mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-10-27 02:43:33 +08:00
Initial build for Crazyflie 2.0
Working crazyflie firmware build * Console on USART3 * Could not disable building PX4IO firmware, currently commented out Don't build PX4IO firmware if the board doesn't ask for it Added crazyflie motor driver Fixed wrong register CLK_SEL is in PWR_MGMT_1 Initial I2C/SPI MPU9250 device * Tested with I2C * Need to add error checking * Intermittent crash on stop call Working ak8963 mag driver Functional lps25h driver. Work in progress. Works well enough to probe and allow sensors task to start. Added serial port test module HACK! Get sensors module working Set crazyflie PWM range Extend baudrate for Crazyflie's NRF radio Added dummy tone alarm to allow for init Added autostart script for Crazyflie
This commit is contained in:
Tim Dyer
@@ -0,0 +1,261 @@
|
||||
/************************************************************************************
|
||||
* configs/crazyflie/include/board.h
|
||||
* include/arch/board/board.h
|
||||
*
|
||||
* Copyright (C) 2012 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __CONFIG_CRAZYFLIE_INCLUDE_BOARD_H
|
||||
#define __CONFIG_CRAZYFLIE_INCLUDE_BOARD_H
|
||||
|
||||
/************************************************************************************
|
||||
* Included Files
|
||||
************************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
# include <stdint.h>
|
||||
#endif
|
||||
|
||||
#include "stm32_rcc.h"
|
||||
#include "stm32_sdio.h"
|
||||
#include "stm32.h"
|
||||
|
||||
/************************************************************************************
|
||||
* Definitions
|
||||
************************************************************************************/
|
||||
|
||||
/* Clocking *************************************************************************/
|
||||
/* The PX4FMU uses a 24MHz crystal connected to the HSE.
|
||||
*
|
||||
* This is the canonical configuration:
|
||||
* System Clock source : PLL (HSE)
|
||||
* SYSCLK(Hz) : 168000000 Determined by PLL configuration
|
||||
* HCLK(Hz) : 168000000 (STM32_RCC_CFGR_HPRE)
|
||||
* AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE)
|
||||
* APB1 Prescaler : 4 (STM32_RCC_CFGR_PPRE1)
|
||||
* APB2 Prescaler : 2 (STM32_RCC_CFGR_PPRE2)
|
||||
* HSE Frequency(Hz) : 24000000 (STM32_BOARD_XTAL)
|
||||
* PLLM : 24 (STM32_PLLCFG_PLLM)
|
||||
* PLLN : 336 (STM32_PLLCFG_PLLN)
|
||||
* PLLP : 2 (STM32_PLLCFG_PLLP)
|
||||
* PLLQ : 7 (STM32_PLLCFG_PLLQ)
|
||||
* Main regulator output voltage : Scale1 mode Needed for high speed SYSCLK
|
||||
* Flash Latency(WS) : 5
|
||||
* Prefetch Buffer : OFF
|
||||
* Instruction cache : ON
|
||||
* Data cache : ON
|
||||
* Require 48MHz for USB OTG FS, : Enabled
|
||||
* SDIO and RNG clock
|
||||
*/
|
||||
|
||||
/* HSI - 16 MHz RC factory-trimmed
|
||||
* LSI - 32 KHz RC
|
||||
* HSE - On-board crystal frequency is 24MHz
|
||||
* LSE - not installed
|
||||
*/
|
||||
|
||||
#define STM32_BOARD_XTAL 8000000ul
|
||||
|
||||
#define STM32_HSI_FREQUENCY 16000000ul
|
||||
#define STM32_LSI_FREQUENCY 32000
|
||||
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
|
||||
//#define STM32_LSE_FREQUENCY 32768
|
||||
|
||||
/* Main PLL Configuration.
|
||||
*
|
||||
* PLL source is HSE
|
||||
* PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN
|
||||
* = (8,000,000 / 8) * 336
|
||||
* = 336,000,000
|
||||
* SYSCLK = PLL_VCO / PLLP
|
||||
* = 336,000,000 / 2 = 168,000,000
|
||||
* USB OTG FS, SDIO and RNG Clock
|
||||
* = PLL_VCO / PLLQ
|
||||
* = 48,000,000
|
||||
*/
|
||||
|
||||
#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(8)
|
||||
#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336)
|
||||
#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2
|
||||
#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7)
|
||||
|
||||
#define STM32_SYSCLK_FREQUENCY 168000000ul
|
||||
|
||||
/* AHB clock (HCLK) is SYSCLK (168MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
|
||||
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
|
||||
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */
|
||||
|
||||
/* APB1 clock (PCLK1) is HCLK/4 (42MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */
|
||||
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4)
|
||||
|
||||
/* Timers driven from APB1 will be twice PCLK1 */
|
||||
|
||||
#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||||
|
||||
/* APB2 clock (PCLK2) is HCLK/2 (84MHz) */
|
||||
|
||||
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */
|
||||
#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2)
|
||||
|
||||
/* Timers driven from APB2 will be twice PCLK2 */
|
||||
|
||||
#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||||
|
||||
/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
|
||||
* otherwise frequency is 2xAPBx.
