New Crowdin translations - uk (#24949)

Co-authored-by: Crowdin Bot <support+bot@crowdin.com>

docs/uk/msg_docs/AirspeedValidated.md

@@ -1,21 +1,27 @@
 # AirspeedValidated (повідомлення UORB)
 
-[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/AirspeedValidated.msg)
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/versioned/AirspeedValidated.msg)
 
 ```c
+uint32 MESSAGE_VERSION = 1
+
 uint64 timestamp				# time since system start (microseconds)
 
-float32 indicated_airspeed_m_s			# indicated airspeed in m/s (IAS), set to NAN if invalid
-float32 calibrated_airspeed_m_s     		# calibrated airspeed in m/s (CAS, accounts for instrumentation errors), set to NAN if invalid
-float32 true_airspeed_m_s			# true filtered airspeed in m/s (TAS), set to NAN if invalid
+float32 indicated_airspeed_m_s			# [m/s] Indicated airspeed (IAS), set to NAN if invalid
+float32 calibrated_airspeed_m_s     		# [m/s] Calibrated airspeed (CAS), set to NAN if invalid
+float32 true_airspeed_m_s			# [m/s] True airspeed (TAS), set to NAN if invalid
 
+int8 airspeed_source				# Source of currently published airspeed values
+int8 DISABLED = -1
+int8 GROUND_MINUS_WIND = 0
+int8 SENSOR_1 = 1
+int8 SENSOR_2 = 2
+int8 SENSOR_3 = 3
+int8 SYNTHETIC = 4
+
+# debug states
 float32 calibrated_ground_minus_wind_m_s 	# CAS calculated from groundspeed - windspeed, where windspeed is estimated based on a zero-sideslip assumption, set to NAN if invalid
-float32 true_ground_minus_wind_m_s 		# TAS calculated from groundspeed - windspeed, where windspeed is estimated based on a zero-sideslip assumption, set to NAN if invalid
-
-bool airspeed_sensor_measurement_valid 		# True if data from at least one airspeed sensor is declared valid.
-
-int8 selected_airspeed_index 			# 1-3: airspeed sensor index, 0: groundspeed-windspeed, -1: airspeed invalid
-
+float32 calibraded_airspeed_synth_m_s		# synthetic airspeed in m/s, set to NAN if invalid
 float32 airspeed_derivative_filtered		# filtered indicated airspeed derivative [m/s/s]
 float32 throttle_filtered			# filtered fixed-wing throttle [-]
 float32 pitch_filtered				# filtered pitch [rad]

docs/uk/msg_docs/AirspeedValidatedV0.md

@@ -0,0 +1,25 @@
+# AirspeedValidatedV0 (UORB message)
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/px4_msgs_old/msg/AirspeedValidatedV0.msg)
+
+```c
+uint32 MESSAGE_VERSION = 0
+
+uint64 timestamp				# time since system start (microseconds)
+
+float32 indicated_airspeed_m_s			# indicated airspeed in m/s (IAS), set to NAN if invalid
+float32 calibrated_airspeed_m_s     		# calibrated airspeed in m/s (CAS, accounts for instrumentation errors), set to NAN if invalid
+float32 true_airspeed_m_s			# true filtered airspeed in m/s (TAS), set to NAN if invalid
+
+float32 calibrated_ground_minus_wind_m_s 	# CAS calculated from groundspeed - windspeed, where windspeed is estimated based on a zero-sideslip assumption, set to NAN if invalid
+float32 true_ground_minus_wind_m_s 		# TAS calculated from groundspeed - windspeed, where windspeed is estimated based on a zero-sideslip assumption, set to NAN if invalid
+
+bool airspeed_sensor_measurement_valid 		# True if data from at least one airspeed sensor is declared valid.
+
+int8 selected_airspeed_index 			# 1-3: airspeed sensor index, 0: groundspeed-windspeed, -1: airspeed invalid
+
+float32 airspeed_derivative_filtered		# filtered indicated airspeed derivative [m/s/s]
+float32 throttle_filtered			# filtered fixed-wing throttle [-]
+float32 pitch_filtered				# filtered pitch [rad]
+
+```

docs/uk/msg_docs/CellularStatus.md

@@ -1,35 +1,49 @@
 # CellularStatus (повідомлення UORB)
 
+Cellular status
+
+This is currently used only for logging cell status from MAVLink.
+
 [source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/CellularStatus.msg)
 
 ```c
-uint64 timestamp	# time since system start (microseconds)
+# Cellular status
+#
+# This is currently used only for logging cell status from MAVLink.
 
-uint8 CELLULAR_STATUS_FLAG_UNKNOWN=0 # State unknown or not reportable
-uint8 CELLULAR_STATUS_FLAG_FAILED=1 # velocity setpoint
-uint8 CELLULAR_STATUS_FLAG_INITIALIZING=2 # Modem is being initialized
-uint8 CELLULAR_STATUS_FLAG_LOCKED=3	# Modem is locked
-uint8 CELLULAR_STATUS_FLAG_DISABLED=4	# Modem is not enabled and is powered down
-uint8 CELLULAR_STATUS_FLAG_DISABLING=5	# Modem is currently transitioning to the CELLULAR_STATUS_FLAG_DISABLED state
-uint8 CELLULAR_STATUS_FLAG_ENABLING=6 	# Modem is currently transitioning to the CELLULAR_STATUS_FLAG_ENABLED state
-uint8 CELLULAR_STATUS_FLAG_ENABLED=7  # Modem is enabled and powered on but not registered with a network provider and not available for data connections
-uint8 CELLULAR_STATUS_FLAG_SEARCHING=8  # Modem is searching for a network provider to register
-uint8 CELLULAR_STATUS_FLAG_REGISTERED=9  # Modem is registered with a network provider, and data connections and messaging may be available for use
-uint8 CELLULAR_STATUS_FLAG_DISCONNECTING=10  # Modem is disconnecting and deactivating the last active packet data bearer. This state will not be entered if more than one packet data bearer is active and one of the active bearers is deactivated
-uint8 CELLULAR_STATUS_FLAG_CONNECTING=11  # Modem is activating and connecting the first packet data bearer. Subsequent bearer activations when another bearer is already active do not cause this state to be entered
-uint8 CELLULAR_STATUS_FLAG_CONNECTED=12  # One or more packet data bearers is active and connected
+uint64 timestamp # [us] Time since system start.
 
-uint8 CELLULAR_NETWORK_FAILED_REASON_NONE=0 # No error
-uint8 CELLULAR_NETWORK_FAILED_REASON_UNKNOWN=1 # Error state is unknown
-uint8 CELLULAR_NETWORK_FAILED_REASON_SIM_MISSING=2 # SIM is required for the modem but missing
-uint8 CELLULAR_NETWORK_FAILED_REASON_SIM_ERROR=3 # SIM is available, but not usable for connection
+uint16 status # [@enum STATUS_FLAG] Status bitmap.
+uint16 STATUS_FLAG_UNKNOWN = 1 # State unknown or not reportable.
+uint16 STATUS_FLAG_FAILED = 2 # Modem is unusable.
+uint16 STATUS_FLAG_INITIALIZING = 4 # Modem is being initialized.
+uint16 STATUS_FLAG_LOCKED = 8 # Modem is locked.
+uint16 STATUS_FLAG_DISABLED = 16 # Modem is not enabled and is powered down.
+uint16 STATUS_FLAG_DISABLING = 32 # Modem is currently transitioning to the STATUS_FLAG_DISABLED state.
+uint16 STATUS_FLAG_ENABLING = 64 # Modem is currently transitioning to the STATUS_FLAG_ENABLED state.
+uint16 STATUS_FLAG_ENABLED = 128 # Modem is enabled and powered on but not registered with a network provider and not available for data connections.
+uint16 STATUS_FLAG_SEARCHING = 256 # Modem is searching for a network provider to register.
+uint16 STATUS_FLAG_REGISTERED = 512 # Modem is registered with a network provider, and data connections and messaging may be available for use.
+uint16 STATUS_FLAG_DISCONNECTING = 1024 # Modem is disconnecting and deactivating the last active packet data bearer. This state will not be entered if more than one packet data bearer is active and one of the active bearers is deactivated.
+uint16 STATUS_FLAG_CONNECTING = 2048 # Modem is activating and connecting the first packet data bearer. Subsequent bearer activations when another bearer is already active do not cause this state to be entered.
+uint16 STATUS_FLAG_CONNECTED = 4096 # One or more packet data bearers is active and connected.
 
