -63,6 +63,8 @@
 #include <uORB/uORB.h>
 #include <uORB/topics/vehicle_gps_position.h>
 
+#include <board_config.h>
+
 #include "ubx.h"
 #include "mtk.h"
 
@@ -421,7 +423,14 @@ GPS::task_main()
 void
 GPS::cmd_reset()
 {
-	//XXX add reset?
+#ifdef GPIO_GPS_NRESET
+	warnx("Toggling GPS reset pin");
+	stm32_configgpio(GPIO_GPS_NRESET);
+	stm32_gpiowrite(GPIO_GPS_NRESET, 0);
+	usleep(100);
+	stm32_gpiowrite(GPIO_GPS_NRESET, 1);
+	warnx("Toggled GPS reset pin");
+#endif
 }
 
 void

src/drivers/lsm303d/lsm303d.cpp

@@ -1793,7 +1793,7 @@ start()
 		errx(0, "already started");
 
 	/* create the driver */
-	g_dev = new LSM303D(1 /* SPI dev 1 */, LSM303D_DEVICE_PATH_ACCEL, (spi_dev_e)PX4_SPIDEV_ACCEL_MAG);
+	g_dev = new LSM303D(PX4_SPI_BUS_SENSORS, LSM303D_DEVICE_PATH_ACCEL, (spi_dev_e)PX4_SPIDEV_ACCEL_MAG);
 
 	if (g_dev == nullptr) {
 		warnx("failed instantiating LSM303D obj");

src/drivers/ms5611/ms5611_spi.cpp

@@ -117,7 +117,7 @@ private:
 device::Device *
 MS5611_spi_interface(ms5611::prom_u &prom_buf)
 {
-	return new MS5611_SPI(1 /* XXX MAGIC NUMBER */, (spi_dev_e)PX4_SPIDEV_BARO, prom_buf);
+	return new MS5611_SPI(PX4_SPI_BUS_SENSORS, (spi_dev_e)PX4_SPIDEV_BARO, prom_buf);
 }
 
 MS5611_SPI::MS5611_SPI(int bus, spi_dev_e device, ms5611::prom_u &prom_buf) :

src/drivers/px4fmu/fmu.cpp

@@ -92,6 +92,7 @@ public:
 		MODE_2PWM,
 		MODE_4PWM,
 		MODE_6PWM,
+		MODE_8PWM,
 	};
 	PX4FMU();
 	virtual ~PX4FMU();
@@ -113,6 +114,9 @@ private:
 #if defined(CONFIG_ARCH_BOARD_PX4FMU_V2)
 	static const unsigned _max_actuators = 6;
 #endif
+#if defined(CONFIG_ARCH_BOARD_AEROCORE)
+	static const unsigned _max_actuators = 8;
+#endif
 
 	Mode		_mode;
 	unsigned	_pwm_default_rate;
@@ -203,6 +207,21 @@ const PX4FMU::GPIOConfig PX4FMU::_gpio_tab[] = {
 	{GPIO_VDD_5V_HIPOWER_OC, 0,                       0},
 	{GPIO_VDD_5V_PERIPH_OC,  0,                       0},
 #endif
+#if defined(CONFIG_ARCH_BOARD_AEROCORE)
+	/* AeroCore breaks out User GPIOs on J11 */
+	{GPIO_GPIO0_INPUT,       GPIO_GPIO0_OUTPUT,       0},
+	{GPIO_GPIO1_INPUT,       GPIO_GPIO1_OUTPUT,       0},
+//	{GPIO_GPIO2_INPUT,       GPIO_GPIO2_OUTPUT,       0},
+	{GPIO_GPIO3_INPUT,       GPIO_GPIO3_OUTPUT,       0},
+	{GPIO_GPIO4_INPUT,       GPIO_GPIO4_OUTPUT,       0},
+	{GPIO_GPIO5_INPUT,       GPIO_GPIO5_OUTPUT,       0},
+	{GPIO_GPIO6_INPUT,       GPIO_GPIO6_OUTPUT,       0},
+	{GPIO_GPIO7_INPUT,       GPIO_GPIO7_OUTPUT,       0},
+	{GPIO_GPIO8_INPUT,       GPIO_GPIO8_OUTPUT,       0},
+	{GPIO_GPIO9_INPUT,       GPIO_GPIO9_OUTPUT,       0},
+	{GPIO_GPIO10_INPUT,      GPIO_GPIO10_OUTPUT,      0},
+	{GPIO_GPIO11_INPUT,      GPIO_GPIO11_OUTPUT,      0},
+#endif
 };
 
