diff --git a/boards/thepeach/k1/default.px4board b/boards/thepeach/k1/default.px4board new file mode 100644 index 0000000000..4d4ab00a94 --- /dev/null +++ b/boards/thepeach/k1/default.px4board @@ -0,0 +1,107 @@ +CONFIG_BOARD_TOOLCHAIN="arm-none-eabi" +CONFIG_BOARD_ARCHITECTURE="cortex-m4" +CONFIG_BOARD_CONSTRAINED_MEMORY=y +CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS3" +CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS1" +CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS2" +CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6" +CONFIG_DRIVERS_ADC_ADS1115=y +CONFIG_DRIVERS_ADC_BOARD_ADC=y +CONFIG_COMMON_BAROMETERS=y +CONFIG_DRIVERS_BATT_SMBUS=y +CONFIG_DRIVERS_CAMERA_CAPTURE=y +CONFIG_DRIVERS_CAMERA_TRIGGER=y +CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y +CONFIG_COMMON_DISTANCE_SENSOR=y +CONFIG_DRIVERS_DSHOT=y +CONFIG_DRIVERS_GPS=y +CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y +CONFIG_DRIVERS_IMU_INVENSENSE_ICM20948=y +CONFIG_DRIVERS_IMU_INVENSENSE_MPU9250=y +CONFIG_DRIVERS_IRLOCK=y +CONFIG_COMMON_LIGHT=y +CONFIG_COMMON_MAGNETOMETER=y +CONFIG_COMMON_OPTICAL_FLOW=y +CONFIG_DRIVERS_OSD=y +CONFIG_DRIVERS_PCA9685=y +CONFIG_DRIVERS_PCA9685_PWM_OUT=y +CONFIG_DRIVERS_POWER_MONITOR_INA226=y +CONFIG_DRIVERS_PWM_INPUT=y +CONFIG_DRIVERS_PWM_OUT=y +CONFIG_DRIVERS_PWM_OUT_SIM=y +CONFIG_DRIVERS_PX4IO=y +CONFIG_DRIVERS_ROBOCLAW=y +CONFIG_DRIVERS_RPM=y +CONFIG_DRIVERS_SMART_BATTERY_BATMON=y +CONFIG_COMMON_TELEMETRY=y +CONFIG_DRIVERS_TONE_ALARM=y +CONFIG_DRIVERS_UAVCAN=y +CONFIG_BOARD_UAVCAN_INTERFACES=1 +CONFIG_MODULES_AIRSPEED_SELECTOR=y +CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y +CONFIG_MODULES_BATTERY_STATUS=y +CONFIG_MODULES_CAMERA_FEEDBACK=y +CONFIG_MODULES_COMMANDER=y +CONFIG_MODULES_DATAMAN=y +CONFIG_MODULES_EKF2=y +CONFIG_MODULES_ESC_BATTERY=y +CONFIG_MODULES_EVENTS=y +CONFIG_MODULES_FLIGHT_MODE_MANAGER=y +CONFIG_MODULES_FW_ATT_CONTROL=y +CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y +CONFIG_MODULES_FW_POS_CONTROL_L1=y +CONFIG_MODULES_GYRO_CALIBRATION=y +CONFIG_MODULES_GYRO_FFT=y +CONFIG_MODULES_LAND_DETECTOR=y +CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y +CONFIG_MODULES_LOAD_MON=y +CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=y +CONFIG_MODULES_LOGGER=y +CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y +CONFIG_MODULES_MANUAL_CONTROL=y +CONFIG_MODULES_MAVLINK=y +CONFIG_MODULES_MC_ATT_CONTROL=y +CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y +CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y +CONFIG_MODULES_MC_POS_CONTROL=y +CONFIG_MODULES_MC_RATE_CONTROL=y +CONFIG_MODULES_CONTROL_ALLOCATOR=y +CONFIG_MODULES_NAVIGATOR=y +CONFIG_MODULES_RC_UPDATE=y +CONFIG_MODULES_ROVER_POS_CONTROL=y +CONFIG_MODULES_SENSORS=y +CONFIG_MODULES_SIH=y +CONFIG_MODULES_TEMPERATURE_COMPENSATION=y +CONFIG_MODULES_UUV_ATT_CONTROL=y +CONFIG_MODULES_UUV_POS_CONTROL=y +CONFIG_MODULES_GIMBAL=y +CONFIG_MODULES_VTOL_ATT_CONTROL=y +CONFIG_SYSTEMCMDS_BL_UPDATE=y +CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y +CONFIG_SYSTEMCMDS_DUMPFILE=y +CONFIG_SYSTEMCMDS_GPIO=y +CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y +CONFIG_SYSTEMCMDS_I2CDETECT=y +CONFIG_SYSTEMCMDS_LED_CONTROL=y +CONFIG_SYSTEMCMDS_MFT=y +CONFIG_SYSTEMCMDS_MIXER=y +CONFIG_SYSTEMCMDS_MOTOR_TEST=y +CONFIG_SYSTEMCMDS_MTD=y +CONFIG_SYSTEMCMDS_NSHTERM=y +CONFIG_SYSTEMCMDS_PARAM=y +CONFIG_SYSTEMCMDS_PERF=y +CONFIG_SYSTEMCMDS_PWM=y +CONFIG_SYSTEMCMDS_REBOOT=y +CONFIG_SYSTEMCMDS_REFLECT=y +CONFIG_SYSTEMCMDS_SD_BENCH=y +CONFIG_SYSTEMCMDS_SD_STRESS=y +CONFIG_SYSTEMCMDS_SERIAL_TEST=y +CONFIG_SYSTEMCMDS_SYSTEM_TIME=y +CONFIG_SYSTEMCMDS_TOP=y +CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y +CONFIG_SYSTEMCMDS_TUNE_CONTROL=y +CONFIG_SYSTEMCMDS_UORB=y +CONFIG_SYSTEMCMDS_USB_CONNECTED=y +CONFIG_SYSTEMCMDS_VER=y +CONFIG_SYSTEMCMDS_WORK_QUEUE=y +CONFIG_EXAMPLES_FAKE_GPS=y diff --git a/boards/thepeach/k1/extras/px4_io-v2_default.bin b/boards/thepeach/k1/extras/px4_io-v2_default.bin new file mode 100755 index 0000000000..25a00e2357 Binary files /dev/null and b/boards/thepeach/k1/extras/px4_io-v2_default.bin differ diff --git a/boards/thepeach/k1/extras/thepeach_k1_bootloader.bin b/boards/thepeach/k1/extras/thepeach_k1_bootloader.bin new file mode 100755 index 0000000000..33f6c9b57e Binary files /dev/null and b/boards/thepeach/k1/extras/thepeach_k1_bootloader.bin differ diff --git a/boards/thepeach/k1/firmware.prototype b/boards/thepeach/k1/firmware.prototype new file mode 100644 index 0000000000..24b74c7fbf --- /dev/null +++ b/boards/thepeach/k1/firmware.prototype @@ -0,0 +1,13 @@ +{ + "board_id": 212, + "magic": "PX4FWv1", + "description": "Firmware for the ThePeach K1 board", + "image": "", + "build_time": 0, + "summary": "ThePeach K1", + "version": "0.1", + "image_size": 0, + "image_maxsize": 2080768, + "git_identity": "", + "board_revision": 0 +} diff --git a/boards/thepeach/k1/init/rc.board_defaults b/boards/thepeach/k1/init/rc.board_defaults new file mode 100644 index 0000000000..f22fa838f4 --- /dev/null +++ b/boards/thepeach/k1/init/rc.board_defaults @@ -0,0 +1,7 @@ +#!/bin/sh +# +# board specific defaults +#------------------------------------------------------------------------------ + +param set-default BAT1_V_DIV 18.1 +param set-default BAT1_A_PER_V 36.367515152 diff --git a/boards/thepeach/k1/init/rc.board_sensors b/boards/thepeach/k1/init/rc.board_sensors new file mode 100644 index 0000000000..730efee6b4 --- /dev/null +++ b/boards/thepeach/k1/init/rc.board_sensors @@ -0,0 +1,11 @@ +#!/bin/sh +# +# Board specific sensors init +#------------------------------------------------------------------------------ +board_adc start + +# SPI1 +ms5611 -s -b 1 start + +icm20602 -s -b 1 -R 8 start +mpu9250 -s -b 1 -R 8 -M start diff --git a/boards/thepeach/k1/nuttx-config/include/board.h b/boards/thepeach/k1/nuttx-config/include/board.h new file mode 100644 index 0000000000..a6502ad8d2 --- /dev/null +++ b/boards/thepeach/k1/nuttx-config/include/board.h @@ -0,0 +1,271 @@ +/************************************************************************************ + * board.h + * include/arch/board/board.h + * + * Copyright (C) 2009, 2016 Gregory Nutt. All rights reserved. + * Authors: Gregory Nutt + * David Sidrane + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ************************************************************************************/ + +#ifndef __ARCH_BOARD_BOARD_H +#define __ARCH_BOARD_BOARD_H + +/************************************************************************************ + * Included Files + ************************************************************************************/ +#include "board_dma_map.h" + +#include +#ifndef __ASSEMBLY__ +# include +#endif + +#include + +/************************************************************************************ + * Definitions + ************************************************************************************/ + +/* Clocking *************************************************************************/ +/* The PX4FMUV2 uses a 24MHz crystal connected to the HSE. + * + * This is the "standard" configuration as set up by arch/arm/src/stm32f40xx_rcc.c: + * System Clock source : PLL (HSE) + * SYSCLK(Hz) : 168000000 Determined by PLL configuration + * HCLK(Hz) : 168000000 (STM32_RCC_CFGR_HPRE) + * AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE) + * APB1 Prescaler : 4 (STM32_RCC_CFGR_PPRE1) + * APB2 Prescaler : 2 (STM32_RCC_CFGR_PPRE2) + * HSE Frequency(Hz) : 24000000 (STM32_BOARD_XTAL) + * PLLM : 24 (STM32_PLLCFG_PLLM) + * PLLN : 336 (STM32_PLLCFG_PLLN) + * PLLP : 2 (STM32_PLLCFG_PLLP) + * PLLQ : 7 (STM32_PLLCFG_PPQ) + * Main regulator output voltage : Scale1 mode Needed for high speed SYSCLK + * Flash Latency(WS) : 5 + * Prefetch Buffer : OFF + * Instruction cache : ON + * Data cache : ON + * Require 48MHz for USB OTG FS, : Enabled + * SDIO and RNG clock + */ + +/* HSI - 16 MHz RC factory-trimmed + * LSI - 32 KHz RC + * HSE - On-board crystal frequency is 24MHz + * LSE - not installed + */ + +#define STM32_BOARD_XTAL 24000000ul + +#define STM32_HSI_FREQUENCY 16000000ul +#define STM32_LSI_FREQUENCY 32000 +#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL +//#define STM32_LSE_FREQUENCY 32768 + +/* Main PLL Configuration. + * + * PLL source is HSE + * PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN + * = (25,000,000 / 25) * 336 + * = 336,000,000 + * SYSCLK = PLL_VCO / PLLP + * = 336,000,000 / 2 = 168,000,000 + * USB OTG FS, SDIO and RNG Clock + * = PLL_VCO / PLLQ + * = 48,000,000 + */ + +#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(24) +#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336) +#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2 +#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7) + +#define STM32_SYSCLK_FREQUENCY 168000000ul + +/* AHB clock (HCLK) is SYSCLK (168MHz) */ + +#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */ +#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY +#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */ + +/* APB1 clock (PCLK1) is HCLK/4 (42MHz) */ + +#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */ +#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4) + +/* Timers driven from APB1 will be twice PCLK1 */ + +#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY) + +/* APB2 clock (PCLK2) is HCLK/2 (84MHz) */ + +#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */ +#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2) + +/* Timers driven from APB2 will be twice PCLK2 */ + +#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY) + +/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx + * otherwise frequency is 2xAPBx. + * Note: TIM1,8-11 are on APB2, others on APB1 + */ + +#define BOARD_TIM1_FREQUENCY STM32_APB2_TIM1_CLKIN +#define BOARD_TIM2_FREQUENCY STM32_APB1_TIM2_CLKIN +#define BOARD_TIM3_FREQUENCY STM32_APB1_TIM3_CLKIN +#define BOARD_TIM4_FREQUENCY STM32_APB1_TIM4_CLKIN +#define BOARD_TIM5_FREQUENCY STM32_APB1_TIM5_CLKIN +#define BOARD_TIM6_FREQUENCY STM32_APB1_TIM6_CLKIN +#define BOARD_TIM7_FREQUENCY STM32_APB1_TIM7_CLKIN +#define BOARD_TIM8_FREQUENCY STM32_APB2_TIM8_CLKIN +#define BOARD_TIM9_FREQUENCY STM32_APB2_TIM9_CLKIN +#define BOARD_TIM10_FREQUENCY STM32_APB2_TIM10_CLKIN +#define BOARD_TIM11_FREQUENCY STM32_APB2_TIM11_CLKIN +#define BOARD_TIM12_FREQUENCY STM32_APB1_TIM12_CLKIN +#define BOARD_TIM13_FREQUENCY STM32_APB1_TIM13_CLKIN +#define BOARD_TIM14_FREQUENCY STM32_APB1_TIM14_CLKIN + +/* SDIO dividers. Note that slower clocking is required when DMA is disabled + * in order to avoid RX overrun/TX underrun errors due to delayed responses + * to service FIFOs in interrupt driven mode. These values have not been + * tuned!!! + * + * SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(118+2)=400 KHz + */ + +#define SDIO_INIT_CLKDIV (118 << SDIO_CLKCR_CLKDIV_SHIFT) + +/* DMA ON: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(1+2)=16 MHz + * DMA OFF: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(2+2)=12 MHz + */ + +#ifdef CONFIG_STM32_SDIO_DMA +# define SDIO_MMCXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) +#else +# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) +#endif + +/* DMA ON: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(1+2)=16 MHz + * DMA OFF: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(2+2)=12 MHz + */ + +#ifdef CONFIG_STM32_SDIO_DMA +# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) +#else +# define SDIO_SDXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) +#endif + +/* Alternate function pin selections ************************************************/ + +/* UARTs */ + +#define GPIO_USART1_RX GPIO_USART1_RX_1 /* Console in from IO */ +#define GPIO_USART1_TX 0 /* USART1 is RX-only */ + +#define GPIO_USART2_RX GPIO_USART2_RX_2 +#define GPIO_USART2_TX GPIO_USART2_TX_2 +#define GPIO_USART2_RTS GPIO_USART2_RTS_2 +#define GPIO_USART2_CTS GPIO_USART2_CTS_2 + +#define GPIO_USART3_RX GPIO_USART3_RX_3 +#define GPIO_USART3_TX GPIO_USART3_TX_3 +#define GPIO_USART3_RTS GPIO_USART3_RTS_2 +#define GPIO_USART3_CTS GPIO_USART3_CTS_2 + +#define GPIO_UART4_RX GPIO_UART4_RX_1 +#define GPIO_UART4_TX GPIO_UART4_TX_1 + +#define GPIO_USART6_RX GPIO_USART6_RX_1 +#define GPIO_USART6_TX GPIO_USART6_TX_1 + +#define GPIO_UART7_RX GPIO_UART7_RX_1 +#define GPIO_UART7_TX GPIO_UART7_TX_1 + +/* UART8 has no alternate pin config */ + +/* CAN + * + * CAN1 is routed to the onboard transceiver. + */ + +#define GPIO_CAN1_RX GPIO_CAN1_RX_3 +#define GPIO_CAN1_TX GPIO_CAN1_TX_3 + +/* I2C + * + * The optional _GPIO configurations allow the I2C driver to manually + * reset the bus to clear stuck slaves. They match the pin configuration, + * but are normally-high GPIOs. + */ + +#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2 +#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2 +#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN8) +#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9) + +#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1 +#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1 +#define GPIO_I2C2_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN10) +#define GPIO_I2C2_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN11) + +/* SPI + * + * There are sensors on SPI1, and SPI2 is connected to the FRAM. + */ + +#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 +#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 +#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 + +#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 +#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 +#define GPIO_SPI2_SCK GPIO_SPI2_SCK_2 + +#define GPIO_SPI4_MISO GPIO_SPI4_MISO_1 +#define GPIO_SPI4_MOSI GPIO_SPI4_MOSI_1 +#define GPIO_SPI4_SCK GPIO_SPI4_SCK_1 + + +#endif /* __ARCH_BOARD_BOARD_H */ diff --git a/boards/thepeach/k1/nuttx-config/include/board_dma_map.h b/boards/thepeach/k1/nuttx-config/include/board_dma_map.h new file mode 100644 index 0000000000..96a4c81517 --- /dev/null +++ b/boards/thepeach/k1/nuttx-config/include/board_dma_map.h @@ -0,0 +1,93 @@ +/**************************************************************************** + * + * Copyright (c) 2020 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#pragma once + +/* +| DMA1 | Stream 0 | Stream 1 | Stream 2 | Stream 3 | Stream 4 | Stream 5 | Stream 6 | Stream 7 | +|------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------| +| Channel 0 | SPI3_RX_1 | - | SPI3_RX_2 | SPI2_RX | SPI2_TX | SPI3_TX_1 | - | SPI3_TX_2 | +| Channel 1 | I2C1_RX | - | TIM7_UP_1 | - | TIM7_UP_2 | I2C1_RX_1 | I2C1_TX | I2C1_TX_1 | +| Channel 2 | TIM4_CH1 | - | I2C4_RX | TIM4_CH2 | - | I2C4_RX | TIM4_UP | TIM4_CH3 | +| Channel 3 | - | TIM2_UP_1 | I2C3_RX_1 | I2C2_EXT_RX | I2C3_TX | TIM2_CH1 | TIM2_CH2 | TIM2_UP_2 | +| | | TIM2_CH3 | | | | | TIM2_CH4_1 | TIM2_CH4_2 | +| Channel 4 | UART5_RX | USART3_RX | UART4_RX | USART3_TX_1 | UART4_TX | USART2_RX | USART2_TX | UART5_TX | +| Channel 5 | UART8_TX | UART7_TX | TIM3_CH4 | UART7_RX | TIM3_CH1 | TIM3_CH2 | UART8_RX | TIM3_CH3 | +| | | | TIM3_UP | | TIM3_TRIG | | | | +| Channel 6 | TIM5_CH3 | TIM5_CH4_1 | TIM5_CH1 | TIM5_CH4_2 | TIM5_CH2 | - | TIM5_UP_2 | - | +| | TIM5_UP_1 | TIM5_TRIG_1 | | TIM5_TRIG_2 | | | | | +| Channel 7 | - | TIM6_UP | I2C2_RX | I2C2_RX_1 | USART3_TX_2 | DAC1 | DAC2 | I2C2_TX | +| | | | | | | | | | +| Usage | | USART3_RX | UART4_RX | UART7_RX | | USART2_RX | TIM4_UP | | + + +| DMA2 | Stream 0 | Stream 1 | Stream 2 | Stream 3 | Stream 4 | Stream 5 | Stream 6 | Stream 7 | +|------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------| +| Channel 0 | ADC1_1 | SAI1_A | TIM8_CH1_1 | SAI1_A_1 | ADC1_2 | SAI1_B_1 | TIM1_CH1_1 | - | +| | | | TIM8_CH2_1 | | | | TIM1_CH2_1 | | +| | | | TIM8_CH3_1 | | | | TIM1_CH3_1 | | +| Channel 1 | - | DCMI_1 | ADC2_1 | ADC2_2 | SAI1_B | SPI6_TX | SPI6_RX | DCMI_2 | +| Channel 2 | ADC3_1 | ADC3_2 | - | SPI5_RX_1 | SPI5_TX_1 | CRYP_OUT | CRYP_IN | HASH_IN | +| Channel 3 | SPI1_RX_1 | - | SPI1_RX_2 | SPI1_TX_1 | - | SPI1_TX_2 | - | QUADSPI | +| Channel 4 | SPI4_RX_1 | SPI4_TX_1 | USART1_RX_1 | SDIO | - | USART1_RX_2 | SDIO | USART1_TX | +| Channel 5 | - | USART6_RX_1 | USART6_RX_2 | SPI4_RX_2 | SPI4_TX_2 | - | USART6_TX_1 | USART6_TX_2 | +| Channel 6 | TIM1_TRIG_1 | TIM1_CH1_2 | TIM1_CH2_2 | TIM1_CH1 | TIM1_CH4 | TIM1_UP | TIM1_CH3_2 | - | +| | | | | | TIM1_TRIG_2 | | | | +| | | | | | TIM1_COM | | | | +| Channel 7 | - | TIM8_UP | TIM8_CH1_2 | TIM8_CH2_2 | TIM8_CH3_2 | SPI5_RX_2 | SPI5_TX_2 | TIM8_CH4 | +| | | | | | | | | TIM8_TRIG | +| | | | | | | | | TIM8_COM | +| | | | | | | | | | +| Usage | | USART6_RX_1 | SPI1_RX_2 | SPI1_TX_1 | | TIM1_UP | SDIO | USART6_TX_2 | + */ + +// DMA1 Channel/Stream Selections +//--------------------------------------------//---------------------------//---------------- +// DMAMAP_USART3_RX // DMA1, Stream 1, Channel 4 +// DMAMAP_UART4_RX // DMA1, Stream 2, Channel 4 +// DMAMAP_UART7_RX // DMA1, Stream 3, Channel 5 +// AVAILABLE // DMA1, Stream 4 +// DMAMAP_USART2_RX // DMA1, Stream 5, Channel 4 +// DMAMAP_TIM4_UP // DMA1, Stream 6, Channel 2 (DSHOT) + + +// DMA2 Channel/Stream Selections +//--------------------------------------------//---------------------------//---------------- +// AVAILABLE // DMA2, Stream 0 +#define DMAMAP_USART6_RX DMAMAP_USART6_RX_1 // DMA2, Stream 1, Channel 4 (PX4IO RX) +#define DMACHAN_SPI1_RX DMAMAP_SPI1_RX_2 // DMA2, Stream 2, Channel 3 (SPI1 sensors RX) +#define DMACHAN_SPI1_TX DMAMAP_SPI1_TX_1 // DMA2, Stream 3, Channel 3 (SPI1 sensors TX) +// AVAILABLE // DMA2, Stream 4 +// DMAMAP_TIM1_UP // DMA2, Stream 5, Channel 6 (DSHOT) +#define DMAMAP_SDIO DMAMAP_SDIO_2 // DMA2, Stream 6, Channel 4 +#define DMAMAP_USART6_TX DMAMAP_USART6_TX_2 // DMA2, Stream 7, Channel 5 (PX4IO TX) diff --git a/boards/thepeach/k1/nuttx-config/nsh/defconfig b/boards/thepeach/k1/nuttx-config/nsh/defconfig new file mode 100644 index 0000000000..e087c61fcd --- /dev/null +++ b/boards/thepeach/k1/nuttx-config/nsh/defconfig @@ -0,0 +1,230 @@ +# +# This file is autogenerated: PLEASE DO NOT EDIT IT. +# +# You can use "make menuconfig" to make any modifications to the installed .config file. +# You can then do "make savedefconfig" to generate a new defconfig file that includes your +# modifications. +# +# CONFIG_DISABLE_ENVIRON is not set +# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set +# CONFIG_MMCSD_HAVE_CARDDETECT is not set +# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set +# CONFIG_MMCSD_MMCSUPPORT is not set +# CONFIG_MMCSD_SPI is not set +# CONFIG_NSH_DISABLEBG is not set +# CONFIG_NSH_DISABLESCRIPT is not set +# CONFIG_NSH_DISABLE_DF is not set +# CONFIG_NSH_DISABLE_EXEC is not set +# CONFIG_NSH_DISABLE_EXIT is not set +# CONFIG_NSH_DISABLE_GET is not set +# CONFIG_NSH_DISABLE_ITEF is not set +# CONFIG_NSH_DISABLE_LOOPS is not set +# CONFIG_NSH_DISABLE_MKFATFS is not set +# CONFIG_NSH_DISABLE_SEMICOLON is not set +# CONFIG_NSH_DISABLE_TIME is not set +# CONFIG_STM32_CCMEXCLUDE is not set +CONFIG_ARCH="arm" +CONFIG_ARCH_BOARD_CUSTOM=y +CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/thepeach/k1/nuttx-config" +CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y +CONFIG_ARCH_BOARD_CUSTOM_NAME="px4" +CONFIG_ARCH_CHIP="stm32" +CONFIG_ARCH_CHIP_STM32=y +CONFIG_ARCH_CHIP_STM32F427V=y +CONFIG_ARCH_INTERRUPTSTACK=512 +CONFIG_ARCH_STACKDUMP=y +CONFIG_ARMV7M_MEMCPY=y +CONFIG_ARMV7M_USEBASEPRI=y +CONFIG_ARM_MPU_EARLY_RESET=y +CONFIG_BOARDCTL_RESET=y +CONFIG_BOARD_CRASHDUMP=y +CONFIG_BOARD_LOOPSPERMSEC=16717 +CONFIG_BOARD_RESET_ON_ASSERT=2 +CONFIG_BUILTIN=y +CONFIG_C99_BOOL8=y +CONFIG_CDCACM=y +CONFIG_CDCACM_IFLOWCONTROL=y +CONFIG_CDCACM_PRODUCTID=0x0001 +CONFIG_CDCACM_PRODUCTSTR="FCC-K1" +CONFIG_CDCACM_RXBUFSIZE=600 +CONFIG_CDCACM_TXBUFSIZE=2000 +CONFIG_CDCACM_VENDORID=0x35a7 +CONFIG_CDCACM_VENDORSTR="ThePeach" +CONFIG_DEBUG_FULLOPT=y +CONFIG_DEBUG_HARDFAULT_ALERT=y +CONFIG_DEBUG_SYMBOLS=y +CONFIG_DEFAULT_SMALL=y +CONFIG_DEV_FIFO_SIZE=0 +CONFIG_DEV_PIPE_MAXSIZE=1024 +CONFIG_DEV_PIPE_SIZE=70 +CONFIG_DISABLE_MQUEUE=y +CONFIG_EXAMPLES_CALIB_UDELAY=y +CONFIG_FAT_DMAMEMORY=y +CONFIG_FAT_LCNAMES=y +CONFIG_FAT_LFN=y +CONFIG_FAT_LFN_ALIAS_HASH=y +CONFIG_FDCLONE_STDIO=y +CONFIG_FS_BINFS=y +CONFIG_FS_CROMFS=y +CONFIG_FS_FAT=y +CONFIG_FS_FATTIME=y +CONFIG_FS_PROCFS=y +CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y +CONFIG_FS_PROCFS_REGISTER=y +CONFIG_FS_ROMFS=y +CONFIG_GRAN=y +CONFIG_GRAN_INTR=y +CONFIG_HAVE_CXX=y +CONFIG_HAVE_CXXINITIALIZE=y +CONFIG_I2C=y +CONFIG_I2C_RESET=y +CONFIG_IDLETHREAD_STACKSIZE=750 +CONFIG_LIBC_LONG_LONG=y +CONFIG_LIBC_STRERROR=y +CONFIG_MEMSET_64BIT=y +CONFIG_MEMSET_OPTSPEED=y +CONFIG_MMCSD=y +CONFIG_MMCSD_SDIO=y +CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y +CONFIG_MM_REGIONS=2 +CONFIG_MTD=y +CONFIG_MTD_BYTE_WRITE=y +CONFIG_MTD_PARTITION=y +CONFIG_MTD_RAMTRON=y +CONFIG_NAME_MAX=40 +CONFIG_NSH_ARCHINIT=y +CONFIG_NSH_ARGCAT=y +CONFIG_NSH_BUILTIN_APPS=y +CONFIG_NSH_CMDPARMS=y +CONFIG_NSH_CROMFSETC=y +CONFIG_NSH_DISABLE_IFCONFIG=y +CONFIG_NSH_DISABLE_IFUPDOWN=y +CONFIG_NSH_DISABLE_TELNETD=y +CONFIG_NSH_LINELEN=128 +CONFIG_NSH_MAXARGUMENTS=15 +CONFIG_NSH_NESTDEPTH=8 +CONFIG_NSH_QUOTE=y +CONFIG_NSH_ROMFSETC=y +CONFIG_NSH_ROMFSSECTSIZE=128 +CONFIG_NSH_STRERROR=y +CONFIG_NSH_VARS=y +CONFIG_PIPES=y +CONFIG_PREALLOC_TIMERS=50 +CONFIG_PRIORITY_INHERITANCE=y +CONFIG_PTHREAD_MUTEX_ROBUST=y +CONFIG_PTHREAD_STACK_MIN=512 +CONFIG_RAMTRON_SETSPEED=y +CONFIG_RAM_SIZE=262144 +CONFIG_RAM_START=0x20000000 +CONFIG_RAW_BINARY=y +CONFIG_RTC_DATETIME=y +CONFIG_SCHED_ATEXIT=y +CONFIG_SCHED_HPWORK=y +CONFIG_SCHED_HPWORKPRIORITY=249 +CONFIG_SCHED_HPWORKSTACKSIZE=1280 +CONFIG_SCHED_INSTRUMENTATION=y +CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y +CONFIG_SCHED_LPWORK=y +CONFIG_SCHED_LPWORKPRIORITY=50 +CONFIG_SCHED_LPWORKSTACKSIZE=1632 +CONFIG_SCHED_WAITPID=y +CONFIG_SDCLONE_DISABLE=y +CONFIG_SDIO_BLOCKSETUP=y +CONFIG_SEM_PREALLOCHOLDERS=32 +CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y +CONFIG_SERIAL_TERMIOS=y +CONFIG_SIG_DEFAULT=y +CONFIG_SIG_SIGALRM_ACTION=y +CONFIG_SIG_SIGUSR1_ACTION=y +CONFIG_SIG_SIGUSR2_ACTION=y +CONFIG_SIG_SIGWORK=4 +CONFIG_STACK_COLORATION=y +CONFIG_START_DAY=30 +CONFIG_START_MONTH=11 +CONFIG_STDIO_BUFFER_SIZE=32 +CONFIG_STM32_ADC1=y +CONFIG_STM32_BBSRAM=y +CONFIG_STM32_BBSRAM_FILES=5 +CONFIG_STM32_BKPSRAM=y +CONFIG_STM32_CCMDATARAM=y +CONFIG_STM32_DISABLE_IDLE_SLEEP_DURING_DEBUG=y +CONFIG_STM32_DMA1=y +CONFIG_STM32_DMA2=y +CONFIG_STM32_FLASH_CONFIG_I=y +CONFIG_STM32_FLOWCONTROL_BROKEN=y +CONFIG_STM32_I2C1=y +CONFIG_STM32_I2C2=y +CONFIG_STM32_I2CTIMEOMS=10 +CONFIG_STM32_I2CTIMEOTICKS=10 +CONFIG_STM32_JTAG_SW_ENABLE=y +CONFIG_STM32_OTGFS=y +CONFIG_STM32_PWR=y +CONFIG_STM32_RTC=y +CONFIG_STM32_RTC_HSECLOCK=y +CONFIG_STM32_RTC_MAGIC=0xfacefeee +CONFIG_STM32_RTC_MAGIC_REG=1 +CONFIG_STM32_RTC_MAGIC_TIME_SET=0xfacefeef +CONFIG_STM32_SAVE_CRASHDUMP=y +CONFIG_STM32_SDIO=y +CONFIG_STM32_SDIO_CARD=y +CONFIG_STM32_SERIALBRK_BSDCOMPAT=y +CONFIG_STM32_SERIAL_DISABLE_REORDERING=y +CONFIG_STM32_SPI1=y +CONFIG_STM32_SPI1_DMA=y +CONFIG_STM32_SPI1_DMA_BUFFER=512 +CONFIG_STM32_SPI2=y +CONFIG_STM32_SPI_DMA=y +CONFIG_STM32_SPI_DMATHRESHOLD=8 +CONFIG_STM32_TIM10=y +CONFIG_STM32_TIM11=y +CONFIG_STM32_TIM3=y +CONFIG_STM32_TIM9=y +CONFIG_STM32_UART4=y +CONFIG_STM32_UART7=y +CONFIG_STM32_UART8=y +CONFIG_STM32_USART1=y +CONFIG_STM32_USART2=y +CONFIG_STM32_USART3=y +CONFIG_STM32_USART6=y +CONFIG_STM32_USART_BREAKS=y +CONFIG_STM32_USART_SINGLEWIRE=y +CONFIG_STM32_WWDG=y +CONFIG_SYSTEM_CDCACM=y +CONFIG_SYSTEM_NSH=y +CONFIG_TASK_NAME_SIZE=24 +CONFIG_UART4_BAUD=57600 +CONFIG_UART4_RXBUFSIZE=300 +CONFIG_UART4_RXDMA=y +CONFIG_UART4_TXBUFSIZE=300 +CONFIG_UART7_BAUD=57600 +CONFIG_UART7_RXBUFSIZE=300 +CONFIG_UART7_RXDMA=y +CONFIG_UART7_SERIAL_CONSOLE=y +CONFIG_UART7_TXBUFSIZE=300 +CONFIG_UART8_BAUD=57600 +CONFIG_UART8_RXBUFSIZE=300 +CONFIG_UART8_TXBUFSIZE=300 +CONFIG_USART1_RXBUFSIZE=128 +CONFIG_USART1_TXBUFSIZE=32 +CONFIG_USART2_BAUD=57600 +CONFIG_USART2_IFLOWCONTROL=y +CONFIG_USART2_OFLOWCONTROL=y +CONFIG_USART2_RXBUFSIZE=600 +CONFIG_USART2_RXDMA=y +CONFIG_USART2_TXBUFSIZE=1100 +CONFIG_USART3_BAUD=57600 +CONFIG_USART3_IFLOWCONTROL=y +CONFIG_USART3_OFLOWCONTROL=y +CONFIG_USART3_RXBUFSIZE=300 +CONFIG_USART3_RXDMA=y +CONFIG_USART3_TXBUFSIZE=600 +CONFIG_USART6_BAUD=57600 +CONFIG_USART6_RXBUFSIZE=300 +CONFIG_USART6_RXDMA=y +CONFIG_USART6_TXBUFSIZE=300 +CONFIG_USBDEV=y +CONFIG_USBDEV_BUSPOWERED=y +CONFIG_USBDEV_MAXPOWER=500 +CONFIG_USEC_PER_TICK=1000 +CONFIG_USERMAIN_STACKSIZE=2944 +CONFIG_USER_ENTRYPOINT="nsh_main" diff --git a/boards/thepeach/k1/nuttx-config/scripts/script.ld b/boards/thepeach/k1/nuttx-config/scripts/script.ld new file mode 100644 index 0000000000..6d92733df8 --- /dev/null +++ b/boards/thepeach/k1/nuttx-config/scripts/script.ld @@ -0,0 +1,146 @@ +/**************************************************************************** + * scripts/ld.script + * + * Copyright (C) 2011 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/* The STM32F427 has 2048Kb of FLASH beginning at address 0x0800:0000 and + * 256Kb of SRAM. SRAM is split up into three blocks: + * + * 1) 112Kb of SRAM beginning at address 0x2000:0000 + * 2) 16Kb of SRAM beginning at address 0x2001:c000 + * 3) 64Kb of SRAM beginning at address 0x2002:0000 + * 4) 64Kb of TCM SRAM beginning at address 0x1000:0000 + * + * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000 + * where the code expects to begin execution by jumping to the entry point in + * the 0x0800:0000 address range. + * + * The first 0x4000 of flash is reserved for the bootloader. + */ + +MEMORY +{ + flash (rx) : ORIGIN = 0x08004000, LENGTH = 2032K + sram (rwx) : ORIGIN = 0x20000000, LENGTH = 192K + ccsram (rwx) : ORIGIN = 0x10000000, LENGTH = 64K +} + +OUTPUT_ARCH(arm) + +ENTRY(__start) /* treat __start as the anchor for dead code stripping */ +EXTERN(_vectors) /* force the vectors to be included in the output */ + +/* + * Ensure that abort() is present in the final object. The exception handling + * code pulled in by libgcc.a requires it (and that code cannot be easily avoided). + */ +EXTERN(abort) +EXTERN(_bootdelay_signature) + +SECTIONS +{ + .text : { + _stext = ABSOLUTE(.); + *(.vectors) + . = ALIGN(32); + /* + This signature provides the bootloader with a way to delay booting + */ + _bootdelay_signature = ABSOLUTE(.); + FILL(0xffecc2925d7d05c5) + . += 8; + *(.text .text.