-uint16 status 	# Status bitmap 1: Roaming is active
-uint8 failure_reason #Failure reason when status in in CELLUAR_STATUS_FAILED
-uint8 type 	# Cellular network radio type 0: none 1: gsm 2: cdma 3: wcdma 4: lte
-uint8 quality	# Cellular network RSSI/RSRP in dBm, absolute value
-uint16 mcc	# Mobile country code. If unknown, set to: UINT16_MAX
-uint16 mnc	# Mobile network code. If unknown, set to: UINT16_MAX
-uint16 lac	# Location area code. If unknown, set to: 0
+uint8 failure_reason # [@enum FAILURE_REASON] Failure reason.
+uint8 FAILURE_REASON_NONE = 0 # No error.
+uint8 FAILURE_REASON_UNKNOWN = 1 # Error state is unknown.
+uint8 FAILURE_REASON_SIM_MISSING = 2 # SIM is required for the modem but missing.
+uint8 FAILURE_REASON_SIM_ERROR = 3 # SIM is available, but not usable for connection.
+
+uint8 type # [@enum CELLULAR_NETWORK_RADIO_TYPE] Cellular network radio type.
+uint8 CELLULAR_NETWORK_RADIO_TYPE_NONE = 0 # None
+uint8 CELLULAR_NETWORK_RADIO_TYPE_GSM = 1 # GSM
+uint8 CELLULAR_NETWORK_RADIO_TYPE_CDMA = 2 # CDMA
+uint8 CELLULAR_NETWORK_RADIO_TYPE_WCDMA = 3 # WCDMA
+uint8 CELLULAR_NETWORK_RADIO_TYPE_LTE = 4 # LTE
+
+uint8 quality # [dBm] Cellular network RSSI/RSRP, absolute value.
+uint16 mcc # [@invalid UINT16_MAX] Mobile country code.
+uint16 mnc # [@invalid UINT16_MAX] Mobile network code.
+uint16 lac # [@invalid 0] Location area code.
 
 ```

docs/uk/msg_docs/FixedWingLateralGuidanceStatus.md

@@ -0,0 +1,23 @@
+# FixedWingLateralGuidanceStatus (UORB message)
+
+Fixed Wing Lateral Guidance Status message
+Published by fw_pos_control module to report the resultant lateral setpoints and NPFG debug outputs
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/FixedWingLateralGuidanceStatus.msg)
+
+```c
+# Fixed Wing Lateral Guidance Status message
+# Published by fw_pos_control module to report the resultant lateral setpoints and NPFG debug outputs
+
+uint64 timestamp                # time since system start (microseconds)
+
+float32 course_setpoint         # [rad] [@range -pi, pi] Desired direction of travel over ground w.r.t (true) North. Set by guidance law
+float32 lateral_acceleration_ff # [m/s^2] [FRD] lateral acceleration demand only for maintaining curvature
+float32 bearing_feas            # [@range 0,1] bearing feasibility
+float32 bearing_feas_on_track   # [@range 0,1] on-track bearing feasibility
+float32 signed_track_error      # [m] signed track error
+float32 track_error_bound       # [m] track error bound
+float32 adapted_period          # [s] adapted period (if auto-tuning enabled)
+uint8 wind_est_valid            # [boolean] true = wind estimate is valid and/or being used by controller (also indicates if wind estimate usage is disabled despite being valid)
+
+```

docs/uk/msg_docs/FixedWingLateralSetpoint.md

@@ -0,0 +1,22 @@
+# FixedWingLateralSetpoint (UORB message)
+
+Fixed Wing Lateral Setpoint message
+Used by the fw_lateral_longitudinal_control module
+At least one of course, airspeed_direction, or lateral_acceleration must be finite.
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/versioned/FixedWingLateralSetpoint.msg)
+
+```c
+# Fixed Wing Lateral Setpoint message
+# Used by the fw_lateral_longitudinal_control module
+# At least one of course, airspeed_direction, or lateral_acceleration must be finite.
+
+uint32 MESSAGE_VERSION = 0
+
+uint64 timestamp                        # time since system start (microseconds)
+
+float32 course 				# [rad] [@range -pi, pi] Desired direction of travel over ground w.r.t (true) North. NAN if not controlled directly.
+float32 airspeed_direction    		# [rad] [@range -pi, pi] Desired horizontal angle of airspeed vector w.r.t. (true) North. Same as vehicle heading if in the absence of sideslip. NAN if not controlled directly, takes precedence over course if finite.
+float32 lateral_acceleration 		# [m/s^2] [FRD] Lateral acceleration setpoint. NAN if not controlled directly, used as feedforward if either course setpoint or airspeed_direction is finite.
+
+```

docs/uk/msg_docs/FixedWingLateralStatus.md

@@ -0,0 +1,17 @@
+# FixedWingLateralStatus (UORB message)
+
+Fixed Wing Lateral Status message
+Published by the fw_lateral_longitudinal_control module to report the resultant lateral setpoint
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/FixedWingLateralStatus.msg)
+
+```c
+# Fixed Wing Lateral Status message
+# Published by the fw_lateral_longitudinal_control module to report the resultant lateral setpoint
+
+uint64 timestamp                         # time since system start (microseconds)
+
+float32 lateral_acceleration_setpoint    # [m/s^2] [FRD] resultant lateral acceleration setpoint
+float32 can_run_factor 	 	         # [norm] [@range 0, 1] estimate of certainty of the correct functionality of the npfg roll setpoint
+
+```

docs/uk/msg_docs/FixedWingLongitudinalSetpoint.md

@@ -0,0 +1,26 @@
+# FixedWingLongitudinalSetpoint (UORB message)
+
+Fixed Wing Longitudinal Setpoint message
+Used by the fw_lateral_longitudinal_control module
+If pitch_direct and throttle_direct are not both finite, then the controller relies on altitude/height_rate and equivalent_airspeed to control vertical motion.
+If both altitude and height_rate are NAN, the controller maintains the current altitude.
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/versioned/FixedWingLongitudinalSetpoint.msg)
+
+```c
+# Fixed Wing Longitudinal Setpoint message
+# Used by the fw_lateral_longitudinal_control module
+# If pitch_direct and throttle_direct are not both finite, then the controller relies on altitude/height_rate and equivalent_airspeed to control vertical motion.
+# If both altitude and height_rate are NAN, the controller maintains the current altitude.
+
+uint32 MESSAGE_VERSION = 0
+
+uint64 timestamp                        # time since system start (microseconds)
+
+float32 altitude  			# [m] Altitude setpoint AMSL, not controlled directly if NAN or if height_rate is finite
+float32 height_rate 			# [m/s] [ENU] Scalar height rate setpoint. NAN if not controlled directly
+float32 equivalent_airspeed 		# [m/s] [@range 0, inf] Scalar equivalent airspeed setpoint. NAN if system default should be used
+float32 pitch_direct 			# [rad] [@range -pi, pi] [FRD] NAN if not controlled, overrides total energy controller
+float32 throttle_direct 		# [norm] [@range 0,1] NAN if not controlled, overrides total energy controller
+
+```

docs/uk/msg_docs/FixedWingRunwayControl.md

@@ -0,0 +1,19 @@
+# FixedWingRunwayControl (UORB message)
+
+Auxiliary control fields for fixed-wing runway takeoff/landing
+
+Passes information from the FixedWingModeManager to the FixedWingAttitudeController
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/FixedWingRunwayControl.msg)
+
+```c
+# Auxiliary control fields for fixed-wing runway takeoff/landing
+
+# Passes information from the FixedWingModeManager to the FixedWingAttitudeController
+
+uint64 timestamp # [us] time since system start
+
+bool wheel_steering_enabled		# Flag that enables the wheel steering.
+float32 wheel_steering_nudging_rate	# [norm] [@range -1, 1] [FRD] Manual wheel nudging, added to controller output. NAN is interpreted as 0.
+
+```

docs/uk/msg_docs/LateralControlConfiguration.md

@@ -0,0 +1,18 @@
+# LateralControlConfiguration (UORB message)
+
+Fixed Wing Lateral Control Configuration message
+Used by the fw_lateral_longitudinal_control module to constrain FixedWingLateralSetpoint messages.
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/versioned/LateralControlConfiguration.msg)
+
+```c
+# Fixed Wing Lateral Control Configuration message
+# Used by the fw_lateral_longitudinal_control module to constrain FixedWingLateralSetpoint messages.
+
+uint32 MESSAGE_VERSION = 0
+
+uint64 timestamp          # time since system start (microseconds)
+
+float32 lateral_accel_max # [m/s^2] currently maps to a maximum roll angle, accel_max = tan(roll_max) * GRAVITY
+
+```

docs/uk/msg_docs/LongitudinalControlConfiguration.md

@@ -0,0 +1,28 @@
+# LongitudinalControlConfiguration (UORB message)
+
+Fixed Wing Longitudinal Control Configuration message
+Used by the fw_lateral_longitudinal_control module and TECS to constrain FixedWingLongitudinalSetpoint messages
+and configure the resultant setpoints.
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/versioned/LongitudinalControlConfiguration.msg)
+
+```c
+# Fixed Wing Longitudinal Control Configuration message
+# Used by the fw_lateral_longitudinal_control module and TECS to constrain FixedWingLongitudinalSetpoint messages
+# and configure the resultant setpoints.
+
+uint32 MESSAGE_VERSION = 0
+
+uint64 timestamp                        # time since system start (microseconds)
+
+float32 pitch_min   			# [rad][@range -pi, pi] defaults to FW_P_LIM_MIN if NAN.
+float32 pitch_max   			# [rad][@range -pi, pi] defaults to FW_P_LIM_MAX if NAN.
+float32 throttle_min 			# [norm] [@range 0,1] deaults to FW_THR_MIN if NAN.
+float32 throttle_max 			# [norm] [@range 0,1] defaults to FW_THR_MAX if NAN.
+float32 climb_rate_target 		# [m/s] target climbrate to change altitude. Defaults to FW_T_CLIMB_MAX if NAN. Not used if height_rate is directly set in FixedWingLongitudinalSetpoint.
+float32 sink_rate_target 		# [m/s] target sinkrate to change altitude. Defaults to FW_T_SINK_MAX if NAN. Not used if height_rate is directly set in FixedWingLongitudinalSetpoint.
+float32 speed_weight 			# [@range 0,2], 0=pitch controls altitude only, 2=pitch controls airspeed only
+bool enforce_low_height_condition 	# [boolean] if true, the altitude controller is configured with an alternative timeconstant for tighter altitude tracking
+bool disable_underspeed_protection 	# [boolean] if true, underspeed handling is disabled in the altitude controller
+
+```

docs/uk/msg_docs/PurePursuitStatus.md

@@ -11,6 +11,4 @@ float32 crosstrack_error     # [m] Shortest distance from the vehicle to the pat
 float32 distance_to_waypoint # [m] Distance from the vehicle to the current waypoint
 float32 bearing_to_waypoint  # [rad] Bearing towards current waypoint
 
-# TOPICS pure_pursuit_status
-
 ```

docs/uk/msg_docs/RateCtrlStatus.md

@@ -9,6 +9,5 @@ uint64 timestamp		# time since system start (microseconds)
 float32 rollspeed_integ
 float32 pitchspeed_integ
 float32 yawspeed_integ
-float32 wheel_rate_integ	# FW only and optional
 
 ```

docs/uk/msg_docs/RoverAttitudeSetpoint.md

@@ -7,6 +7,4 @@ uint64 timestamp # time since system start (microseconds)
 
 float32 yaw_setpoint # [rad] Expressed in NED frame
 
-# TOPICS rover_attitude_setpoint
-
 ```

docs/uk/msg_docs/RoverAttitudeStatus.md

@@ -8,6 +8,4 @@ uint64 timestamp # time since system start (microseconds)
 float32 measured_yaw          # [rad/s] Measured yaw rate
 float32 adjusted_yaw_setpoint # [rad/s] Yaw setpoint that is being tracked (Applied slew rates)
 
