mirror of
https://gitee.com/mirrors_PX4/PX4-Autopilot.git
synced 2026-10-26 00:53:34 +08:00
Add driver for Univision UG-2864AMBAG01
git-svn-id: http://svn.code.sf.net/p/nuttx/code/trunk@5319 42af7a65-404d-4744-a932-0658087f49c3
This commit is contained in:
patacongo
@@ -183,12 +183,95 @@ config NOKIA6100_RGBORD
|
||||
endif
|
||||
|
||||
config LCD_UG9664HSWAG01
|
||||
bool "9664HSWAG01 OLED Display Module"
|
||||
bool "UG-9664HSWAG01 OLED Display Module"
|
||||
default n
|
||||
---help---
|
||||
ug-9664hswag01.c. OLED Display Module, UG-9664HSWAG01", Univision
|
||||
Technology Inc. Used with the LPC Xpresso and Embedded Artists
|
||||
base board.
|
||||
OLED Display Module, UG-9664HSWAG01, Univision Technology Inc. Used
|
||||
with the LPCXpresso and Embedded Artists base board.
|
||||
|
||||
Required LCD driver settings:
|
||||
LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
|
||||
LCD_MAXPOWER should be 1: 0=off, 1=on
|
||||
|
||||
Required SPI driver settings:
|
||||
SPI_CMDDATA - Include support for cmd/data selection.
|
||||
|
||||
if LCD_UG9664HSWAG01
|
||||
|
||||
config UG9664HSWAG01_SPIMODE
|
||||
int "UG-9664HSWAG01 SPI Mode"
|
||||
default 0
|
||||
---help---
|
||||
Controls the SPI mode
|
||||
|
||||
config UG9664HSWAG01_FREQUENCY
|
||||
int "UG-9664HSWAG01 SPI Frequency"
|
||||
default 3500000
|
||||
---help---
|
||||
Define to use a different bus frequency
|
||||
|
||||
config UG9664HSWAG01_NINTERFACES
|
||||
int "Number of UG-9664HSWAG01 Devices"
|
||||
default 1
|
||||
---help---
|
||||
Specifies the number of physical UG-9664HSWAG01 devices that will be
|
||||
supported. NOTE: At present, this must be undefined or defined to be 1.
|
||||
|
||||
config UG9664HSWAG01_POWER
|
||||
bool "Power control"
|
||||
default n
|
||||
---help---
|
||||
If the hardware supports a controllable OLED a power supply, this
|
||||
configuration should be defined. In this case the system must
|
||||
provide an interface ug_power().
|
||||
|
||||
endif
|
||||
|
||||
config LCD_UG2864AMBAG01
|
||||
bool "UG-2864AMBAG01 OLED Display Module"
|
||||
default n
|
||||
---help---
|
||||
OLED Display Module, UG-2864AMBAG01, Univision Technology Inc.
|
||||
|
||||
Required LCD driver settings:
|
||||
LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
|
||||
LCD_MAXPOWER should be 1: 0=off, 1=on
|
||||
|
||||
Required SPI driver settings:
|
||||
SPI_CMDDATA - Include support for cmd/data selection.
|
||||
|
||||
if LCD_UG2864AMBAG01
|
||||
|
||||
config UG2864AMBAG01_SPIMODE
|
||||
int "UG-2864AMBAG01 SPI Mode"
|
||||
default 3
|
||||
---help---
|
||||
Controls the SPI mode
|
||||
|
||||
config UG2864AMBAG01_FREQUENCY
|
||||
int "UG-2864AMBAG01 SPI Frequency"
|
||||
default 3500000
|
||||
---help---
|
||||
Define to use a different bus frequency
|
||||
|
||||
config UG2864AMBAG01_NINTERFACES
|
||||
int "Number of UG-2864AMBAG01 Devices"
|
||||
default 1
|
||||
---help---
|
||||
Specifies the number of physical UG-9664HSWAG01 devices that will be
|
||||
supported. NOTE: At present, this must be undefined or defined to be 1.
|
||||
|
||||
config UG2864AMBAG01_FRAMEBUFFER
|
||||
bool "UG-2864AMBAG01 Framebuffer"
|
||||
default y
|
||||
---help---
|
||||
If defined, accesses will be performed using an in-memory copy of the
|
||||
OLED's GRAM. This cost of this buffer is 128 * 64 / 8 = 1Kb.
|
||||
|
||||
If G2864AMBAG01_FRAMEBUFFER is not defined and the LCD is a LANDSCAPE
|
||||
mode, then a 128 byte buffer is still required.
|
||||
|
||||
endif
|
||||
|
||||
config LCD_SSD1289
|
||||
bool "LCD Based on SSD1289 Controller"
|
||||
|
||||
@@ -47,6 +47,10 @@ ifeq ($(CONFIG_LCD_NOKIA6100),y)
|
||||
CSRCS += nokia6100.c
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_LCD_UG2864AMBAG01),y)
|
||||
CSRCS += ug-2864ambag01.c
|
||||
endif
|
||||
|
||||
ifeq ($(CONFIG_LCD_UG9664HSWAG01),y)
|
||||
CSRCS += ug-9664hswag01.c
|
||||
endif
|
||||
|
||||
File diff suppressed because it is too large
Load Diff
@@ -73,8 +73,6 @@
|
||||
* CONFIG_UG9664HSWAG01_POWER
|
||||
* If the hardware supports a controllable OLED a power supply, this
|
||||
* configuration shold be defined. (See ug_power() below).
|
||||
* CONFIG_LCD_UGDEBUG - Enable detailed UG-9664HSWAG01 debug output
|
||||
* (CONFIG_DEBUG and CONFIG_VERBOSE must also be enabled).
|
||||
*
|
||||
* Required LCD driver settings:
|
||||
* CONFIG_LCD_UG9664HSWAG01 - Enable UG-9664HSWAG01 support
|
||||
@@ -119,11 +117,10 @@
|
||||
|
||||
#ifndef CONFIG_DEBUG
|
||||
# undef CONFIG_DEBUG_VERBOSE
|
||||
# undef CONFIG_DEBUG_GRAPHICS
|
||||
#endif
|
||||
|
||||
#ifndef CONFIG_DEBUG_VERBOSE
|
||||
# undef CONFIG_LCD_UGDEBUG
|
||||
# undef CONFIG_DEBUG_LCD
|
||||
#endif
|
||||
|
||||
/* Check contrast selection */
|
||||
@@ -198,10 +195,10 @@
|
||||
|
||||
/* Debug ******************************************************************************/
|
||||
|
||||
#ifdef CONFIG_LCD_UGDEBUG
|
||||
# define ugdbg(format, arg...) vdbg(format, ##arg)
|
||||
#ifdef CONFIG_DEBUG_LCD
|
||||
# define lcddbg(format, arg...) vdbg(format, ##arg)
|
||||
#else
|
||||
# define ugdbg(x...)
|
||||
# define lcddbg(x...)
|
||||
#endif
|
||||
|
||||
/**************************************************************************************
|
||||
@@ -997,7 +994,7 @@ FAR struct lcd_dev_s *ug_initialize(FAR struct spi_dev_s *spi, unsigned int devn
|
||||
|
||||
SPI_CMDDATA(spi, SPIDEV_DISPLAY, true);
|
||||
|
||||
/* Set the starting position for the run */
|
||||
/* Configure the device */
|
||||
|
||||
(void)SPI_SEND(spi, SSD1305_SETCOLL + 2); /* Set low column address */
|
||||
(void)SPI_SEND(spi, SSD1305_SETCOLH + 2); /* Set high column address */
|
||||
|
||||
Reference in New Issue
Block a user