*) + *(.fixup) + *(.gnu.warning) + *(.rodata .rodata.*) + *(.gnu.linkonce.t.*) + *(.got) + *(.gcc_except_table) + *(.gnu.linkonce.r.*) + _etext = ABSOLUTE(.); + + } > flash + + /* + * Init functions (static constructors and the like) + */ + .init_section : { + _sinit = ABSOLUTE(.); + KEEP(*(.init_array .init_array.*)) + _einit = ABSOLUTE(.); + } > flash + + + .ARM.extab : { + *(.ARM.extab*) + } > flash + + __exidx_start = ABSOLUTE(.); + .ARM.exidx : { + *(.ARM.exidx*) + } > flash + __exidx_end = ABSOLUTE(.); + + _eronly = ABSOLUTE(.); + + .data : { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + CONSTRUCTORS + _edata = ABSOLUTE(.); + } > sram AT > flash + + .bss : { + _sbss = ABSOLUTE(.); + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + . = ALIGN(4); + _ebss = ABSOLUTE(.); + } > sram + + /* Stabs debugging sections. */ + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_info 0 : { *(.debug_info) } + .debug_line 0 : { *(.debug_line) } + .debug_pubnames 0 : { *(.debug_pubnames) } + .debug_aranges 0 : { *(.debug_aranges) } +} diff --git a/boards/thepeach/k1/src/CMakeLists.txt b/boards/thepeach/k1/src/CMakeLists.txt new file mode 100644 index 0000000000..a7db4590f0 --- /dev/null +++ b/boards/thepeach/k1/src/CMakeLists.txt @@ -0,0 +1,50 @@ +############################################################################ +# +# Copyright (c) 2015 PX4 Development Team. All rights reserved. +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name PX4 nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +add_library(drivers_board + can.c + i2c.cpp + init.c + led.c + spi.cpp + timer_config.cpp + usb.c +) +target_link_libraries(drivers_board + PRIVATE + arch_spi + drivers__led # drv_led_start + nuttx_arch # sdio + nuttx_drivers # sdio + px4_layer +) diff --git a/boards/thepeach/k1/src/board_config.h b/boards/thepeach/k1/src/board_config.h new file mode 100644 index 0000000000..4b1542e547 --- /dev/null +++ b/boards/thepeach/k1/src/board_config.h @@ -0,0 +1,182 @@ +/**************************************************************************** + * + * Copyright (c) 2013-2016 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file board_config.h + * + * ThePeach K1 internal definitions + */ + +#pragma once + +/**************************************************************************************************** + * Included Files + ****************************************************************************************************/ + +#include +#include +#include + +/**************************************************************************************************** + * Definitions + ****************************************************************************************************/ +/* Configuration ************************************************************************************/ + +/* PX4IO connection configuration */ +#define BOARD_USES_PX4IO_VERSION 2 +#define PX4IO_SERIAL_DEVICE "/dev/ttyS4" +#define PX4IO_SERIAL_TX_GPIO GPIO_USART6_TX +#define PX4IO_SERIAL_RX_GPIO GPIO_USART6_RX +#define PX4IO_SERIAL_BASE STM32_USART6_BASE /* hardwired on the board */ +#define PX4IO_SERIAL_VECTOR STM32_IRQ_USART6 +#define PX4IO_SERIAL_TX_DMAMAP DMAMAP_USART6_TX +#define PX4IO_SERIAL_RX_DMAMAP DMAMAP_USART6_RX +#define PX4IO_SERIAL_RCC_REG STM32_RCC_APB2ENR +#define PX4IO_SERIAL_RCC_EN RCC_APB2ENR_USART6EN +#define PX4IO_SERIAL_CLOCK STM32_PCLK2_FREQUENCY +#define PX4IO_SERIAL_BITRATE 1500000 /* 1.5Mbps -> max rate for IO */ + + +/* PX4FMU GPIOs ***********************************************************************************/ +/* LEDs */ + +#define GPIO_LED1 (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN12) +#define BOARD_OVERLOAD_LED LED_RED + +/* + * ADC channels + * + * These are the channel numbers of the ADCs of the microcontroller that can be used by the Px4 Firmware in the adc driver + */ +#define ADC_CHANNELS (1 << 2) | (1 << 3) | (1 << 4) | (1 << 13) | (1 << 14) | (1 << 15) + +// ADC defines to be used in sensors.cpp to read from a particular channel +#define ADC_BATTERY_VOLTAGE_CHANNEL 2 +#define ADC_BATTERY_CURRENT_CHANNEL 3 +#define ADC_5V_RAIL_SENSE 4 +#define ADC_AIRSPEED_VOLTAGE_CHANNEL 15 + +/* Power supply control and monitoring GPIOs */ +// Signal is not connected +#define GPIO_VDD_5V_PERIPH_EN (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN8) +#define GPIO_VDD_BRICK_VALID (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN5) +#define GPIO_VDD_3V3_SENSORS_EN (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3) +#define GPIO_VDD_5V_PERIPH_OC (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTE|GPIO_PIN15) + +/* Tone alarm output */ +#define TONE_ALARM_TIMER 2 /* timer 2 */ +#define TONE_ALARM_CHANNEL 1 /* channel 1 */ +#define GPIO_TONE_ALARM_IDLE (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN15) +#define GPIO_TONE_ALARM (GPIO_ALT|GPIO_AF1|GPIO_SPEED_2MHz|GPIO_PUSHPULL|GPIO_PORTA|GPIO_PIN15) + +/* PWM + */ +#define DIRECT_PWM_OUTPUT_CHANNELS 5 + +/* USB OTG FS + * + * PA9 OTG_FS_VBUS VBUS sensing (also connected to the green LED) + */ +#define GPIO_OTGFS_VBUS (GPIO_INPUT|GPIO_FLOAT|GPIO_SPEED_100MHz|GPIO_OPENDRAIN|GPIO_PORTA|GPIO_PIN9) + +/* High-resolution timer */ +#define HRT_TIMER 8 /* use timer8 for the HRT */ +#define HRT_TIMER_CHANNEL 1 /* use capture/compare channel */ + +/* PWM input driver. Use FMU AUX5 pins attached to timer4 channel 2 */ +#define PWMIN_TIMER 4 +#define PWMIN_TIMER_CHANNEL 2 +#define GPIO_PWM_IN GPIO_TIM4_CH2IN_2 + +/* By Providing BOARD_ADC_USB_CONNECTED this board support the ADC + * system_power interface, and therefore provides the true logic + * GPIO BOARD_ADC_xxxx macros. + */ +#define BOARD_ADC_USB_CONNECTED (px4_arch_gpioread(GPIO_OTGFS_VBUS)) +#define BOARD_ADC_BRICK_VALID (!px4_arch_gpioread(GPIO_VDD_BRICK_VALID)) +#define BOARD_ADC_SERVO_VALID (1) +#define BOARD_ADC_PERIPH_5V_OC (!px4_arch_gpioread(GPIO_VDD_5V_PERIPH_OC)) +#define BOARD_ADC_HIPOWER_5V_OC (0) + + +/* This board provides a DMA pool and APIs */ +#define BOARD_DMA_ALLOC_POOL_SIZE 5120 + +/* This board provides the board_on_reset interface */ + +#define BOARD_HAS_ON_RESET 1 + +#define BOARD_HAS_STATIC_MANIFEST 1 + +__BEGIN_DECLS + +/**************************************************************************************************** + * Public Types + ****************************************************************************************************/ + +/**************************************************************************************************** + * Public data + ****************************************************************************************************/ + +#ifndef __ASSEMBLY__ + +/**************************************************************************************************** + * Public Functions + ****************************************************************************************************/ + +extern void board_peripheral_reset(int ms); + +/**************************************************************************************************** + * Name: stm32_usbinitialize + * + * Description: + * Called to configure USB IO. + * + ****************************************************************************************************/ + +extern void stm32_usbinitialize(void); + +/**************************************************************************************************** + * Name: stm32_spiinitialize + * + * Description: + * Called to configure SPI chip select GPIO pins for the PX4FMU board. + * + ****************************************************************************************************/ + +extern void stm32_spiinitialize(void); + +#include + +#endif /* __ASSEMBLY__ */ +__END_DECLS diff --git a/boards/thepeach/k1/src/can.c b/boards/thepeach/k1/src/can.c new file mode 100644 index 0000000000..5a32d62832 --- /dev/null +++ b/boards/thepeach/k1/src/can.c @@ -0,0 +1,130 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file can.c + * + * Board-specific