-# TOPICS rover_attitude_status
-
 ```

docs/uk/msg_docs/RoverPositionSetpoint.md

@@ -0,0 +1,15 @@
+# RoverPositionSetpoint (UORB message)
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/RoverPositionSetpoint.msg)
+
+```c
+uint64 timestamp # time since system start (microseconds)
+
+float32[2] position_ned # 2-dimensional position setpoint in NED frame [m]
+float32[2] start_ned	# (Optional) 2-dimensional start position in NED frame used to define the line that the rover will track to position_ned [m] (Defaults to vehicle position)
+float32 cruising_speed  # (Optional) Specify rover speed [m/s] (Defaults to maximum speed)
+float32 arrival_speed   # (Optional) Specify arrival speed [m/s] (Defaults to zero)
+
+float32 yaw             # [rad] [-pi,pi] from North. Optional, NAN if not set. Mecanum only. (Defaults to vehicle yaw)
+
+```

docs/uk/msg_docs/RoverRateSetpoint.md

@@ -7,6 +7,4 @@ uint64 timestamp # time since system start (microseconds)
 
 float32 yaw_rate_setpoint # [rad/s] Expressed in NED frame
 
-# TOPICS rover_rate_setpoint
-
 ```

docs/uk/msg_docs/RoverRateStatus.md

@@ -9,6 +9,4 @@ float32 measured_yaw_rate          # [rad/s] Measured yaw rate
 float32 adjusted_yaw_rate_setpoint # [rad/s] Yaw rate setpoint that is being tracked (Applied slew rates)
 float32 pid_yaw_rate_integral      # Integral of the PID for the closed loop yaw rate controller
 
-# TOPICS rover_rate_status
-
 ```

docs/uk/msg_docs/RoverSteeringSetpoint.md

@@ -5,9 +5,8 @@
 ```c
 uint64 timestamp # time since system start (microseconds)
 
-float32 normalized_steering_angle # [-1, 1] Normalized steering angle (Only for Ackermann-steered rovers)
-float32 normalized_speed_diff     # [-1, 1] Normalized speed difference between the left and right wheels of the rover (Only for Differential/Mecanum rovers)
+float32 normalized_steering_angle # [-1, 1] Normalized steering angle (Ackermann only, Positiv: Steer right, Negativ: Steer left)
 
-# TOPICS rover_steering_setpoint
+float32 normalized_speed_diff     # [-1, 1] Normalized speed difference between the left and right wheels of the rover (Differential/Mecanum only, Positiv = Turn right, Negativ: Turn left)
 
 ```

docs/uk/msg_docs/RoverThrottleSetpoint.md

@@ -6,9 +6,7 @@
 
 uint64 timestamp        # time since system start (microseconds)
 
-float32 throttle_body_x # throttle setpoint along body X axis [-1, 1]
-float32 throttle_body_y # throttle setpoint along body Y axis [-1, 1]
-
-# TOPICS rover_throttle_setpoint
+float32 throttle_body_x # throttle setpoint along body X axis [-1, 1] (Positiv = forwards, Negativ = backwards)
+float32 throttle_body_y # throttle setpoint along body Y axis [-1, 1] (Mecanum only, Positiv = right, Negativ = left)
 
 ```

docs/uk/msg_docs/RoverVelocitySetpoint.md

@@ -0,0 +1,12 @@
+# RoverVelocitySetpoint (UORB message)
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/RoverVelocitySetpoint.msg)
+
+```c
+uint64 timestamp # time since system start (microseconds)
+
+float32 speed   # [m/s] [-inf, inf] Speed setpoint (Backwards driving if negative)
+float32 bearing # [rad] [-pi,pi] from North. [invalid: NAN, speed is defined in body x direction]
+float32 yaw 	# [rad] [-pi, pi] (Mecanum only, Optional, defaults to current vehicle yaw) Vehicle yaw setpoint in NED frame
+
+```

docs/uk/msg_docs/RoverVelocityStatus.md

@@ -6,14 +6,10 @@
 uint64 timestamp # time since system start (microseconds)
 
 float32 measured_speed_body_x          # [m/s] Measured speed in body x direction. Positiv: forwards, Negativ: backwards
-float32 speed_body_x_setpoint          # [m/s] Speed setpoint in body x direction. Positiv: forwards, Negativ: backwards
 float32 adjusted_speed_body_x_setpoint # [m/s] Post slew rate speed setpoint in body x direction. Positiv: forwards, Negativ: backwards
-float32 measured_speed_body_y          # [m/s] Measured speed in body y direction. Positiv: right, Negativ: left
-float32 speed_body_y_setpoint          # [m/s] Speed setpoint in body y direction. Positiv: right, Negativ: left (Only for mecanum rovers)
-float32 adjusted_speed_body_y_setpoint # [m/s] Post slew rate speed setpoint in body y direction. Positiv: right, Negativ: left (Only for mecanum rovers)
 float32 pid_throttle_body_x_integral   # Integral of the PID for the closed loop controller of the speed in body x direction
-float32 pid_throttle_body_y_integral   # Integral of the PID for the closed loop controller of the speed in body y direction
-
-# TOPICS rover_velocity_status
+float32 measured_speed_body_y          # [m/s] Measured speed in body y direction. Positiv: right, Negativ: left (Mecanum only)
+float32 adjusted_speed_body_y_setpoint # [m/s] Post slew rate speed setpoint in body y direction. Positiv: right, Negativ: left (Mecanum only)
+float32 pid_throttle_body_y_integral   # Integral of the PID for the closed loop controller of the speed in body y direction (Mecanum only)
 
 ```

docs/uk/msg_docs/TrajectorySetpoint6dof.md

@@ -0,0 +1,23 @@
+# TrajectorySetpoint6dof (UORB message)
+
+Trajectory setpoint in NED frame
+Input to position controller.
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/TrajectorySetpoint6dof.msg)
+
+```c
+# Trajectory setpoint in NED frame
+# Input to position controller.
+
+uint64 timestamp # time since system start (microseconds)
+
+# NED local world frame
+float32[3] position               # in meters
+float32[3] velocity               # in meters/second
+float32[3] acceleration           # in meters/second^2
+float32[3] jerk                   # in meters/second^3 (for logging only)
+
+float32[4] quaternion             # unit quaternion
+float32[3] angular_velocity       # angular velocity in radians/second
+
+```

docs/uk/msg_docs/VehicleAttitudeSetpoint.md

@@ -3,7 +3,7 @@
 [source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/versioned/VehicleAttitudeSetpoint.msg)
 
 ```c
-uint32 MESSAGE_VERSION = 0
+uint32 MESSAGE_VERSION = 1
 
 uint64 timestamp		# time since system start (microseconds)
 
@@ -16,10 +16,6 @@ float32[4] q_d			# Desired quaternion for quaternion control
 # For fixed wings thrust_x is the throttle demand and thrust_y, thrust_z will usually be zero.
 float32[3] thrust_body		# Normalized thrust command in body FRD frame [-1,1]
 
