fly316/PX4-Autopilot
7
0
Fork 0
mirror of https://gitee.com/mirrors_PX4/PX4-Autopilot.git synced 2026-10-29 06:23:34 +08:00
Code Issues Packages Projects Releases Wiki Activity

docs: Update metadata (#25993)

Browse Source
This commit is contained in:
Hamish Willee
2025-11-26 15:05:05 +11:00
committed by GitHub
parent d9a66b11ac
commit 6eb2251ee5
17 changed files with 508 additions and 378 deletions
Download Patch File Download Diff File Expand all files Collapse all files
docs/en/config_rover/basic_setup.md
+1 -1
View File
@@ -88,7 +88,7 @@ Navigate to [Parameters](../advanced_config/parameters.md) in QGroundControl and
One approach to determine an appropriate value is:
1. From a standstill, give the rover full throttle until it reaches the maximum speed.
2. Disarm the rover and plot the `measured_speed_body_x` from [RoverVelocityStatus](../msg_docs/RoverVelocityStatus.md).
2. Disarm the rover and plot the `measured_speed_body_x` from [RoverSpeedStatus](../msg_docs/RoverSpeedStatus.md).
3. Divide the maximum speed by the time it took to reach it and set this as the value for [RO_ACCEL_LIM](#RO_ACCEL_LIM).
Some RC rovers have enough torque to lift up if the maximum acceleration is not limited.
docs/en/config_rover/position_tuning.md
+1 -4
View File
@@ -19,7 +19,6 @@ To tune the position controller configure the [parameters](../advanced_config/pa
$v*{max} = v*{full throttle} \cdot (1 - \theta\_{normalized} \cdot k) $
with
- $v_{max}:$ Maximum speed
- $v_{full throttle}:$ Speed at maximum throttle [RO_MAX_THR_SPEED](../advanced_config/parameter_reference.md#RO_MAX_THR_SPEED).
- $\theta_{normalized}:$ Course error (Course - bearing setpoint) normalized from $[0\degree, 180\degree]$ to $[0, 1]$
@@ -34,14 +33,13 @@ To tune the position controller configure the [parameters](../advanced_config/pa
::: tip
Plan a mission for the rover to drive a square and observe how it slows down when approaching a waypoint:
- If the rover decelerates too quickly decrease the [RO_DECEL_LIM](../advanced_config/parameter_reference.md#RO_DECEL_LIM) parameter, if it starts slowing down too early increase the parameter.
- If you observe a jerking motion as the rover slows down, decrease the [RO_JERK_LIM](../advanced_config/parameter_reference.md#RO_JERK_LIM) parameter otherwise increase it as much as possible as it can interfere with the tuning of [RO_DECEL_LIM](../advanced_config/parameter_reference.md#RO_DECEL_LIM).
These two parameters have to be tuned as a pair, repeat until you are satisfied with the behaviour.
:::
3. Plot the `adjusted_speed_body_x_setpoint` and `measured_speed_body_x` from the [RoverVelocityStatus](../msg_docs/RoverVelocityStatus.md) message over each other.
3. Plot the `adjusted_speed_body_x_setpoint` and `measured_speed_body_x` from the [RoverSpeedStatus](../msg_docs/RoverSpeedStatus.md) message over each other.
If the tracking of these setpoints is not satisfactory adjust the values for [RO_SPEED_P](../advanced_config/parameter_reference.md#RO_SPEED_P) and [RO_SPEED_I](../advanced_config/parameter_reference.md#RO_SPEED_I).
## Path Following
@@ -57,7 +55,6 @@ The following parameters are used to tune the algorithm:
Decreasing the parameter makes it more aggressive but can lead to oscillations.
To tune this:
1. Start with a value of 1 for [PP_LOOKAHD_GAIN](#PP_LOOKAHD_GAIN)
2. Put the rover in [Position mode](../flight_modes_rover/manual.md#position-mode) and while driving a straight line at approximately half the maximum speed observe its behaviour.
3. If the rover does not drive in a straight line, reduce the value of the parameter, if it oscillates around the path increase the value.
docs/en/config_rover/velocity_tuning.md
+1 -3
View File
@@ -23,11 +23,10 @@ To tune the velocity controller configure the following [parameters](../advanced
::: tip
To further tune this parameter:
1. Set [RO_SPEED_P](#RO_SPEED_P) and [RO_SPEED_I](#RO_SPEED_I) to zero.
This way the speed is only controlled by the feed-forward term, which makes it easier to tune.
2. Put the rover in [Position mode](../flight_modes_rover/manual.md#position-mode) and then move the left stick of your controller up and/or down and hold it at a few different levels for a couple of seconds each.
3. Disarm the rover and from the flight log plot the `adjusted_speed_body_x_setpoint` and the `measured_speed_body_x` from the [RoverVelocityStatus](../msg_docs/RoverVelocityStatus.md) message over each other.
3. Disarm the rover and from the flight log plot the `adjusted_speed_body_x_setpoint` and the `measured_speed_body_x` from the [RoverSpeedStatus](../msg_docs/RoverSpeedStatus.md) message over each other.
4. If the actual speed of the rover is higher than the speed setpoint, increase [RO_MAX_THR_SPEED](#RO_MAX_THR_SPEED).
If it is the other way around decrease the parameter and repeat until you are satisfied with the setpoint tracking.
@@ -64,7 +63,6 @@ These steps are only necessary if you are tuning/want to unlock the manual [Posi
Decreasing the parameter makes it more aggressive but can lead to oscillations.
To tune this:
1. Start with a value of 1 for [PP_LOOKAHD_GAIN](#PP_LOOKAHD_GAIN)
2. Put the rover in [Position mode](../flight_modes_rover/manual.md#position-mode) and while driving a straight line at approximately half the maximum speed observe its behaviour.
3. If the rover does not drive in a straight line, reduce the value of the parameter, if it oscillates around the path increase the value.