fly316/PX4-Autopilot
7
0
Fork 0
mirror of https://gitee.com/mirrors_PX4/PX4-Autopilot.git synced 2026-10-27 05:53:34 +08:00
Code Issues Packages Projects Releases Wiki Activity

Move PX4 Guide source into /docs (#24490)

Browse Source 
* Add vitepress tree

* Update existing workflows so they dont trigger on changes in the docs path

* Add nojekyll, package.json, LICENCE etc

* Add crowdin docs upload/download scripts

* Add docs flaw checker workflows

* Used docs prefix for docs workflows

* Crowdin obvious fixes

* ci: docs move to self hosted runner

runs on a beefy server for faster builds

Signed-off-by: Ramon Roche <mrpollo@gmail.com>

* ci: don't run build action for docs or ci changes

Signed-off-by: Ramon Roche <mrpollo@gmail.com>

* ci: update runners

Signed-off-by: Ramon Roche <mrpollo@gmail.com>

* Add docs/en

* Add docs assets and scripts

* Fix up editlinks to point to PX4 sources

* Download just the translations that are supported

* Add translation sources for zh, uk, ko

* Update latest tranlsation and uorb graphs

* update vitepress to latest

---------

Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
This commit is contained in:
Hamish Willee
2025-03-13 16:08:27 +11:00
committed by GitHub
co-authored by Ramon Roche
parent 8e6d2ebe4a
commit 88d623bedb
5176 changed files with 558771 additions and 2 deletions
Download Patch File Download Diff File Expand all files Collapse all files
docs/ko/peripherals/vesc.md
+58
View File
@@ -0,0 +1,58 @@
# VESC ESCs (DroneCAN)
The [VESC project](https://vesc-project.com/) is a fully open source hardware and software design for advanced FOC motor controllers.
While it can be controlled using traditional PWM input, it also supports being connected over CAN bus using [DroneCAN](../dronecan/index.md).
## 구매처
[Vesc Project > Hardware](https://vesc-project.com/Hardware)
## 하드웨어 설정
### 배선
ESCs are connected to the CAN bus using the VESC CAN connector. Note that this is _not_ the Pixhawk standard 4 pin JST GH connector. For more information, refer to the [CAN Wiring](../can/index.md#wiring) instructions. ESC order does not matter.
## Firmware Setup
The preferred tool for motor enumeration is the [VESC tool](https://vesc-project.com/vesc_tool).
In addition to the normal motor configuration that you will have to setup in the VESC tool, you will also need to properly setup the app configuration.
The recommended app setup is as follows:
| 매개변수 | Option |
| ----------------------- | ---------------------- |
| App to use | `No App` |
| VESC ID | `1,2,...` |
| Can Status Message Mode | `CAN_STATUS_1_2_3_4_5` |
| CAN Baud Rate | `CAN_BAUD_500K` |
| CAN Mode | `UAVCAN` |
| UAVCAN ESC Index | `0,1,...` |
VESC ID should have the same motor numbering as in PX4 convention, starting at `1` for top-right motor, `2` for bottom-left motor etc.
However the `UAVCAN ESC Index` starts from `0`, and as such it is always one index lower than the `VESC ID`.
For example, in a quadcopter the bottom left motor will have `VESC ID = 2` and `UAVCAN ESC Index = 1`.
Finally the `CAN Baud Rate` must match the value set in [UAVCAN_BITRATE](../advanced_config/parameter_reference.md#UAVCAN_BITRATE).
## Flight Controller Setup
### Enable DroneCAN
Connect the ESCs to the Pixhawk CAN bus. Power up the entire vehicle using a battery or power supply (not just the flight controller over USB) and enable the DroneCAN driver by setting the parameter [UAVCAN_ENABLE](../advanced_config/parameter_reference.md#UAVCAN_ENABLE) to `3` to enable both dynamic node ID allocation and DroneCAN ESC output.
### PX4 설정
Assign motors to outputs using the [Acutator](../config/actuators.md#actuator-testing) configuration screen.
<!-- removed as there is no info for it in linked doc -->
<!--
## Troubleshooting
See DroneCAN Troubleshooting - (index.md#troubleshooting).
-->
## 추가 정보
- [VESC Project ESCs](https://vesc-project.com/)
- [Benjamin Vedder's blog](http://vedder.se) (project owner)