-bool reset_integral	# Reset roll/pitch/yaw integrals (navigation logic change)
-
-bool fw_control_yaw_wheel	# control heading with steering wheel (used for auto takeoff on runway)
-
 # TOPICS vehicle_attitude_setpoint mc_virtual_attitude_setpoint fw_virtual_attitude_setpoint
 
 ```

docs/uk/msg_docs/VehicleAttitudeSetpointV0.md

@@ -0,0 +1,25 @@
+# VehicleAttitudeSetpointV0 (UORB message)
+
+[source file](https://github.com/PX4/PX4-Autopilot/blob/main/msg/px4_msgs_old/msg/VehicleAttitudeSetpointV0.msg)
+
+```c
+uint32 MESSAGE_VERSION = 0
+
+uint64 timestamp		# time since system start (microseconds)
+
+float32 yaw_sp_move_rate	# rad/s (commanded by user)
+
+# For quaternion-based attitude control
+float32[4] q_d			# Desired quaternion for quaternion control
+
+# For clarification: For multicopters thrust_body[0] and thrust[1] are usually 0 and thrust[2] is the negative throttle demand.
+# For fixed wings thrust_x is the throttle demand and thrust_y, thrust_z will usually be zero.
+float32[3] thrust_body		# Normalized thrust command in body FRD frame [-1,1]
+
+bool reset_integral	# Reset roll/pitch/yaw integrals (navigation logic change)
+
+bool fw_control_yaw_wheel	# control heading with steering wheel (used for auto takeoff on runway)
+
+# TOPICS vehicle_attitude_setpoint mc_virtual_attitude_setpoint fw_virtual_attitude_setpoint
+
+```

docs/uk/msg_docs/VehicleCommand.md

@@ -11,127 +11,127 @@ Vehicle Command uORB повідомлення. Використовується
 
 uint32 MESSAGE_VERSION = 0
 
-uint64 timestamp					# time since system start (microseconds)
+uint64 timestamp # [us] Time since system start.
 
-uint16 VEHICLE_CMD_CUSTOM_0 = 0				# test command
-uint16 VEHICLE_CMD_CUSTOM_1 = 1				# test command
-uint16 VEHICLE_CMD_CUSTOM_2 = 2				# test command
-uint16 VEHICLE_CMD_NAV_WAYPOINT = 16			# Navigate to MISSION. |Hold time in decimal seconds. (ignored by fixed wing, time to stay at MISSION for rotary wing)| Acceptance radius in meters (if the sphere with this radius is hit, the MISSION counts as reached)| 0 to pass through the WP, if > 0 radius in meters to pass by WP. Positive value for clockwise orbit, negative value for counter-clockwise orbit. Allows trajectory control.| Desired yaw angle at MISSION (rotary wing)| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_LOITER_UNLIM = 17		# Loiter around this MISSION an unlimited amount of time |Empty| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_LOITER_TURNS = 18		# Loiter around this MISSION for X turns |Turns| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_LOITER_TIME = 19			# Loiter around this MISSION for X seconds |Seconds (decimal)| Empty| Radius around MISSION, in meters. If positive loiter clockwise, else counter-clockwise| Desired yaw angle.| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_RETURN_TO_LAUNCH = 20		# Return to launch location |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_NAV_LAND = 21			# Land at location |Empty| Empty| Empty| Desired yaw angle.| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_TAKEOFF = 22			# Takeoff from ground / hand |Minimum pitch (if airspeed sensor present), desired pitch without sensor| Empty| Empty| Yaw angle (if magnetometer present), ignored without magnetometer| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_PRECLAND = 23			# Attempt a precision landing
-uint16 VEHICLE_CMD_DO_ORBIT = 34			# Start orbiting on the circumference of a circle defined by the parameters. |Radius [m] |Velocity [m/s] |Yaw behaviour |Empty |Latitude/X |Longitude/Y |Altitude/Z |
-uint16 VEHICLE_CMD_DO_FIGUREEIGHT = 35        		# Start flying on the outline of a figure eight defined by the parameters. |Major Radius [m] |Minor Radius [m] |Velocity [m/s] |Orientation |Latitude/X |Longitude/Y |Altitude/Z |
-uint16 VEHICLE_CMD_NAV_ROI = 80				# Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|
-uint16 VEHICLE_CMD_NAV_PATHPLANNING = 81		# Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal, in compass degrees, [0..360]| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|
-uint16 VEHICLE_CMD_NAV_VTOL_TAKEOFF = 84		# Takeoff from ground / hand and transition to fixed wing |Minimum pitch (if airspeed sensor present), desired pitch without sensor| Empty| Empty| Yaw angle (if magnetometer present), ignored without magnetometer| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_VTOL_LAND = 85			# Transition to MC and land at location |Empty| Empty| Empty| Desired yaw angle.| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_NAV_GUIDED_LIMITS = 90		# set limits for external control |timeout - maximum time (in seconds) that external controller will be allowed to control vehicle. 0 means no timeout| absolute altitude min (in meters, AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue.  0 means no lower altitude limit| absolute altitude max (in meters)- if vehicle moves above this alt, the command will be aborted and the mission will continue.  0 means no upper altitude limit| horizontal move limit (in meters, AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_NAV_GUIDED_MASTER = 91		# set id of master controller |System ID| Component ID| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_NAV_DELAY = 93				# Delay the next navigation command a number of seconds or until a specified time |Delay in seconds (decimal, -1 to enable time-of-day fields)| hour (24h format, UTC, -1 to ignore)| minute (24h format, UTC, -1 to ignore)| second (24h format, UTC)| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_NAV_LAST = 95			# NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_CONDITION_DELAY = 112		# Delay mission state machine. |Delay in seconds (decimal)| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_CONDITION_CHANGE_ALT = 113		# Ascend/descend at rate.  Delay mission state machine until desired altitude reached. |Descent / Ascend rate (m/s)| Empty| Empty| Empty| Empty| Empty| Finish Altitude|
-uint16 VEHICLE_CMD_CONDITION_DISTANCE = 114		# Delay mission state machine until within desired distance of next NAV point. |Distance (meters)| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_CONDITION_YAW = 115			# Reach a certain target angle. |target angle: [0-360], 0 is north| speed during yaw change:[deg per second]| direction: negative: counter clockwise, positive: clockwise [-1,1]| relative offset or absolute angle: [ 1,0]| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_CONDITION_LAST = 159			# NOP - This command is only used to mark the upper limit of the CONDITION commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_CONDITION_GATE = 4501		# Wait until passing a threshold |2D coord mode: 0: Orthogonal to planned route | Altitude mode: 0: Ignore altitude| Empty| Empty| Lat| Lon| Alt|
-uint16 VEHICLE_CMD_DO_SET_MODE = 176			# Set system mode. |Mode, as defined by ENUM MAV_MODE| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_JUMP = 177			# Jump to the desired command in the mission list.  Repeat this action only the specified number of times |Sequence number| Repeat count| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_CHANGE_SPEED = 178		# Change speed and/or throttle set points. |Speed type (0=Airspeed, 1=Ground Speed)| Speed  (m/s, -1 indicates no change)| Throttle  ( Percent, -1 indicates no change)| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_SET_HOME = 179			# Changes the home location either to the current location or a specified location. |Use current (1=use current location, 0=use specified location)| Empty| Empty| Empty| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_DO_SET_PARAMETER = 180		# Set a system parameter.  Caution!  Use of this command requires knowledge of the numeric enumeration value of the parameter. |Parameter number| Parameter value| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_SET_RELAY = 181			# Set a relay to a condition. |Relay number| Setting (1=on, 0=off, others possible depending on system hardware)| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_REPEAT_RELAY = 182		# Cycle a relay on and off for a desired number of cycles with a desired period. |Relay number| Cycle count| Cycle time (seconds, decimal)| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_REPEAT_SERVO = 184		# Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_FLIGHTTERMINATION = 185		# Terminate flight immediately |Flight termination activated if > 0.5| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_CHANGE_ALTITUDE = 186		# Set the vehicle to Loiter mode and change the altitude to specified value |Altitude| Frame of new altitude | Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_SET_ACTUATOR = 187		# Sets actuators (e.g. servos) to a desired value. |Actuator 1| Actuator 2| Actuator 3| Actuator 4| Actuator 5| Actuator 6| Index|
-uint16 VEHICLE_CMD_DO_LAND_START = 189			# Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|
-uint16 VEHICLE_CMD_DO_GO_AROUND = 191			# Mission command to safely abort an autonomous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_REPOSITION = 192			# Reposition to specific WGS84 GPS position. |Ground speed [m/s] |Bitmask |Loiter radius [m] for planes |Yaw	[deg] |Latitude	|Longitude |Altitude |
+uint16 VEHICLE_CMD_CUSTOM_0 = 0 # Test command.
+uint16 VEHICLE_CMD_CUSTOM_1 = 1 # Test command.
+uint16 VEHICLE_CMD_CUSTOM_2 = 2 # Test command.