 const unsigned PX4FMU::_ngpio = sizeof(PX4FMU::_gpio_tab) / sizeof(PX4FMU::_gpio_tab[0]);
@@ -382,6 +401,20 @@ PX4FMU::set_mode(Mode mode)
 
 		break;
 
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+	case MODE_8PWM: // AeroCore PWMs as 8 PWM outs
+		debug("MODE_8PWM");
+		/* default output rates */
+		_pwm_default_rate = 50;
+		_pwm_alt_rate = 50;
+		_pwm_alt_rate_channels = 0;
+
+		/* XXX magic numbers */
+		up_pwm_servo_init(0xff);
+		set_pwm_rate(_pwm_alt_rate_channels, _pwm_default_rate, _pwm_alt_rate);
+		break;
+#endif
+
 	case MODE_NONE:
 		debug("MODE_NONE");
 
@@ -602,6 +635,9 @@ PX4FMU::task_main()
 					num_outputs = 6;
 					break;
 
+				case MODE_8PWM:
+					num_outputs = 8;
+					break;
 				default:
 					num_outputs = 0;
 					break;
@@ -757,6 +793,9 @@ PX4FMU::ioctl(file *filp, int cmd, unsigned long arg)
 	case MODE_2PWM:
 	case MODE_4PWM:
 	case MODE_6PWM:
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+	case MODE_8PWM:
+#endif
 		ret = pwm_ioctl(filp, cmd, arg);
 		break;
 
@@ -986,6 +1025,15 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg)
 			break;
 		}
 
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+	case PWM_SERVO_SET(7):
+	case PWM_SERVO_SET(6):
+		if (_mode < MODE_8PWM) {
+			ret = -EINVAL;
+			break;
+		}
+#endif
+
 	case PWM_SERVO_SET(5):
 	case PWM_SERVO_SET(4):
 		if (_mode < MODE_6PWM) {
@@ -1013,6 +1061,15 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg)
 
 		break;
 
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+	case PWM_SERVO_GET(7):
+	case PWM_SERVO_GET(6):
+		if (_mode < MODE_8PWM) {
+			ret = -EINVAL;
+			break;
+		}
+#endif
+
 	case PWM_SERVO_GET(5):
 	case PWM_SERVO_GET(4):
 		if (_mode < MODE_6PWM) {
@@ -1040,12 +1097,22 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg)
 	case PWM_SERVO_GET_RATEGROUP(3):
 	case PWM_SERVO_GET_RATEGROUP(4):
 	case PWM_SERVO_GET_RATEGROUP(5):
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+	case PWM_SERVO_GET_RATEGROUP(6):
+	case PWM_SERVO_GET_RATEGROUP(7):
+#endif
 		*(uint32_t *)arg = up_pwm_servo_get_rate_group(cmd - PWM_SERVO_GET_RATEGROUP(0));
 		break;
 
 	case PWM_SERVO_GET_COUNT:
 	case MIXERIOCGETOUTPUTCOUNT:
 		switch (_mode) {
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+		case MODE_8PWM:
+			*(unsigned *)arg = 8;
+			break;
+#endif
+
 		case MODE_6PWM:
 			*(unsigned *)arg = 6;
 			break;
@@ -1091,6 +1158,11 @@ PX4FMU::pwm_ioctl(file *filp, int cmd, unsigned long arg)
 			set_mode(MODE_6PWM);
 			break;
 #endif
+#if defined(CONFIG_ARCH_BOARD_AEROCORE)
+		case 8:
+			set_mode(MODE_8PWM);
+			break;
+#endif
 
 		default:
 			ret = -EINVAL;
@@ -1181,10 +1253,17 @@ PX4FMU::write(file *filp, const char *buffer, size_t len)
 	unsigned count = len / 2;
 	uint16_t values[6];
 