|
||||
* Note: TIM1,8 are on APB2, others on APB1
|
||||
*/
|
||||
|
||||
#define STM32_TIM18_FREQUENCY (2*STM32_PCLK2_FREQUENCY)
|
||||
#define STM32_TIM27_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
|
||||
|
||||
/* Alternate function pin selections ************************************************/
|
||||
|
||||
/*
|
||||
* UARTs.
|
||||
*
|
||||
*/
|
||||
#define GPIO_USART2_RX GPIO_USART2_RX_1
|
||||
#define GPIO_USART2_TX GPIO_USART2_TX_1
|
||||
|
||||
#define GPIO_USART3_RX GPIO_USART3_RX_2
|
||||
#define GPIO_USART3_TX GPIO_USART3_TX_2
|
||||
|
||||
#define GPIO_USART6_RX GPIO_USART6_RX_1
|
||||
#define GPIO_USART6_TX GPIO_USART6_TX_1
|
||||
|
||||
/* UART DMA configuration for USART6 */
|
||||
#define DMAMAP_USART6_RX DMAMAP_USART6_RX_2
|
||||
|
||||
/*
|
||||
* I2C
|
||||
*
|
||||
* The optional _GPIO configurations allow the I2C driver to manually
|
||||
* reset the bus to clear stuck slaves. They match the pin configuration,
|
||||
* but are normally-high GPIOs.
|
||||
*/
|
||||
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1
|
||||
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1
|
||||
#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN6)
|
||||
#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN7)
|
||||
|
||||
#define GPIO_I2C3_SCL GPIO_I2C3_SCL_1
|
||||
#define GPIO_I2C3_SDA GPIO_I2C3_SDA_1
|
||||
#define GPIO_I2C3_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN8)
|
||||
#define GPIO_I2C3_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN9)
|
||||
|
||||
/*
|
||||
* SPI
|
||||
*
|
||||
* There are sensors on SPI1, and SPI3 is connected to the microSD slot.
|
||||
*/
|
||||
#define GPIO_SPI1_MISO (GPIO_SPI1_MISO_1|GPIO_SPEED_50MHz)
|
||||
#define GPIO_SPI1_MOSI (GPIO_SPI1_MOSI_1|GPIO_SPEED_50MHz)
|
||||
#define GPIO_SPI1_SCK (GPIO_SPI1_SCK_1|GPIO_SPEED_50MHz)
|
||||
|
||||
/* XXX since we allocate the HP work stack from CCM RAM on normal system startup,
|
||||
SPI1 will never run in DMA mode - so we can just give it a random config here.
|
||||
What we really need to do is to make DMA configurable per channel, and always
|
||||
disable it for SPI1. */
|
||||
#define DMACHAN_SPI1_RX DMAMAP_SPI1_RX_1
|
||||
#define DMACHAN_SPI1_TX DMAMAP_SPI1_TX_2
|
||||
|
||||
/************************************************************************************
|
||||
* Public Data
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
#define EXTERN extern "C"
|
||||
extern "C" {
|
||||
#else
|
||||
#define EXTERN extern
|
||||
#endif
|
||||
|
||||
/************************************************************************************
|
||||
* Public Function Prototypes
|
||||
************************************************************************************/
|
||||
/************************************************************************************
|
||||
* Name: stm32_boardinitialize
|
||||
*
|
||||
* Description:
|
||||
* All STM32 architectures must provide the following entry point. This entry point
|
||||
* is called early in the intitialization -- after all memory has been configured
|
||||
* and mapped but before any devices have been initialized.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
EXTERN void stm32_boardinitialize(void);
|
||||
|
||||
/************************************************************************************
|
||||
* Name: stm32_ledinit, stm32_setled, and stm32_setleds
|
||||
*
|
||||
* Description:
|
||||
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LEDs. If
|
||||
* CONFIG_ARCH_LEDS is not defined, then the following interfacesare available to
|
||||
* control the LEDs from user applications.
|
||||
*
|
||||
************************************************************************************/
|
||||
|
||||
#ifndef CONFIG_ARCH_LEDS
|
||||
EXTERN void stm32_ledinit(void);
|
||||
EXTERN void stm32_setled(int led, bool ledon);
|
||||
EXTERN void stm32_setleds(uint8_t ledset);
|
||||
#endif
|
||||
|
||||
#undef EXTERN
|
||||
#if defined(__cplusplus)
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
#endif /* __CONFIG_CRAZYFLIE_INCLUDE_BOARD_H */
|
||||
@@ -0,0 +1,42 @@
|
||||
/****************************************************************************
|
||||
*
|
||||
* Copyright (C) 2013 PX4 Development Team. All rights reserved.
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name PX4 nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/**
|
||||
* nsh_romfsetc.h
|
||||
*
|
||||
* This file is a stub for 'make export' purposes; the actual ROMFS
|
||||
* must be supplied by the library client.
|
||||
*/
|
||||
|
||||
extern unsigned char romfs_img[];
|
||||
extern unsigned int romfs_img_len;
|
||||
Reference in New Issue
Block a user