+uint16 VEHICLE_CMD_NAV_WAYPOINT = 16 # Navigate to MISSION. |[s] (decimal) Hold time. (ignored by fixed wing, time to stay at MISSION for rotary wing)|[m] Acceptance radius (if the sphere with this radius is hit, the MISSION counts as reached)|0 to pass through the WP, if > 0 radius [m] to pass by WP. Positive value for clockwise orbit, negative value for counter-clockwise orbit. Allows trajectory control.|Desired yaw angle at MISSION (rotary wing)|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_NAV_LOITER_UNLIM = 17 # Loiter around this MISSION an unlimited amount of time. |Unused|Unused|[m] Radius around MISSION. If positive loiter clockwise, else counter-clockwise|Desired yaw angle.|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_NAV_LOITER_TURNS = 18 # Loiter around this MISSION for X turns. |Turns|Unused|Radius around MISSION [m]. If positive loiter clockwise, else counter-clockwise|Desired yaw angle.|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_NAV_LOITER_TIME = 19 # Loiter around this MISSION for time. |[s] Seconds (decimal)|Unused|Radius around MISSION [m]. If positive loiter clockwise, else counter-clockwise|Desired yaw angle.|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_NAV_RETURN_TO_LAUNCH = 20 # Return to launch location. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_NAV_LAND = 21 # Land at location. |Unused|Unused|Unused|Desired yaw angle.|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_NAV_TAKEOFF = 22 # Takeoff from ground / hand. |Unused (FW pitch from FW_TKO_PITCH_MIN)|Unused|Unused|[deg] [@range 0,360] Yaw angle in NED if yaw source available, ignored otherwise|Latitude (WGS-84)|Longitude (WGS-84)|[m] Altitude AMSL|
+uint16 VEHICLE_CMD_NAV_PRECLAND = 23 # Attempt a precision landing.
+uint16 VEHICLE_CMD_DO_ORBIT = 34 # Start orbiting on the circumference of a circle defined by the parameters. |[m] Radius|[m/s] Velocity|[@enum ORBIT_YAW_BEHAVIOUR] Yaw behaviour|Unused|Latitude/X|Longitude/Y|Altitude/Z|
+uint16 VEHICLE_CMD_DO_FIGUREEIGHT = 35 # Start flying on the outline of a figure eight defined by the parameters. |[m] Major radius|[m] Minor radius|[m/s] Velocity|Orientation|Latitude/X|Longitude/Y|Altitude/Z|
+uint16 VEHICLE_CMD_NAV_ROI = 80 # Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |[@enum VEHICLE_ROI] Region of interest mode.|MISSION index/ target ID.|ROI index (allows a vehicle to manage multiple ROI's)|Unused|x the location of the fixed ROI (see MAV_FRAME)|y|z|
+uint16 VEHICLE_CMD_NAV_PATHPLANNING = 81 # Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning|0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid|Unused|[deg] [@range 0, 360] Yaw angle at goal, in compass degrees|Latitude/X of goal|Longitude/Y of goal|Altitude/Z of goal|
+uint16 VEHICLE_CMD_NAV_VTOL_TAKEOFF = 84 # Takeoff from ground / hand and transition to fixed wing. |Minimum pitch (if airspeed sensor present), desired pitch without sensor|Unused|Unused|Yaw angle (if magnetometer present), ignored without magnetometer|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_NAV_VTOL_LAND = 85 # Transition to MC and land at location. |Unused|Unused|Unused|Desired yaw angle.|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_NAV_GUIDED_LIMITS = 90 # Set limits for external control. |[s] Timeout  - maximum time that external controller will be allowed to control vehicle. 0 means no timeout|[m] Absolute altitude min AMSL - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit|[m] Absolute altitude max - if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit|[m] Horizontal move limit (AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_NAV_GUIDED_MASTER = 91 # Set id of master controller. |System ID|Component ID|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_NAV_DELAY = 93 # Delay the next navigation command a number of seconds or until a specified time. |[s] Delay (decimal, -1 to enable time-of-day fields)|[h] hour (24h format, UTC, -1 to ignore)|minute (24h format, UTC, -1 to ignore)|second (24h format, UTC)|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_NAV_LAST = 95 # NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration.|Unused|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_CONDITION_DELAY = 112 # Delay mission state machine. |[s] Delay (decimal seconds)|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_CONDITION_CHANGE_ALT = 113 # Ascend/descend at rate. Delay mission state machine until desired altitude reached.|Descent / Ascend rate (m/s)|Unused|Unused|Unused|Unused|Unused|Finish Altitude|
+uint16 VEHICLE_CMD_CONDITION_DISTANCE = 114 # Delay mission state machine until within desired distance of next NAV point. |Distance [m]|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_CONDITION_YAW = 115 # Reach a certain target angle. |[deg] [@range 0,360] Target angle. 0 is north|[deg/s] Speed during yaw change|[@range -1,1] Direction: negative: counter clockwise, positive: clockwise |[ 1,0] Relative offset or absolute angle|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_CONDITION_LAST = 159 # NOP - This command is only used to mark the upper limit of the CONDITION commands in the enumeration. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_CONDITION_GATE = 4501 # Wait until passing a threshold. |2D coord mode: 0: Orthogonal to planned route|Altitude mode: 0: Ignore altitude|Unused|Unused|Lat|Lon|Alt|
+uint16 VEHICLE_CMD_DO_SET_MODE = 176 # Set system mode. |Mode, as defined by ENUM MAV_MODE|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_JUMP = 177 # Jump to the desired command in the mission list. Repeat this action only the specified number of times. |Sequence number|Repeat count|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_CHANGE_SPEED = 178 # Change speed and/or throttle set points. |[@enum SPEED_TYPE] Speed type (0=Airspeed, 1=Ground Speed)|Speed (m/s, -1 indicates no change)|[%] Throttle ( Percent, -1 indicates no change)|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_SET_HOME = 179 # Changes the home location either to the current location or a specified location. |Use current (1=use current location, 0=use specified location)|Unused|Unused|Unused|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_DO_SET_PARAMETER = 180 # Set a system parameter. Caution! Use of this command requires knowledge of the numeric enumeration value of the parameter. |Parameter number|Parameter value|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_SET_RELAY = 181 # Set a relay to a condition. |Relay number|Setting (1=on, 0=off, others possible depending on system hardware)|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_REPEAT_RELAY = 182 # Cycle a relay on and off for a desired number of cycles with a desired period. |Relay number|Cycle count|[s] Cycle time (decimal seconds)|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_REPEAT_SERVO = 184 # Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number|[us] PWM rate (1000 to 2000 typical)|Cycle count|[s] Cycle time|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_FLIGHTTERMINATION = 185 # Terminate flight immediately. |Flight termination activated if > 0.5|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_CHANGE_ALTITUDE = 186 # Set the vehicle to Loiter mode and change the altitude to specified value. |Altitude|Frame of new altitude|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_SET_ACTUATOR = 187 # Sets actuators (e.g. servos) to a desired value. |Actuator 1|Actuator 2|Actuator 3|Actuator 4|Actuator 5|Actuator 6|Index|
+uint16 VEHICLE_CMD_DO_LAND_START = 189 # Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Unused|Unused|Unused|Unused|Latitude|Longitude|Unused|
+uint16 VEHICLE_CMD_DO_GO_AROUND = 191 # Mission command to safely abort an autonomous landing. |[m] Altitude|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_REPOSITION = 192 # Reposition to specific WGS84 GPS position. |[m/s] Ground speed|Bitmask|[m] Loiter radius for planes|[deg] Yaw|Latitude|Longitude|Altitude|
 uint16 VEHICLE_CMD_DO_PAUSE_CONTINUE = 193
-uint16 VEHICLE_CMD_DO_SET_ROI_LOCATION = 195		# Sets the region of interest (ROI) to a location. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Empty| Empty| Empty| Empty| Latitude| Longitude| Altitude|
-uint16 VEHICLE_CMD_DO_SET_ROI_WPNEXT_OFFSET = 196 	# Sets the region of interest (ROI) to be toward next waypoint, with optional pitch/roll/yaw offset. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Empty| Empty| Empty| Empty| pitch offset from next waypoint| roll offset from next waypoint| yaw offset from next waypoint|
-uint16 VEHICLE_CMD_DO_SET_ROI_NONE = 197		# Cancels any previous ROI command returning the vehicle/sensors to default flight characteristics. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_CONTROL_VIDEO = 200		# Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_SET_ROI = 201			# Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|
+uint16 VEHICLE_CMD_DO_SET_ROI_LOCATION = 195 # Sets the region of interest (ROI) to a location. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Unused|Unused|Unused|Unused|Latitude|Longitude|Altitude|