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+	if (count > 8) {
+		// we have at most 8 outputs
+		count = 8;
+	}
+#else
 	if (count > 6) {
 		// we have at most 6 outputs
 		count = 6;
 	}
+#endif
 
 	// allow for misaligned values
 	memcpy(values, buffer, count * 2);
@@ -1458,6 +1537,9 @@ fmu_new_mode(PortMode new_mode)
 #endif
 #if defined(CONFIG_ARCH_BOARD_PX4FMU_V2)
 		servo_mode = PX4FMU::MODE_6PWM;
+#endif
+#if defined(CONFIG_ARCH_BOARD_AEROCORE)
+		servo_mode = PX4FMU::MODE_8PWM;
 #endif
 		break;
 
@@ -1776,7 +1858,7 @@ fmu_main(int argc, char *argv[])
 	fprintf(stderr, "FMU: unrecognised command %s, try:\n", verb);
 #if defined(CONFIG_ARCH_BOARD_PX4FMU_V1)
 	fprintf(stderr, "  mode_gpio, mode_serial, mode_pwm, mode_gpio_serial, mode_pwm_serial, mode_pwm_gpio, test\n");
-#elif defined(CONFIG_ARCH_BOARD_PX4FMU_V2)
+#elif defined(CONFIG_ARCH_BOARD_PX4FMU_V2) || defined(CONFIG_ARCH_BOARD_AEROCORE)
 	fprintf(stderr, "  mode_gpio, mode_pwm, test, sensor_reset [milliseconds]\n");
 #endif
 	exit(1);

src/drivers/stm32/adc/adc.cpp

@@ -419,6 +419,10 @@ adc_main(int argc, char *argv[])
 		g_adc = new ADC((1 << 2) | (1 << 3) | (1 << 4) | 
 			(1 << 10) | (1 << 11) | (1 << 12) | (1 << 13) | (1 << 14) | (1 << 15));
 #endif
+#ifdef CONFIG_ARCH_BOARD_AEROCORE
+		/* XXX this hardcodes the default channel set for AeroCore - should be configurable */
+		g_adc = new ADC((1 << 10) | (1 << 11) | (1 << 12) | (1 << 13));
+#endif
 
 		if (g_adc == nullptr)
 			errx(1, "couldn't allocate the ADC driver");

src/drivers/stm32/drv_hrt.c

@@ -141,7 +141,7 @@
 # define HRT_TIMER_POWER_REG	STM32_RCC_APB1ENR
 # define HRT_TIMER_POWER_BIT	RCC_APB2ENR_TIM10EN
 # define HRT_TIMER_VECTOR	STM32_IRQ_TIM1UP
-# define HRT_TIMER_CLOCK	STM32_APB1_TIM10_CLKIN
+# define HRT_TIMER_CLOCK	STM32_APB2_TIM10_CLKIN
 # if CONFIG_STM32_TIM10
 #  error must not set CONFIG_STM32_TIM11=y and HRT_TIMER=10
 # endif
@@ -150,7 +150,7 @@
 # define HRT_TIMER_POWER_REG	STM32_RCC_APB1ENR
 # define HRT_TIMER_POWER_BIT	RCC_APB2ENR_TIM11EN
 # define HRT_TIMER_VECTOR	STM32_IRQ_TIM1TRGCOM
-# define HRT_TIMER_CLOCK	STM32_APB1_TIM11_CLKIN
+# define HRT_TIMER_CLOCK	STM32_APB2_TIM11_CLKIN
 # if CONFIG_STM32_TIM11
 #  error must not set CONFIG_STM32_TIM11=y and HRT_TIMER=11
 # endif