New Crowdin translations - uk (#25558)

Co-authored-by: Crowdin Bot <support+bot@crowdin.com>

docs/uk/telemetry/crsf_telemetry.md

@@ -77,36 +77,36 @@ To use this feature you must build and upload custom firmware that includes [crs
 
 1. [Setup a development environment](../dev_setup/dev_env.md) for building PX4.
 
-  As part of this process you will have used `git` to fetch source code into the **PX4-Autopilot** directory.
+   As part of this process you will have used `git` to fetch source code into the **PX4-Autopilot** directory.
 
 2. Open a terminal and `cd` into the `PX4-Autopilot` directory.
 
-  ```sh
-  cd PX4-Autopilot
-  ```
+   ```sh
+   cd PX4-Autopilot
+   ```
 
 3. Launch the [PX4 board config tool (`menuconfig`)](../hardware/porting_guide_config.md#px4-menuconfig-setup) for your `make` target using the `boardconfig` option (here the target is the [ARK Electronics ARKV6X](../flight_controller/ark_v6x.md) flight controller):
 
-  ```sh
-  make ark_fmu-v6x_default boardconfig
-  ```
+   ```sh
+   make ark_fmu-v6x_default boardconfig
+   ```
 
 4. У інструменті конфігурації плати PX4:
 
-  - Disable the default `rc_input` module
-    1. Navigate to the `drivers` submenu, then scroll down to highlight `rc_input`.
-    2. Use the enter key to remove the `*` from `rc_input` checkbox.
-  - Enable the `crsf_rc` module
-    1. Scroll to highlight the `RC` submenu, then press enter to open it.
-    2. Scroll to highlight `crsf_rc` and press enter to enable it.
+   - Disable the default `rc_input` module
+     1. Navigate to the `drivers` submenu, then scroll down to highlight `rc_input`.
+     2. Use the enter key to remove the `*` from `rc_input` checkbox.
+   - Enable the `crsf_rc` module
+     1. Scroll to highlight the `RC` submenu, then press enter to open it.
+     2. Scroll to highlight `crsf_rc` and press enter to enable it.
 
-  Збережіть і вийдіть з інструменту конфігурації плати PX4.
+   Збережіть і вийдіть з інструменту конфігурації плати PX4.
 
 5. [Build the PX4 source code](../dev_setup/building_px4.md) with your changes (again assuming you are using ARKV6X):
 
-  ```sh
-  make ark_fmu-v6x_default
-  ```
+   ```sh
+   make ark_fmu-v6x_default
+   ```
 
 Це побудує вашу власну прошивку, яку зараз потрібно завантажити на ваш контролер польоту.
 
@@ -128,11 +128,11 @@ Alternatively you can use QGroundControl to install the firmware, as described i
 
 1. [RC_CRSF_PRT_CFG](../advanced_config/parameter_reference.md#RC_CRSF_PRT_CFG) — Set to the port that is connected to the CRSF receiver (such as `TELEM1`).
 
-  This [configures the serial port](../peripherals/serial_configuration.md) to use the CRSF protocol.
-  Note that some serial ports may already have a [default serial port mapping](../peripherals/serial_configuration.md#default-serial-port-configuration) or [default MAVLink serial port mapping](../peripherals/mavlink_peripherals.md#default-mavlink-ports) that you will have to un-map before you can assign the port to CRSF.
-  For example, if you want to use `TELEM1` or `TELEM2` you first need to modify [MAV_0_CONFIG](../advanced_config/parameter_reference.md#MAV_0_CONFIG) or [MAV_1_CONFIG](../advanced_config/parameter_reference.md#MAV_1_CONFIG) to stop setting those ports.
+   This [configures the serial port](../peripherals/serial_configuration.md) to use the CRSF protocol.
+   Note that some serial ports may already have a [default serial port mapping](../peripherals/serial_configuration.md#default-serial-port-configuration) or [default MAVLink serial port mapping](../peripherals/mavlink_peripherals.md#default-mavlink-ports) that you will have to un-map before you can assign the port to CRSF.
+   For example, if you want to use `TELEM1` or `TELEM2` you first need to modify [MAV_0_CONFIG](../advanced_config/parameter_reference.md#MAV_0_CONFIG) or [MAV_1_CONFIG](../advanced_config/parameter_reference.md#MAV_1_CONFIG) to stop setting those ports.
 
-  Немає потреби встановлювати швидкість передачі для порту, оскільки це налаштовано драйвером.
+   Немає потреби встановлювати швидкість передачі для порту, оскільки це налаштовано драйвером.
 
 2. [RC_CRSF_TEL_EN](../advanced_config/parameter_reference.md#RC_CRSF_TEL_EN) — Enable to activate Crossfire telemetry.
 

docs/uk/telemetry/jfi_telemetry.md

@@ -111,9 +111,9 @@ However if you change the baud rate from 57600 you will need to create and use a
 
 1. Disable SiK Radio in QGC (**Application Settings → General → AutoConnect**).
 2. Create a new link configuration:
-  - Go to **Application Settings → Comms Links**.
-  - Click **Add**.
-  - Set **Type** to **Serial**, configure the **Serial Port** and **Baud Rate** to match the J.Fi device.
+   - Go to **Application Settings → Comms Links**.
+   - Click **Add**.
+   - Set **Type** to **Serial**, configure the **Serial Port** and **Baud Rate** to match the J.Fi device.
 3. Select **Connect** to connect with the new configuration.
 
 ## J.Fi Configuration