+uint16 VEHICLE_CMD_DO_SET_ROI_WPNEXT_OFFSET = 196 # Sets the region of interest (ROI) to be toward next waypoint, with optional pitch/roll/yaw offset. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Unused|Unused|Unused|Unused|Pitch offset from next waypoint|Roll offset from next waypoint|Yaw offset from next waypoint|
+uint16 VEHICLE_CMD_DO_SET_ROI_NONE = 197 # Cancels any previous ROI command returning the vehicle/sensors to default flight characteristics. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_CONTROL_VIDEO = 200 # Control onboard camera system. |Camera ID (-1 for all)|Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw|Transmission mode: 0: video stream, >0: single images every n seconds (decimal seconds)|Recording: 0: disabled, 1: enabled compressed, 2: enabled raw|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_SET_ROI = 201 # Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |[@enum VEHICLE_ROI] Region of interest mode.|MISSION index/ target ID.|ROI index (allows a vehicle to manage multiple ROI's)|Unused|x the location of the fixed ROI (see MAV_FRAME)|y|z|
 uint16 VEHICLE_CMD_DO_DIGICAM_CONTROL=203
-uint16 VEHICLE_CMD_DO_MOUNT_CONFIGURE=204		# Mission command to configure a camera or antenna mount |Mount operation mode (see MAV_MOUNT_MODE enum)| stabilize roll? (1 = yes, 0 = no)| stabilize pitch? (1 = yes, 0 = no)| stabilize yaw? (1 = yes, 0 = no)| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_MOUNT_CONTROL=205			# Mission command to control a camera or antenna mount |pitch or lat in degrees, depending on mount mode.| roll or lon in degrees depending on mount mode| yaw or alt (in meters) depending on mount mode| reserved| reserved| reserved| MAV_MOUNT_MODE enum value|
-uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_DIST=206		# Mission command to set TRIG_DIST for this flight |Camera trigger distance (meters)| Shutter integration time (ms)| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_FENCE_ENABLE=207			# Mission command to enable the geofence |enable? (0=disable, 1=enable)| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_PARACHUTE=208			# Mission command to trigger a parachute |action (0=disable, 1=enable, 2=release, for some systems see PARACHUTE_ACTION enum, not in general message set.)| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_MOTOR_TEST=209			# motor test command |Instance (1, ...)| throttle type| throttle| timeout [s]| Motor count | Test order| Empty|
-uint16 VEHICLE_CMD_DO_INVERTED_FLIGHT=210		# Change to/from inverted flight |inverted (0=normal, 1=inverted)| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_GRIPPER = 211			# Command to operate a gripper
-uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_INTERVAL=214	# Mission command to set TRIG_INTERVAL for this flight |Camera trigger distance (meters)| Shutter integration time (ms)| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_MOUNT_CONTROL_QUAT=220		# Mission command to control a camera or antenna mount, using a quaternion as reference. |q1 - quaternion param #1, w (1 in null-rotation)| q2 - quaternion param #2, x (0 in null-rotation)| q3 - quaternion param #3, y (0 in null-rotation)| q4 - quaternion param #4, z (0 in null-rotation)| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_GUIDED_MASTER=221			# set id of master controller |System ID| Component ID| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_GUIDED_LIMITS=222			# set limits for external control |timeout - maximum time (in seconds) that external controller will be allowed to control vehicle. 0 means no timeout| absolute altitude min (in meters, AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue.  0 means no lower altitude limit| absolute altitude max (in meters)- if vehicle moves above this alt, the command will be aborted and the mission will continue.  0 means no upper altitude limit| horizontal move limit (in meters, AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_DO_LAST = 240			# NOP - This command is only used to mark the upper limit of the DO commands in the enumeration |Empty| Empty| Empty| Empty| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_PREFLIGHT_CALIBRATION = 241		# Trigger calibration. This command will be only accepted if in pre-flight mode. See mavlink spec MAV_CMD_PREFLIGHT_CALIBRATION
-uint16 PREFLIGHT_CALIBRATION_TEMPERATURE_CALIBRATION = 3# param value for VEHICLE_CMD_PREFLIGHT_CALIBRATION to start temperature calibration
-uint16 VEHICLE_CMD_PREFLIGHT_SET_SENSOR_OFFSETS = 242	# Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow| X axis offset (or generic dimension 1), in the sensor's raw units| Y axis offset (or generic dimension 2), in the sensor's raw units| Z axis offset (or generic dimension 3), in the sensor's raw units| Generic dimension 4, in the sensor's raw units| Generic dimension 5, in the sensor's raw units| Generic dimension 6, in the sensor's raw units|
-uint16 VEHICLE_CMD_PREFLIGHT_UAVCAN = 243		# UAVCAN configuration. If param 1 == 1 actuator mapping and direction assignment should be started
-uint16 VEHICLE_CMD_PREFLIGHT_STORAGE = 245		# Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM| Reserved| Reserved| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_PREFLIGHT_REBOOT_SHUTDOWN = 246	# Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer.| Reserved| Reserved| Empty| Empty| Empty|
-uint16 VEHICLE_CMD_OBLIQUE_SURVEY=260			# Mission command to set a Camera Auto Mount Pivoting Oblique Survey for this flight|Camera trigger distance (meters)| Shutter integration time (ms)| Camera minimum trigger interval| Number of positions| Roll| Pitch| Empty|
-uint16 VEHICLE_CMD_DO_SET_STANDARD_MODE=262		# Enable the specified standard MAVLink mode |MAV_STANDARD_MODE|
-uint16 VEHICLE_CMD_GIMBAL_DEVICE_INFORMATION = 283	# Command to ask information about a low level gimbal
+uint16 VEHICLE_CMD_DO_MOUNT_CONFIGURE=204 # Mission command to configure a camera or antenna mount. |[@enum MAV_MOUNT_MODE] Mount operation mode|Stabilize roll? (1 = yes, 0 = no)|Stabilize pitch? (1 = yes, 0 = no)|stabilize yaw? (1 = yes, 0 = no)|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_MOUNT_CONTROL=205 # Mission command to control a camera or antenna mount. |[deg] Pitch or lat, depending on mount mode.|[deg] Roll or lon depending on mount mode|[deg]/[m] Yaw or alt depending on mount mode|Unused|Unused|Unused|[@enum MAV_MOUNT_MODE]|
+uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_DIST=206 # Mission command to set TRIG_DIST for this flight. |[m] Camera trigger distance|[ms] Shutter integration time|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_FENCE_ENABLE=207 # Mission command to enable the geofence. |enable? (0=disable, 1=enable)|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_PARACHUTE=208 # Mission command to trigger a parachute. |action [@enum PARACHUTE_ACTION] (0=disable, 1=enable, 2=release, for some systems see [@enum PARACHUTE_ACTION], not in general message set.)|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_MOTOR_TEST=209 # Motor test command. |Instance (@range 1, )|throttle type|throttle|timeout [s]|Motor count|Test order|Unused|
+uint16 VEHICLE_CMD_DO_INVERTED_FLIGHT=210 # Change to/from inverted flight. |inverted (0=normal, 1=inverted)|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_GRIPPER = 211 # Command to operate a gripper.
+uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_INTERVAL=214 # Mission command to set TRIG_INTERVAL for this flight. |[m] Camera trigger distance|Shutter integration time (ms)|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_MOUNT_CONTROL_QUAT=220 # Mission command to control a camera or antenna mount, using a quaternion as reference. |q1 - quaternion param #1, w (1 in null-rotation)|q2 - quaternion param #2, x (0 in null-rotation)|q3 - quaternion param #3, y (0 in null-rotation)|q4 - quaternion param #4, z (0 in null-rotation)|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_GUIDED_MASTER=221 # Set id of master controller. |System ID|Component ID|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_GUIDED_LIMITS=222 # Set limits for external control. |[s] Timeout - maximum time that external controller will be allowed to control vehicle. 0 means no timeout|[m] Absolute altitude min(AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit|[m] Absolute altitude max - if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit|[m] Horizontal move limit (AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_DO_LAST = 240 # NOP - This command is only used to mark the upper limit of the DO commands in the enumeration. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_PREFLIGHT_CALIBRATION = 241 # Trigger calibration. This command will be only accepted if in pre-flight mode. See MAVLink spec MAV_CMD_PREFLIGHT_CALIBRATION.
+uint16 PREFLIGHT_CALIBRATION_TEMPERATURE_CALIBRATION = 3# Param value for VEHICLE_CMD_PREFLIGHT_CALIBRATION to start temperature calibration.
+uint16 VEHICLE_CMD_PREFLIGHT_SET_SENSOR_OFFSETS = 242 # Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow|X axis offset (or generic dimension 1), in the sensor's raw units|Y axis offset (or generic dimension 2), in the sensor's raw units|Z axis offset (or generic dimension 3), in the sensor's raw units|Generic dimension 4, in the sensor's raw units|Generic dimension 5, in the sensor's raw units|Generic dimension 6, in the sensor's raw units|
+uint16 VEHICLE_CMD_PREFLIGHT_UAVCAN = 243 # UAVCAN configuration. If param 1 == 1 actuator mapping and direction assignment should be started.
+uint16 VEHICLE_CMD_PREFLIGHT_STORAGE = 245 # Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM|Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_PREFLIGHT_REBOOT_SHUTDOWN = 246 # Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot.|0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer.|Unused|Unused|Unused|Unused|Unused|
+uint16 VEHICLE_CMD_OBLIQUE_SURVEY=260 # Mission command to set a Camera Auto Mount Pivoting Oblique Survey for this flight. |[m] Camera trigger distance|[ms] Shutter integration time|Camera minimum trigger interval|Number of positions|Roll|Pitch|Unused|
+uint16 VEHICLE_CMD_DO_SET_STANDARD_MODE=262 # Enable the specified standard MAVLink mode. |MAV_STANDARD_MODE|
+uint16 VEHICLE_CMD_GIMBAL_DEVICE_INFORMATION = 283 # Command to ask information about a low level gimbal.
 
-uint16 VEHICLE_CMD_MISSION_START = 300			# start running a mission |first_item: the first mission item to run| last_item:  the last mission item to run (after this item is run, the mission ends)|
-uint16 VEHICLE_CMD_ACTUATOR_TEST = 310			# Actuator testing command|value [-1,1]|timeout [s]|Empty|Empty|output function|
-uint16 VEHICLE_CMD_CONFIGURE_ACTUATOR = 311		# Actuator configuration command|configuration|Empty|Empty|Empty|output function|
-uint16 VEHICLE_CMD_COMPONENT_ARM_DISARM = 400		# Arms / Disarms a component |1 to arm, 0 to disarm
-uint16 VEHICLE_CMD_RUN_PREARM_CHECKS = 401      	# Instructs a target system to run pre-arm checks.
-uint16 VEHICLE_CMD_INJECT_FAILURE = 420			# Inject artificial failure for testing purposes
-uint16 VEHICLE_CMD_START_RX_PAIR = 500			# Starts receiver pairing |0:Spektrum| 0:Spektrum DSM2, 1:Spektrum DSMX|
-uint16 VEHICLE_CMD_REQUEST_MESSAGE = 512    		# Request to send a single instance of the specified message
-uint16 VEHICLE_CMD_REQUEST_CAMERA_INFORMATION = 521     # Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|
-uint16 VEHICLE_CMD_SET_CAMERA_MODE = 530		# Set camera capture mode (photo, video, etc.)
-uint16 VEHICLE_CMD_SET_CAMERA_ZOOM = 531		# Set camera zoom
+uint16 VEHICLE_CMD_MISSION_START = 300 # Start running a mission. |first_item: the first mission item to run|last_item: the last mission item to run (after this item is run, the mission ends)|
+uint16 VEHICLE_CMD_ACTUATOR_TEST = 310 # Actuator testing command. |[@range -1,1] value|[s] timeout|Unused|Unused|output function|
+uint16 VEHICLE_CMD_CONFIGURE_ACTUATOR = 311 # Actuator configuration command. |configuration|Unused|Unused|Unused|output function|
+uint16 VEHICLE_CMD_COMPONENT_ARM_DISARM = 400 # Arms / Disarms a component. |1 to arm, 0 to disarm.
+uint16 VEHICLE_CMD_RUN_PREARM_CHECKS = 401 # Instructs a target system to run pre-arm checks.
+uint16 VEHICLE_CMD_INJECT_FAILURE = 420 # Inject artificial failure for testing purposes.
+uint16 VEHICLE_CMD_START_RX_PAIR = 500 # Starts receiver pairing. |0:Spektrum|0:Spektrum DSM2, 1:Spektrum DSMX|
+uint16 VEHICLE_CMD_REQUEST_MESSAGE = 512 # Request to send a single instance of the specified message.
+uint16 VEHICLE_CMD_REQUEST_CAMERA_INFORMATION = 521 # Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities|Reserved (all remaining params)|Reserved (default:0)|Reserved (default:0)|Reserved (default:0)|Reserved (default:0)|Reserved (default:0)|
+uint16 VEHICLE_CMD_SET_CAMERA_MODE = 530 # Set camera capture mode (photo, video, etc.).
+uint16 VEHICLE_CMD_SET_CAMERA_ZOOM = 531 # Set camera zoom.
 uint16 VEHICLE_CMD_SET_CAMERA_FOCUS = 532
-uint16 VEHICLE_CMD_DO_GIMBAL_MANAGER_PITCHYAW = 1000 	# Setpoint to be sent to a gimbal manager to set a gimbal pitch and yaw
-uint16 VEHICLE_CMD_DO_GIMBAL_MANAGER_CONFIGURE = 1001 	# Gimbal configuration to set which sysid/compid is in primary and secondary control
-uint16 VEHICLE_CMD_IMAGE_START_CAPTURE = 2000   	# Start image capture sequence.
-uint16 VEHICLE_CMD_DO_TRIGGER_CONTROL = 2003		# Enable or disable on-board camera triggering system
-uint16 VEHICLE_CMD_VIDEO_START_CAPTURE = 2500   	# Start a video capture.
-uint16 VEHICLE_CMD_VIDEO_STOP_CAPTURE = 2501    	# Stop the current video capture.
-uint16 VEHICLE_CMD_LOGGING_START = 2510			# start streaming ULog data
-uint16 VEHICLE_CMD_LOGGING_STOP = 2511			# stop streaming ULog data
-uint16 VEHICLE_CMD_CONTROL_HIGH_LATENCY = 2600		# control starting/stopping transmitting data over the high latency link
-uint16 VEHICLE_CMD_DO_VTOL_TRANSITION = 3000    	# Command VTOL transition
-uint16 VEHICLE_CMD_ARM_AUTHORIZATION_REQUEST = 3001	# Request arm authorization
-uint16 VEHICLE_CMD_PAYLOAD_PREPARE_DEPLOY = 30001	# Prepare a payload deployment in the flight plan
-uint16 VEHICLE_CMD_PAYLOAD_CONTROL_DEPLOY = 30002	# Control a pre-programmed payload deployment
-uint16 VEHICLE_CMD_FIXED_MAG_CAL_YAW = 42006            # Magnetometer calibration based on provided known yaw. This allows for fast calibration using WMM field tables in the vehicle, given only the known yaw of the vehicle. If Latitude and longitude are both zero then use the current vehicle location.
-uint16 VEHICLE_CMD_DO_WINCH = 42600			# Command to operate winch.
+uint16 VEHICLE_CMD_DO_GIMBAL_MANAGER_PITCHYAW = 1000 # Setpoint to be sent to a gimbal manager to set a gimbal pitch and yaw.
+uint16 VEHICLE_CMD_DO_GIMBAL_MANAGER_CONFIGURE = 1001 # Gimbal configuration to set which sysid/compid is in primary and secondary control.
+uint16 VEHICLE_CMD_IMAGE_START_CAPTURE = 2000 # Start image capture sequence.
+uint16 VEHICLE_CMD_DO_TRIGGER_CONTROL = 2003 # Enable or disable on-board camera triggering system.
+uint16 VEHICLE_CMD_VIDEO_START_CAPTURE = 2500 # Start a video capture.
+uint16 VEHICLE_CMD_VIDEO_STOP_CAPTURE = 2501 # Stop the current video capture.
+uint16 VEHICLE_CMD_LOGGING_START = 2510 # Start streaming ULog data.
+uint16 VEHICLE_CMD_LOGGING_STOP = 2511 # Stop streaming ULog data.
+uint16 VEHICLE_CMD_CONTROL_HIGH_LATENCY = 2600 # Control starting/stopping transmitting data over the high latency link.
+uint16 VEHICLE_CMD_DO_VTOL_TRANSITION = 3000 # Command VTOL transition.
+uint16 VEHICLE_CMD_ARM_AUTHORIZATION_REQUEST = 3001 # Request arm authorization.
+uint16 VEHICLE_CMD_PAYLOAD_PREPARE_DEPLOY = 30001 # Prepare a payload deployment in the flight plan.
+uint16 VEHICLE_CMD_PAYLOAD_CONTROL_DEPLOY = 30002 # Control a pre-programmed payload deployment.
+uint16 VEHICLE_CMD_FIXED_MAG_CAL_YAW = 42006 # Magnetometer calibration based on provided known yaw. This allows for fast calibration using WMM field tables in the vehicle, given only the known yaw of the vehicle. If Latitude and longitude are both zero then use the current vehicle location.
+uint16 VEHICLE_CMD_DO_WINCH = 42600 # Command to operate winch.
 
-uint16 VEHICLE_CMD_EXTERNAL_POSITION_ESTIMATE = 43003 # external reset of estimator global position when deadreckoning
+uint16 VEHICLE_CMD_EXTERNAL_POSITION_ESTIMATE = 43003 # External reset of estimator global position when dead reckoning.
 uint16 VEHICLE_CMD_EXTERNAL_WIND_ESTIMATE = 43004
 
-# PX4 vehicle commands (beyond 16 bit mavlink commands)
-uint32 VEHICLE_CMD_PX4_INTERNAL_START    = 65537        # start of PX4 internal only vehicle commands (> UINT16_MAX)
-uint32 VEHICLE_CMD_SET_GPS_GLOBAL_ORIGIN = 100000       # Sets the GPS coordinates of the vehicle local origin (0,0,0) position. |Empty|Empty|Empty|Empty|Latitude|Longitude|Altitude|
-uint32 VEHICLE_CMD_SET_NAV_STATE = 100001               # Change mode by specifying nav_state directly. |nav_state|Empty|Empty|Empty|Empty|Empty|Empty|
+# PX4 vehicle commands (beyond 16 bit MAVLink commands).
+uint32 VEHICLE_CMD_PX4_INTERNAL_START = 65537 # Start of PX4 internal only vehicle commands (> UINT16_MAX).
+uint32 VEHICLE_CMD_SET_GPS_GLOBAL_ORIGIN = 100000 # Sets the GPS coordinates of the vehicle local origin (0,0,0) position. |Unused|Unused|Unused|Unused|Latitude (WGS-84)|Longitude (WGS-84)|[m] Altitude (AMSL from GNSS, positive above ground)|
+uint32 VEHICLE_CMD_SET_NAV_STATE = 100001 # Change mode by specifying nav_state directly. |nav_state|Unused|Unused|Unused|Unused|Unused|Unused|
 
-uint8 VEHICLE_MOUNT_MODE_RETRACT = 0			# Load and keep safe position (Roll,Pitch,Yaw) from permanent memory and stop stabilization |
-uint8 VEHICLE_MOUNT_MODE_NEUTRAL = 1			# Load and keep neutral position (Roll,Pitch,Yaw) from permanent memory. |
-uint8 VEHICLE_MOUNT_MODE_MAVLINK_TARGETING = 2		# Load neutral position and start MAVLink Roll,Pitch,Yaw control with stabilization |
-uint8 VEHICLE_MOUNT_MODE_RC_TARGETING = 3		# Load neutral position and start RC Roll,Pitch,Yaw control with stabilization |
-uint8 VEHICLE_MOUNT_MODE_GPS_POINT = 4			# Load neutral position and start to point to Lat,Lon,Alt |
-uint8 VEHICLE_MOUNT_MODE_ENUM_END = 5			#
+uint8 VEHICLE_MOUNT_MODE_RETRACT = 0 # Load and keep safe position (Roll,Pitch,Yaw) from permanent memory and stop stabilization.
+uint8 VEHICLE_MOUNT_MODE_NEUTRAL = 1 # Load and keep neutral position (Roll,Pitch,Yaw) from permanent memory.
+uint8 VEHICLE_MOUNT_MODE_MAVLINK_TARGETING = 2 # Load neutral position and start MAVLink Roll,Pitch,Yaw control with stabilization.
+uint8 VEHICLE_MOUNT_MODE_RC_TARGETING = 3 # Load neutral position and start RC Roll,Pitch,Yaw control with stabilization.
+uint8 VEHICLE_MOUNT_MODE_GPS_POINT = 4 # Load neutral position and start to point to Lat,Lon,Alt.
+uint8 VEHICLE_MOUNT_MODE_ENUM_END = 5 #
 
-uint8 VEHICLE_ROI_NONE = 0                         	# No region of interest |
-uint8 VEHICLE_ROI_WPNEXT = 1                       	# Point toward next MISSION |
-uint8 VEHICLE_ROI_WPINDEX = 2                     	# Point toward given MISSION |
-uint8 VEHICLE_ROI_LOCATION = 3                    	# Point toward fixed location |
-uint8 VEHICLE_ROI_TARGET = 4                       	# Point toward target
+uint8 VEHICLE_ROI_NONE = 0 # No region of interest.
+uint8 VEHICLE_ROI_WPNEXT = 1 # Point toward next MISSION.
+uint8 VEHICLE_ROI_WPINDEX = 2 # Point toward given MISSION.
+uint8 VEHICLE_ROI_LOCATION = 3 # Point toward fixed location.
+uint8 VEHICLE_ROI_TARGET = 4 # Point toward target.
 uint8 VEHICLE_ROI_ENUM_END = 5
 
 uint8 PARACHUTE_ACTION_DISABLE = 0
@@ -163,13 +163,13 @@ uint8 FAILURE_TYPE_SLOW = 5
 uint8 FAILURE_TYPE_DELAYED = 6
 uint8 FAILURE_TYPE_INTERMITTENT = 7
 
-# used as param1 in DO_CHANGE_SPEED command
+# Used as param1 in DO_CHANGE_SPEED command.
 uint8 SPEED_TYPE_AIRSPEED = 0
 uint8 SPEED_TYPE_GROUNDSPEED = 1
 uint8 SPEED_TYPE_CLIMB_SPEED = 2
 uint8 SPEED_TYPE_DESCEND_SPEED = 3
 
-# used as param3 in CMD_DO_ORBIT
+# Used as param3 in CMD_DO_ORBIT.
 uint8 ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TO_CIRCLE_CENTER = 0
 uint8 ORBIT_YAW_BEHAVIOUR_HOLD_INITIAL_HEADING = 1
 uint8 ORBIT_YAW_BEHAVIOUR_UNCONTROLLED = 2
@@ -177,29 +177,29 @@ uint8 ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TANGENT_TO_CIRCLE = 3
 uint8 ORBIT_YAW_BEHAVIOUR_RC_CONTROLLED = 4
 uint8 ORBIT_YAW_BEHAVIOUR_UNCHANGED = 5
 
-# used as param1 in ARM_DISARM command
+# Used as param1 in ARM_DISARM command.
 int8 ARMING_ACTION_DISARM = 0
 int8 ARMING_ACTION_ARM = 1
 
-# param2 in VEHICLE_CMD_DO_GRIPPER
+# param2 in VEHICLE_CMD_DO_GRIPPER.
 uint8 GRIPPER_ACTION_RELEASE = 0
 uint8 GRIPPER_ACTION_GRAB = 1
 
 uint8 ORB_QUEUE_LENGTH = 8
 
-float32 param1			# Parameter 1, as defined by MAVLink uint16 VEHICLE_CMD enum.
-float32 param2			# Parameter 2, as defined by MAVLink uint16 VEHICLE_CMD enum.
-float32 param3			# Parameter 3, as defined by MAVLink uint16 VEHICLE_CMD enum.
-float32 param4			# Parameter 4, as defined by MAVLink uint16 VEHICLE_CMD enum.
-float64 param5			# Parameter 5, as defined by MAVLink uint16 VEHICLE_CMD enum.
-float64 param6			# Parameter 6, as defined by MAVLink uint16 VEHICLE_CMD enum.
-float32 param7			# Parameter 7, as defined by MAVLink uint16 VEHICLE_CMD enum.
-uint32 command			# Command ID
-uint8 target_system		# System which should execute the command
-uint8 target_component		# Component which should execute the command, 0 for all components
-uint8 source_system		# System sending the command
-uint16 source_component	# Component / mode executor sending the command
-uint8 confirmation		# 0: First transmission of this command. 1-255: Confirmation transmissions (e.g. for kill command)
+float32 param1 # Parameter 1, as defined by MAVLink uint16 VEHICLE_CMD enum.
+float32 param2 # Parameter 2, as defined by MAVLink uint16 VEHICLE_CMD enum.
+float32 param3 # Parameter 3, as defined by MAVLink uint16 VEHICLE_CMD enum.
+float32 param4 # Parameter 4, as defined by MAVLink uint16 VEHICLE_CMD enum.
+float64 param5 # Parameter 5, as defined by MAVLink uint16 VEHICLE_CMD enum.
+float64 param6 # Parameter 6, as defined by MAVLink uint16 VEHICLE_CMD enum.
+float32 param7 # Parameter 7, as defined by MAVLink uint16 VEHICLE_CMD enum.
+uint32 command # Command ID.
+uint8 target_system # System which should execute the command.
+uint8 target_component # Component which should execute the command, 0 for all components.
+uint8 source_system # System sending the command.
+uint16 source_component # Component / mode executor sending the command.
+uint8 confirmation # 0: First transmission of this command. 1-255: Confirmation transmissions (e.g. for kill command).
 bool from_external
 
 uint16 COMPONENT_MODE_EXECUTOR_START = 1000

docs/uk/msg_docs/index.md

@@ -15,10 +15,18 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [ActuatorMotors](ActuatorMotors.md) — Motor control message
 - [ActuatorServos](ActuatorServos.md) — Servo control message
+- [AirspeedValidated](AirspeedValidated.md)
 - [ArmingCheckReply](ArmingCheckReply.md)
 - [ArmingCheckRequest](ArmingCheckRequest.md)
 - [BatteryStatus](BatteryStatus.md)
 - [ConfigOverrides](ConfigOverrides.md) — Configurable overrides by (external) modes or mode executors
+- [FixedWingLateralSetpoint](FixedWingLateralSetpoint.md) — Fixed Wing Lateral Setpoint message
+  Used by the fw_lateral_longitudinal_control module
+  At least one of course, airspeed_direction, or lateral_acceleration must be finite.
+- [FixedWingLongitudinalSetpoint](FixedWingLongitudinalSetpoint.md) — Fixed Wing Longitudinal Setpoint message
+  Used by the fw_lateral_longitudinal_control module
+  If pitch_direct and throttle_direct are not both finite, then the controller relies on altitude/height_rate and equivalent_airspeed to control vertical motion.
+  If both altitude and height_rate are NAN, the controller maintains the current altitude.
 - [GotoSetpoint](GotoSetpoint.md) — Position and (optional) heading setpoints with corresponding speed constraints
   Setpoints are intended as inputs to position and heading smoothers, respectively
   Setpoints do not need to be kinematically consistent
@@ -26,6 +34,11 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
   Unset optional setpoints are not controlled
   Unset optional constraints default to vehicle specifications
 - [HomePosition](HomePosition.md) — GPS home position in WGS84 coordinates.
+- [LateralControlConfiguration](LateralControlConfiguration.md) — Fixed Wing Lateral Control Configuration message
+  Used by the fw_lateral_longitudinal_control module to constrain FixedWingLateralSetpoint messages.
+- [LongitudinalControlConfiguration](LongitudinalControlConfiguration.md) — Fixed Wing Longitudinal Control Configuration message
+  Used by the fw_lateral_longitudinal_control module and TECS to constrain FixedWingLongitudinalSetpoint messages
+  and configure the resultant setpoints.
 - [ManualControlSetpoint](ManualControlSetpoint.md)
 - [ModeCompleted](ModeCompleted.md) — Mode completion result, published by an active mode.
   Можливі значення nav_state визначені в повідомленні VehicleStatus.
@@ -76,8 +89,6 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [Airspeed](Airspeed.md)
 
-- [AirspeedValidated](AirspeedValidated.md)
-
 - [AirspeedWind](AirspeedWind.md)
 
 - [AutotuneAttitudeControlStatus](AutotuneAttitudeControlStatus.md)
@@ -92,7 +103,7 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [CanInterfaceStatus](CanInterfaceStatus.md)
 
-- [CellularStatus](CellularStatus.md)
+- [CellularStatus](CellularStatus.md) — Cellular status
 
 - [CollisionConstraints](CollisionConstraints.md) — Local setpoint constraints in NED frame
   setting something to NaN means that no limit is provided
@@ -161,6 +172,14 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [FigureEightStatus](FigureEightStatus.md)
 
+- [FixedWingLateralGuidanceStatus](FixedWingLateralGuidanceStatus.md) — Fixed Wing Lateral Guidance Status message
+  Published by fw_pos_control module to report the resultant lateral setpoints and NPFG debug outputs
+
+- [FixedWingLateralStatus](FixedWingLateralStatus.md) — Fixed Wing Lateral Status message
+  Published by the fw_lateral_longitudinal_control module to report the resultant lateral setpoint
+
+- [FixedWingRunwayControl](FixedWingRunwayControl.md) — Auxiliary control fields for fixed-wing runway takeoff/landing
+
 - [FlightPhaseEstimation](FlightPhaseEstimation.md)
 
 - [FollowTarget](FollowTarget.md)
@@ -267,8 +286,6 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [NormalizedUnsignedSetpoint](NormalizedUnsignedSetpoint.md)
 
-- [NpfgStatus](NpfgStatus.md)
-
 - [ObstacleDistance](ObstacleDistance.md) — Obstacle distances in front of the sensor.
 
 - [OffboardControlMode](OffboardControlMode.md) — Off-board control mode
@@ -340,6 +357,8 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [RoverAttitudeStatus](RoverAttitudeStatus.md)
 
+- [RoverPositionSetpoint](RoverPositionSetpoint.md)
+
 - [RoverRateSetpoint](RoverRateSetpoint.md)
 
 - [RoverRateStatus](RoverRateStatus.md)
@@ -348,6 +367,8 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [RoverThrottleSetpoint](RoverThrottleSetpoint.md)
 
+- [RoverVelocitySetpoint](RoverVelocitySetpoint.md)
+
 - [RoverVelocityStatus](RoverVelocityStatus.md)
 
 - [Rpm](Rpm.md)
@@ -415,6 +436,9 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [TimesyncStatus](TimesyncStatus.md)
 
+- [TrajectorySetpoint6dof](TrajectorySetpoint6dof.md) — Trajectory setpoint in NED frame
+  Input to position controller.
+
 - [TransponderReport](TransponderReport.md)
 
 - [TuneControl](TuneControl.md) — This message is used to control the tunes, when the tune_id is set to CUSTOM
@@ -467,4 +491,8 @@ Graphs showing how these are used [can be found here](../middleware/uorb_graph.m
 
 - [YawEstimatorStatus](YawEstimatorStatus.md)
 
+- [AirspeedValidatedV0](AirspeedValidatedV0.md)
+
+- [VehicleAttitudeSetpointV0](VehicleAttitudeSetpointV0.md)
+
 - [VehicleStatusV0](VehicleStatusV0.md) — Encodes the system state of the vehicle published by commander