CAN functions. + */ + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include + +#include +#include + +#include +#include + +#include "chip.h" +#include "arm_arch.h" + +#include "stm32.h" +#include "stm32_can.h" +#include "board_config.h" + +#ifdef CONFIG_CAN + +/************************************************************************************ + * Pre-processor Definitions + ************************************************************************************/ +/* Configuration ********************************************************************/ + +#if defined(CONFIG_STM32_CAN1) && defined(CONFIG_STM32_CAN2) +# warning "Both CAN1 and CAN2 are enabled. Assuming only CAN1." +# undef CONFIG_STM32_CAN2 +#endif + +#ifdef CONFIG_STM32_CAN1 +# define CAN_PORT 1 +#else +# define CAN_PORT 2 +#endif + +/************************************************************************************ + * Private Functions + ************************************************************************************/ + +/************************************************************************************ + * Public Functions + ************************************************************************************/ +int can_devinit(void); + +/************************************************************************************ + * Name: can_devinit + * + * Description: + * All STM32 architectures must provide the following interface to work with + * examples/can. + * + ************************************************************************************/ + +int can_devinit(void) +{ + static bool initialized = false; + struct can_dev_s *can; + int ret; + + /* Check if we have already initialized */ + + if (!initialized) { + /* Call stm32_caninitialize() to get an instance of the CAN interface */ + + can = stm32_caninitialize(CAN_PORT); + + if (can == NULL) { + canerr("ERROR: Failed to get CAN interface\n"); + return -ENODEV; + } + + /* Register the CAN driver at "/dev/can0" */ + + ret = can_register("/dev/can0", can); + + if (ret < 0) { + canerr("ERROR: can_register failed: %d\n", ret); + return ret; + } + + /* Now we are initialized */ + + initialized = true; + } + + return OK; +} + +#endif diff --git a/boards/thepeach/k1/src/i2c.cpp b/boards/thepeach/k1/src/i2c.cpp new file mode 100644 index 0000000000..63ec5a5228 --- /dev/null +++ b/boards/thepeach/k1/src/i2c.cpp @@ -0,0 +1,40 @@ +/**************************************************************************** + * + * Copyright (C) 2020 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include + +constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = { + initI2CBusExternal(1), + initI2CBusExternal(2), + +}; diff --git a/boards/thepeach/k1/src/init.c b/boards/thepeach/k1/src/init.c new file mode 100644 index 0000000000..107312832b --- /dev/null +++ b/boards/thepeach/k1/src/init.c @@ -0,0 +1,318 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file init.c + * + * PX4FMU-specific early startup code. This file implements the + * board_app_initialize() function that is called early by nsh during startup. + * + * Code here is run before the rcS script is invoked; it should start required + * subsystems and perform board-specific initialization. + */ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include "board_config.h" +#include + +#include + +#include +#include + +#include + +#include +#include +#include + +/**************************************************************************** + * Pre-Processor Definitions + ****************************************************************************/ + +/* + * Ideally we'd be able to get these from arm_internal.h, + * but since we want to be able to disable the NuttX use + * of leds for system indication at will and there is no + * separate switch, we need to build independent of the + * CONFIG_ARCH_LEDS configuration switch. + */ +__BEGIN_DECLS +extern void led_init(void); +extern void led_on(int led); +extern void led_off(int led); +__END_DECLS + +/**************************************************************************** + * Protected Functions + ****************************************************************************/ +/**************************************************************************** + * Public Functions + ****************************************************************************/ +/************************************************************************************ + * Name: board_on_reset + * + * Description: + * Optionally provided function called on entry to board_system_reset + * It should perform any house keeping prior to the rest. + * + * status - 1 if resetting to boot loader + * 0 if just resetting + * + ************************************************************************************/ +__EXPORT void board_on_reset(int status) +{ + for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) { + px4_arch_configgpio(io_timer_channel_get_gpio_output(i)); + } + + /** + * On resets invoked from system (not boot) insure we establish a low + * output state (discharge the pins) on PWM pins before they become inputs. + */ + + if (status >= 0) { + up_mdelay(400); + } +} + +/************************************************************************************ + * Name: board_peripheral_reset + * + * Description: + * + ************************************************************************************/ +__EXPORT void board_peripheral_reset(int ms) +{ + /* set the peripheral rails off */ + stm32_configgpio(GPIO_VDD_5V_PERIPH_EN); + stm32_gpiowrite(GPIO_VDD_5V_PERIPH_EN, 1); + + /* wait for the peripheral rail to reach GND */ + usleep(ms * 1000); + syslog(LOG_DEBUG, "reset done, %d ms\n", ms); + + /* re-enable power */ + + /* switch the peripheral rail back on */ + stm32_gpiowrite(GPIO_VDD_5V_PERIPH_EN, 0); +} + +/************************************************************************************ + * Name: stm32_boardinitialize + * + * Description: + * All STM32 architectures must provide the following entry point. This entry point + * is called early in the intitialization -- after all memory has been configured + * and mapped but before any devices have been initialized. + * + ************************************************************************************/ + +__EXPORT void +stm32_boardinitialize(void) +{ + // Reset all PWM to Low outputs. + + board_on_reset(-1); + + /* configure LEDs */ + + board_autoled_initialize(); + + /* configure ADC pins */ + + px4_arch_configgpio(GPIO_ADC1_IN2); /* BATT_VOLTAGE_SENS */ + px4_arch_configgpio(GPIO_ADC1_IN3); /* BATT_CURRENT_SENS */ + px4_arch_configgpio(GPIO_ADC1_IN4); /* VDD_5V_SENS */ + px4_arch_configgpio(GPIO_ADC1_IN13); /* FMU_AUX_ADC_1 */ + px4_arch_configgpio(GPIO_ADC1_IN14); /* FMU_AUX_ADC_2 */ + px4_arch_configgpio(GPIO_ADC1_IN15); /* PRESSURE_SENS */ + + /* configure power supply control/sense pins */ + px4_arch_configgpio(GPIO_VDD_5V_PERIPH_EN); + px4_arch_configgpio(GPIO_VDD_3V3_SENSORS_EN); + px4_arch_configgpio(GPIO_VDD_BRICK_VALID); + px4_arch_configgpio(GPIO_VDD_5V_PERIPH_OC); + + /* configure CAN interface */ + + stm32_configgpio(GPIO_CAN1_RX); + stm32_configgpio(GPIO_CAN1_TX); + + /* configure SPI interfaces */ + + stm32_spiinitialize(); + + /* configure USB interface */ + + stm32_usbinitialize(); + +} + +/**************************************************************************** + * Name: board_app_initialize + * + * Description: + * Perform application specific initialization. This function is never + * called directly from application code, but only indirectly via the + * (non-standard) boardctl() interface using the command BOARDIOC_INIT. + * + * Input Parameters: + * arg - The boardctl() argument is passed to the board_app_initialize() + * implementation without modification. The argument has no + * meaning to NuttX; the meaning of the argument is a contract + * between the board-specific initalization logic and the the + * matching application logic. The value cold be such things as a + * mode enumeration value, a set of DIP switch switch settings, a + * pointer to configuration data read from a file or serial FLASH, + * or whatever you would like to do with it. Every implementation + * should accept zero/NULL as a default configuration. + * + * Returned Value: + * Zero (OK) is returned on success; a negated errno value is returned on + * any failure to indicate the nature of the failure. + * + ****************************************************************************/ + + +static struct spi_dev_s *spi1; +static struct spi_dev_s *spi2; +static struct sdio_dev_s *sdio; + +__EXPORT int board_app_initialize(uintptr_t arg) +{ + + px4_platform_init(); + + /* configure the DMA allocator */ + + if (board_dma_alloc_init() < 0) { + syslog(LOG_ERR, "DMA alloc FAILED\n"); + } + +#if defined(SERIAL_HAVE_RXDMA) + // set up the serial DMA polling at 1ms intervals for received bytes that have not triggered a DMA event. + static struct hrt_call serial_dma_call; + hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL); +#endif + + /* initial LED state */ + drv_led_start(); + led_off(LED_AMBER); + + if (board_hardfault_init(2, true) != 0) { + led_on(LED_AMBER); + } + + /* Configure SPI-based devices */ + + spi1 = px4_spibus_initialize(1); + + if (!spi1) { + syslog(LOG_ERR, "[boot] FAILED to initialize SPI port 1\n"); + led_on(LED_AMBER); + } + + /* Default SPI1 to 1MHz and de-assert the known chip selects. */ + SPI_SETFREQUENCY(spi1, 10000000); + SPI_SETBITS(spi1, 8); + SPI_SETMODE(spi1, SPIDEV_MODE3); + up_udelay(20); + + /* Get the SPI port for the FRAM */ + + spi2 = px4_spibus_initialize(2); + + if (!spi2) { + syslog(LOG_ERR, "[boot] FAILED to initialize SPI port 2\n"); + led_on(LED_AMBER); + } + + /* Default SPI2 to 37.5 MHz (40 MHz rounded to nearest valid divider, F4 max) + * and de-assert the known chip selects. */ + + // XXX start with 10.4 MHz in FRAM usage and go up to 37.5 once validated + SPI_SETFREQUENCY(spi2, 12 * 1000 * 1000); + SPI_SETBITS(spi2, 8); + SPI_SETMODE(spi2, SPIDEV_MODE3); + SPI_SELECT(spi2, SPIDEV_FLASH(0), false); + + +#ifdef CONFIG_MMCSD + /* First, get an instance of the SDIO interface */ + sdio = sdio_initialize(CONFIG_NSH_MMCSDSLOTNO); + + if (!sdio) { + syslog(LOG_ERR, "[boot] Failed to initialize SDIO slot %d\n", CONFIG_NSH_MMCSDSLOTNO); + led_on(LED_AMBER); + } + + /* Now bind the SDIO interface to the MMC/SD driver */ + int ret = mmcsd_slotinitialize(CONFIG_NSH_MMCSDMINOR, sdio); + + if (ret != OK) { + syslog(LOG_ERR, "[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret); + led_on(LED_AMBER); + } + + /* Then let's guess and say that there is a card in the slot. There is no card detect GPIO. */ + sdio_mediachange(sdio, true); + +#endif + + /* Configure the HW based on the manifest */ + px4_platform_configure(); + + return OK; +} diff --git a/boards/thepeach/k1/src/led.c b/boards/thepeach/k1/src/led.c new file mode 100644 index 0000000000..8a70a4cb29 --- /dev/null +++ b/boards/thepeach/k1/src/led.c @@ -0,0 +1,96 @@ +/**************************************************************************** + * + * Copyright (c) 2013 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file led.c + * + * LED backend. + */ + +#include + +#include + +#include "stm32.h" +#include + +#include "board_config.h" + +/* + * Ideally we'd be able to get these from arm_internal.h, + * but since we want to be able to disable the NuttX use + * of leds for system indication at will and there is no + * separate switch, we need to build independent of the + * CONFIG_ARCH_LEDS configuration switch. + */ +__BEGIN_DECLS +extern void led_init(void); +extern void led_on(int led); +extern void led_off(int led); +extern void led_toggle(int led); +__END_DECLS + +__EXPORT void led_init() +{ + /* Configure LED1 GPIO for output */ + + px4_arch_configgpio(GPIO_LED1); +} + +__EXPORT void led_on(int led) +{ + if (led == 1) { + /* Pull down to switch on */ + px4_arch_gpiowrite(GPIO_LED1, false); + } +} + +__EXPORT void led_off(int led) +{ + if (led == 1) { + /* Pull up to switch off */ + px4_arch_gpiowrite(GPIO_LED1, true); + } +} + +__EXPORT void led_toggle(int led) +{ + if (led == 1) { + if (px4_arch_gpioread(GPIO_LED1)) { + px4_arch_gpiowrite(GPIO_LED1, false); + + } else { + px4_arch_gpiowrite(GPIO_LED1, true); + } + } +} diff --git a/boards/thepeach/k1/src/spi.cpp b/boards/thepeach/k1/src/spi.cpp new file mode 100644 index 0000000000..77d0c37214 --- /dev/null +++ b/boards/thepeach/k1/src/spi.cpp @@ -0,0 +1,49 @@ +/**************************************************************************** + * + * Copyright (C) 2020 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include +#include +#include + +constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = { + initSPIBus(SPI::Bus::SPI1, { + initSPIDevice(DRV_IMU_DEVTYPE_ICM20602, SPI::CS{GPIO::PortC, GPIO::Pin15}, SPI::DRDY{GPIO::PortC, GPIO::Pin14}), + initSPIDevice(DRV_BARO_DEVTYPE_MS5611, SPI::CS{GPIO::PortD, GPIO::Pin7}), + initSPIDevice(DRV_IMU_DEVTYPE_MPU9250, SPI::CS{GPIO::PortC, GPIO::Pin2}, SPI::DRDY{GPIO::PortD, GPIO::Pin15}), + }), + initSPIBus(SPI::Bus::SPI2, { + initSPIDevice(SPIDEV_FLASH(0), SPI::CS{GPIO::PortD, GPIO::Pin10}), + }), +}; + +static constexpr bool unused = validateSPIConfig(px4_spi_buses); diff --git a/boards/thepeach/k1/src/timer_config.cpp b/boards/thepeach/k1/src/timer_config.cpp new file mode 100644 index 0000000000..c96e7c5664 --- /dev/null +++ b/boards/thepeach/k1/src/timer_config.cpp @@ -0,0 +1,50 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include + +constexpr io_timers_t io_timers[MAX_IO_TIMERS] = { + initIOTimer(Timer::Timer1), + initIOTimer(Timer::Timer4), +}; + +constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = { + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel4}, {GPIO::PortE, GPIO::Pin14}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel3}, {GPIO::PortE, GPIO::Pin13}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel2}, {GPIO::PortE, GPIO::Pin11}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel1}, {GPIO::PortE, GPIO::Pin9}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer4, Timer::Channel2}, {GPIO::PortD, GPIO::Pin13}), +}; + +constexpr io_timers_channel_mapping_t io_timers_channel_mapping = + initIOTimerChannelMapping(io_timers, timer_io_channels); diff --git a/boards/thepeach/k1/src/usb.c b/boards/thepeach/k1/src/usb.c new file mode 100644 index 0000000000..6fbea86a0b --- /dev/null +++ b/boards/thepeach/k1/src/usb.c @@ -0,0 +1,108 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file usb.c + * + * Board-specific USB functions. + */ + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include + +#include +#include +#include +#include + +#include +#include + +#include +#include + +#include "board_config.h" + +/************************************************************************************ + * Definitions + ************************************************************************************/ + +/************************************************************************************ + * Private Functions + ************************************************************************************/ + +/************************************************************************************ + * Public Functions + ************************************************************************************/ + +/************************************************************************************ + * Name: stm32_usbinitialize + * + * Description: + * Called to setup USB-related GPIO pins for the PX4FMU board. + * + ************************************************************************************/ + +__EXPORT void stm32_usbinitialize(void) +{ + /* The OTG FS has an internal soft pull-up */ + + /* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */ + +#ifdef CONFIG_STM32_OTGFS + px4_arch_configgpio(GPIO_OTGFS_VBUS); + /* XXX We only support device mode + px4_arch_configgpio(GPIO_OTGFS_PWRON); + px4_arch_configgpio(GPIO_OTGFS_OVER); + */ +#endif +} + +/************************************************************************************ + * Name: stm32_usbsuspend + * + * Description: + * Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is + * used. This function is called whenever the USB enters or leaves suspend mode. + * This is an opportunity for the board logic to shutdown clocks, power, etc. + * while the USB is suspended. + * + ************************************************************************************/ + +__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume) +{ + //ulldbg("resume: %d\n", resume); +} diff --git a/boards/thepeach/r1/default.px4board b/boards/thepeach/r1/default.px4board new file mode 100644 index 0000000000..4d4ab00a94 --- /dev/null +++ b/boards/thepeach/r1/default.px4board @@ -0,0 +1,107 @@ +CONFIG_BOARD_TOOLCHAIN="arm-none-eabi" +CONFIG_BOARD_ARCHITECTURE="cortex-m4" +CONFIG_BOARD_CONSTRAINED_MEMORY=y +CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS3" +CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS1" +CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS2" +CONFIG_BOARD_SERIAL_TEL4="/dev/ttyS6" +CONFIG_DRIVERS_ADC_ADS1115=y +CONFIG_DRIVERS_ADC_BOARD_ADC=y +CONFIG_COMMON_BAROMETERS=y +CONFIG_DRIVERS_BATT_SMBUS=y +CONFIG_DRIVERS_CAMERA_CAPTURE=y +CONFIG_DRIVERS_CAMERA_TRIGGER=y +CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y +CONFIG_COMMON_DISTANCE_SENSOR=y +CONFIG_DRIVERS_DSHOT=y +CONFIG_DRIVERS_GPS=y +CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y +CONFIG_DRIVERS_IMU_INVENSENSE_ICM20948=y +CONFIG_DRIVERS_IMU_INVENSENSE_MPU9250=y +CONFIG_DRIVERS_IRLOCK=y +CONFIG_COMMON_LIGHT=y +CONFIG_COMMON_MAGNETOMETER=y +CONFIG_COMMON_OPTICAL_FLOW=y +CONFIG_DRIVERS_OSD=y +CONFIG_DRIVERS_PCA9685=y +CONFIG_DRIVERS_PCA9685_PWM_OUT=y +CONFIG_DRIVERS_POWER_MONITOR_INA226=y +CONFIG_DRIVERS_PWM_INPUT=y +CONFIG_DRIVERS_PWM_OUT=y +CONFIG_DRIVERS_PWM_OUT_SIM=y +CONFIG_DRIVERS_PX4IO=y +CONFIG_DRIVERS_ROBOCLAW=y +CONFIG_DRIVERS_RPM=y +CONFIG_DRIVERS_SMART_BATTERY_BATMON=y +CONFIG_COMMON_TELEMETRY=y +CONFIG_DRIVERS_TONE_ALARM=y +CONFIG_DRIVERS_UAVCAN=y +CONFIG_BOARD_UAVCAN_INTERFACES=1 +CONFIG_MODULES_AIRSPEED_SELECTOR=y +CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y +CONFIG_MODULES_BATTERY_STATUS=y +CONFIG_MODULES_CAMERA_FEEDBACK=y +CONFIG_MODULES_COMMANDER=y +CONFIG_MODULES_DATAMAN=y +CONFIG_MODULES_EKF2=y +CONFIG_MODULES_ESC_BATTERY=y +CONFIG_MODULES_EVENTS=y +CONFIG_MODULES_FLIGHT_MODE_MANAGER=y +CONFIG_MODULES_FW_ATT_CONTROL=y +CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y +CONFIG_MODULES_FW_POS_CONTROL_L1=y +CONFIG_MODULES_GYRO_CALIBRATION=y +CONFIG_MODULES_GYRO_FFT=y +CONFIG_MODULES_LAND_DETECTOR=y +CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y +CONFIG_MODULES_LOAD_MON=y +CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=y +CONFIG_MODULES_LOGGER=y +CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y +CONFIG_MODULES_MANUAL_CONTROL=y +CONFIG_MODULES_MAVLINK=y +CONFIG_MODULES_MC_ATT_CONTROL=y +CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y +CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y +CONFIG_MODULES_MC_POS_CONTROL=y +CONFIG_MODULES_MC_RATE_CONTROL=y +CONFIG_MODULES_CONTROL_ALLOCATOR=y +CONFIG_MODULES_NAVIGATOR=y +CONFIG_MODULES_RC_UPDATE=y +CONFIG_MODULES_ROVER_POS_CONTROL=y +CONFIG_MODULES_SENSORS=y +CONFIG_MODULES_SIH=y +CONFIG_MODULES_TEMPERATURE_COMPENSATION=y +CONFIG_MODULES_UUV_ATT_CONTROL=y +CONFIG_MODULES_UUV_POS_CONTROL=y +CONFIG_MODULES_GIMBAL=y +CONFIG_MODULES_VTOL_ATT_CONTROL=y +CONFIG_SYSTEMCMDS_BL_UPDATE=y +CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y +CONFIG_SYSTEMCMDS_DUMPFILE=y +CONFIG_SYSTEMCMDS_GPIO=y +CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y +CONFIG_SYSTEMCMDS_I2CDETECT=y +CONFIG_SYSTEMCMDS_LED_CONTROL=y +CONFIG_SYSTEMCMDS_MFT=y +CONFIG_SYSTEMCMDS_MIXER=y +CONFIG_SYSTEMCMDS_MOTOR_TEST=y +CONFIG_SYSTEMCMDS_MTD=y +CONFIG_SYSTEMCMDS_NSHTERM=y +CONFIG_SYSTEMCMDS_PARAM=y +CONFIG_SYSTEMCMDS_PERF=y +CONFIG_SYSTEMCMDS_PWM=y +CONFIG_SYSTEMCMDS_REBOOT=y +CONFIG_SYSTEMCMDS_REFLECT=y +CONFIG_SYSTEMCMDS_SD_BENCH=y +CONFIG_SYSTEMCMDS_SD_STRESS=y +CONFIG_SYSTEMCMDS_SERIAL_TEST=y +CONFIG_SYSTEMCMDS_SYSTEM_TIME=y +CONFIG_SYSTEMCMDS_TOP=y +CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y +CONFIG_SYSTEMCMDS_TUNE_CONTROL=y +CONFIG_SYSTEMCMDS_UORB=y +CONFIG_SYSTEMCMDS_USB_CONNECTED=y +CONFIG_SYSTEMCMDS_VER=y +CONFIG_SYSTEMCMDS_WORK_QUEUE=y +CONFIG_EXAMPLES_FAKE_GPS=y diff --git a/boards/thepeach/r1/extras/px4_io-v2_default.bin b/boards/thepeach/r1/extras/px4_io-v2_default.bin new file mode 100755 index 0000000000..25a00e2357 Binary files /dev/null and b/boards/thepeach/r1/extras/px4_io-v2_default.bin differ diff --git a/boards/thepeach/r1/extras/thepeach_r1_bootloader.bin b/boards/thepeach/r1/extras/thepeach_r1_bootloader.bin new file mode 100755 index 0000000000..cdae8101a8 Binary files /dev/null and b/boards/thepeach/r1/extras/thepeach_r1_bootloader.bin differ diff --git a/boards/thepeach/r1/firmware.prototype b/boards/thepeach/r1/firmware.prototype new file mode 100644 index 0000000000..5db240d57e --- /dev/null +++ b/boards/thepeach/r1/firmware.prototype @@ -0,0 +1,13 @@ +{ + "board_id": 213, + "magic": "PX4FWv1", + "description": "Firmware for the ThePeach R1 board", + "image": "", + "build_time": 0, + "summary": "ThePeach R1", + "version": "0.1", + "image_size": 0, + "image_maxsize": 2080768, + "git_identity": "", + "board_revision": 0 +} diff --git a/boards/thepeach/r1/init/rc.board_defaults b/boards/thepeach/r1/init/rc.board_defaults new file mode 100644 index 0000000000..f22fa838f4 --- /dev/null +++ b/boards/thepeach/r1/init/rc.board_defaults @@ -0,0 +1,7 @@ +#!/bin/sh +# +# board specific defaults +#------------------------------------------------------------------------------ + +param set-default BAT1_V_DIV 18.1 +param set-default BAT1_A_PER_V 36.367515152 diff --git a/boards/thepeach/r1/init/rc.board_sensors b/boards/thepeach/r1/init/rc.board_sensors new file mode 100644 index 0000000000..fb2d1c3aa8 --- /dev/null +++ b/boards/thepeach/r1/init/rc.board_sensors @@ -0,0 +1,10 @@ +#!/bin/sh +# +# Board specific sensors init +#------------------------------------------------------------------------------ +board_adc start + +# SPI1 +ms5611 -s -b 1 start +icm20602 -s -b 1 -R 0 start +mpu9250 -s -b 1 -R 0 -M start diff --git a/boards/thepeach/r1/nuttx-config/include/board.h b/boards/thepeach/r1/nuttx-config/include/board.h new file mode 100644 index 0000000000..21f49262fe --- /dev/null +++ b/boards/thepeach/r1/nuttx-config/include/board.h @@ -0,0 +1,266 @@ +/************************************************************************************ + * board.h + * include/arch/board/board.h + * + * Copyright (C) 2009, 2016 Gregory Nutt. All rights reserved. + * Authors: Gregory Nutt + * David Sidrane + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ************************************************************************************/ + +#ifndef __ARCH_BOARD_BOARD_H +#define __ARCH_BOARD_BOARD_H + +/************************************************************************************ + * Included Files + ************************************************************************************/ +#include "board_dma_map.h" + +#include +#ifndef __ASSEMBLY__ +# include +#endif + +#include + +/************************************************************************************ + * Definitions + ************************************************************************************/ + +/* Clocking *************************************************************************/ +/* The PX4FMUV2 uses a 24MHz crystal connected to the HSE. + * + * This is the "standard" configuration as set up by arch/arm/src/stm32f40xx_rcc.c: + * System Clock source : PLL (HSE) + * SYSCLK(Hz) : 168000000 Determined by PLL configuration + * HCLK(Hz) : 168000000 (STM32_RCC_CFGR_HPRE) + * AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE) + * APB1 Prescaler : 4 (STM32_RCC_CFGR_PPRE1) + * APB2 Prescaler : 2 (STM32_RCC_CFGR_PPRE2) + * HSE Frequency(Hz) : 24000000 (STM32_BOARD_XTAL) + * PLLM : 24 (STM32_PLLCFG_PLLM) + * PLLN : 336 (STM32_PLLCFG_PLLN) + * PLLP : 2 (STM32_PLLCFG_PLLP) + * PLLQ : 7 (STM32_PLLCFG_PPQ) + * Main regulator output voltage : Scale1 mode Needed for high speed SYSCLK + * Flash Latency(WS) : 5 + * Prefetch Buffer : OFF + * Instruction cache : ON + * Data cache : ON + * Require 48MHz for USB OTG FS, : Enabled + * SDIO and RNG clock + */ + +/* HSI - 16 MHz RC factory-trimmed + * LSI - 32 KHz RC + * HSE - On-board crystal frequency is 24MHz + * LSE - not installed + */ + +#define STM32_BOARD_XTAL 24000000ul + +#define STM32_HSI_FREQUENCY 16000000ul +#define STM32_LSI_FREQUENCY 32000 +#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL +//#define STM32_LSE_FREQUENCY 32768 + +/* Main PLL Configuration. + * + * PLL source is HSE + * PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN + * = (25,000,000 / 25) * 336 + * = 336,000,000 + * SYSCLK = PLL_VCO / PLLP + * = 336,000,000 / 2 = 168,000,000 + * USB OTG FS, SDIO and RNG Clock + * = PLL_VCO / PLLQ + * = 48,000,000 + */ + +#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(24) +#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336) +#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2 +#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7) + +#define STM32_SYSCLK_FREQUENCY 168000000ul + +/* AHB clock (HCLK) is SYSCLK (168MHz) */ + +#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */ +#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY +#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */ + +/* APB1 clock (PCLK1) is HCLK/4 (42MHz) */ + +#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */ +#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4) + +/* Timers driven from APB1 will be twice PCLK1 */ + +#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY) +#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY) + +/* APB2 clock (PCLK2) is HCLK/2 (84MHz) */ + +#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */ +#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2) + +/* Timers driven from APB2 will be twice PCLK2 */ + +#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY) +#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY) + +/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx + * otherwise frequency is 2xAPBx. + * Note: TIM1,8-11 are on APB2, others on APB1 + */ + +#define BOARD_TIM1_FREQUENCY STM32_APB2_TIM1_CLKIN +#define BOARD_TIM2_FREQUENCY STM32_APB1_TIM2_CLKIN +#define BOARD_TIM3_FREQUENCY STM32_APB1_TIM3_CLKIN +#define BOARD_TIM4_FREQUENCY STM32_APB1_TIM4_CLKIN +#define BOARD_TIM5_FREQUENCY STM32_APB1_TIM5_CLKIN +#define BOARD_TIM6_FREQUENCY STM32_APB1_TIM6_CLKIN +#define BOARD_TIM7_FREQUENCY STM32_APB1_TIM7_CLKIN +#define BOARD_TIM8_FREQUENCY STM32_APB2_TIM8_CLKIN +#define BOARD_TIM9_FREQUENCY STM32_APB2_TIM9_CLKIN +#define BOARD_TIM10_FREQUENCY STM32_APB2_TIM10_CLKIN +#define BOARD_TIM11_FREQUENCY STM32_APB2_TIM11_CLKIN +#define BOARD_TIM12_FREQUENCY STM32_APB1_TIM12_CLKIN +#define BOARD_TIM13_FREQUENCY STM32_APB1_TIM13_CLKIN +#define BOARD_TIM14_FREQUENCY STM32_APB1_TIM14_CLKIN + +/* SDIO dividers. Note that slower clocking is required when DMA is disabled + * in order to avoid RX overrun/TX underrun errors due to delayed responses + * to service FIFOs in interrupt driven mode. These values have not been + * tuned!!! + * + * SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(118+2)=400 KHz + */ + +#define SDIO_INIT_CLKDIV (118 << SDIO_CLKCR_CLKDIV_SHIFT) + +/* DMA ON: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(1+2)=16 MHz + * DMA OFF: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(2+2)=12 MHz + */ + +#ifdef CONFIG_STM32_SDIO_DMA +# define SDIO_MMCXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) +#else +# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) +#endif + +/* DMA ON: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(1+2)=16 MHz + * DMA OFF: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(2+2)=12 MHz + */ + +#ifdef CONFIG_STM32_SDIO_DMA +# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) +#else +# define SDIO_SDXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) +#endif + +/* Alternate function pin selections ************************************************/ + +/* UARTs */ + +#define GPIO_USART1_RX GPIO_USART1_RX_1 /* Console in from IO */ +#define GPIO_USART1_TX 0 /* USART1 is RX-only */ + +#define GPIO_USART2_RX GPIO_USART2_RX_2 +#define GPIO_USART2_TX GPIO_USART2_TX_2 +#define GPIO_USART2_RTS GPIO_USART2_RTS_2 +#define GPIO_USART2_CTS GPIO_USART2_CTS_2 + +#define GPIO_USART3_RX GPIO_USART3_RX_3 +#define GPIO_USART3_TX GPIO_USART3_TX_3 +#define GPIO_USART3_RTS GPIO_USART3_RTS_2 +#define GPIO_USART3_CTS GPIO_USART3_CTS_2 + +#define GPIO_UART4_RX GPIO_UART4_RX_1 +#define GPIO_UART4_TX GPIO_UART4_TX_1 + +#define GPIO_USART6_RX GPIO_USART6_RX_1 +#define GPIO_USART6_TX GPIO_USART6_TX_1 + +#define GPIO_UART7_RX GPIO_UART7_RX_1 +#define GPIO_UART7_TX GPIO_UART7_TX_1 + +/* UART8 has no alternate pin config */ + +/* CAN + * + * CAN1 is routed to the onboard transceiver. + */ + +#define GPIO_CAN1_RX GPIO_CAN1_RX_3 +#define GPIO_CAN1_TX GPIO_CAN1_TX_3 + +/* I2C + * + * The optional _GPIO configurations allow the I2C driver to manually + * reset the bus to clear stuck slaves. They match the pin configuration, + * but are normally-high GPIOs. + */ + +#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2 +#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2 +#define GPIO_I2C1_SCL_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN8) +#define GPIO_I2C1_SDA_GPIO (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9) + +/* SPI + * + * There are sensors on SPI1, and SPI2 is connected to the FRAM. + */ + +#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 +#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 +#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 + +#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 +#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 +#define GPIO_SPI2_SCK GPIO_SPI2_SCK_2 + +#define GPIO_SPI4_MISO GPIO_SPI4_MISO_1 +#define GPIO_SPI4_MOSI GPIO_SPI4_MOSI_1 +#define GPIO_SPI4_SCK GPIO_SPI4_SCK_1 + + +#endif /* __ARCH_BOARD_BOARD_H */ diff --git a/boards/thepeach/r1/nuttx-config/include/board_dma_map.h b/boards/thepeach/r1/nuttx-config/include/board_dma_map.h new file mode 100644 index 0000000000..96a4c81517 --- /dev/null +++ b/boards/thepeach/r1/nuttx-config/include/board_dma_map.h @@ -0,0 +1,93 @@ +/**************************************************************************** + * + * Copyright (c) 2020 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#pragma once + +/* +| DMA1 | Stream 0 | Stream 1 | Stream 2 | Stream 3 | Stream 4 | Stream 5 | Stream 6 | Stream 7 | +|------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------| +| Channel 0 | SPI3_RX_1 | - | SPI3_RX_2 | SPI2_RX | SPI2_TX | SPI3_TX_1 | - | SPI3_TX_2 | +| Channel 1 | I2C1_RX | - | TIM7_UP_1 | - | TIM7_UP_2 | I2C1_RX_1 | I2C1_TX | I2C1_TX_1 | +| Channel 2 | TIM4_CH1 | - | I2C4_RX | TIM4_CH2 | - | I2C4_RX | TIM4_UP | TIM4_CH3 | +| Channel 3 | - | TIM2_UP_1 | I2C3_RX_1 | I2C2_EXT_RX | I2C3_TX | TIM2_CH1 | TIM2_CH2 | TIM2_UP_2 | +| | | TIM2_CH3 | | | | | TIM2_CH4_1 | TIM2_CH4_2 | +| Channel 4 | UART5_RX | USART3_RX | UART4_RX | USART3_TX_1 | UART4_TX | USART2_RX | USART2_TX | UART5_TX | +| Channel 5 | UART8_TX | UART7_TX | TIM3_CH4 | UART7_RX | TIM3_CH1 | TIM3_CH2 | UART8_RX | TIM3_CH3 | +| | | | TIM3_UP | | TIM3_TRIG | | | | +| Channel 6 | TIM5_CH3 | TIM5_CH4_1 | TIM5_CH1 | TIM5_CH4_2 | TIM5_CH2 | - | TIM5_UP_2 | - | +| | TIM5_UP_1 | TIM5_TRIG_1 | | TIM5_TRIG_2 | | | | | +| Channel 7 | - | TIM6_UP | I2C2_RX | I2C2_RX_1 | USART3_TX_2 | DAC1 | DAC2 | I2C2_TX | +| | | | | | | | | | +| Usage | | USART3_RX | UART4_RX | UART7_RX | | USART2_RX | TIM4_UP | | + + +| DMA2 | Stream 0 | Stream 1 | Stream 2 | Stream 3 | Stream 4 | Stream 5 | Stream 6 | Stream 7 | +|------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------|------------------| +| Channel 0 | ADC1_1 | SAI1_A | TIM8_CH1_1 | SAI1_A_1 | ADC1_2 | SAI1_B_1 | TIM1_CH1_1 | - | +| | | | TIM8_CH2_1 | | | | TIM1_CH2_1 | | +| | | | TIM8_CH3_1 | | | | TIM1_CH3_1 | | +| Channel 1 | - | DCMI_1 | ADC2_1 | ADC2_2 | SAI1_B | SPI6_TX | SPI6_RX | DCMI_2 | +| Channel 2 | ADC3_1 | ADC3_2 | - | SPI5_RX_1 | SPI5_TX_1 | CRYP_OUT | CRYP_IN | HASH_IN | +| Channel 3 | SPI1_RX_1 | - | SPI1_RX_2 | SPI1_TX_1 | - | SPI1_TX_2 | - | QUADSPI | +| Channel 4 | SPI4_RX_1 | SPI4_TX_1 | USART1_RX_1 | SDIO | - | USART1_RX_2 | SDIO | USART1_TX | +| Channel 5 | - | USART6_RX_1 | USART6_RX_2 | SPI4_RX_2 | SPI4_TX_2 | - | USART6_TX_1 | USART6_TX_2 | +| Channel 6 | TIM1_TRIG_1 | TIM1_CH1_2 | TIM1_CH2_2 | TIM1_CH1 | TIM1_CH4 | TIM1_UP | TIM1_CH3_2 | - | +| | | | | | TIM1_TRIG_2 | | | | +| | | | | | TIM1_COM | | | | +| Channel 7 | - | TIM8_UP | TIM8_CH1_2 | TIM8_CH2_2 | TIM8_CH3_2 | SPI5_RX_2 | SPI5_TX_2 | TIM8_CH4 | +| | | | | | | | | TIM8_TRIG | +| | | | | | | | | TIM8_COM | +| | | | | | | | | | +| Usage | | USART6_RX_1 | SPI1_RX_2 | SPI1_TX_1 | | TIM1_UP | SDIO | USART6_TX_2 | + */ + +// DMA1 Channel/Stream Selections +//--------------------------------------------//---------------------------//---------------- +// DMAMAP_USART3_RX // DMA1, Stream 1, Channel 4 +// DMAMAP_UART4_RX // DMA1, Stream 2, Channel 4 +// DMAMAP_UART7_RX // DMA1, Stream 3, Channel 5 +// AVAILABLE // DMA1, Stream 4 +// DMAMAP_USART2_RX // DMA1, Stream 5, Channel 4 +// DMAMAP_TIM4_UP // DMA1, Stream 6, Channel 2 (DSHOT) + + +// DMA2 Channel/Stream Selections +//--------------------------------------------//---------------------------//---------------- +// AVAILABLE // DMA2, Stream 0 +#define DMAMAP_USART6_RX DMAMAP_USART6_RX_1 // DMA2, Stream 1, Channel 4 (PX4IO RX) +#define DMACHAN_SPI1_RX DMAMAP_SPI1_RX_2 // DMA2, Stream 2, Channel 3 (SPI1 sensors RX) +#define DMACHAN_SPI1_TX DMAMAP_SPI1_TX_1 // DMA2, Stream 3, Channel 3 (SPI1 sensors TX) +// AVAILABLE // DMA2, Stream 4 +// DMAMAP_TIM1_UP // DMA2, Stream 5, Channel 6 (DSHOT) +#define DMAMAP_SDIO DMAMAP_SDIO_2 // DMA2, Stream 6, Channel 4 +#define DMAMAP_USART6_TX DMAMAP_USART6_TX_2 // DMA2, Stream 7, Channel 5 (PX4IO TX) diff --git a/boards/thepeach/r1/nuttx-config/nsh/defconfig b/boards/thepeach/r1/nuttx-config/nsh/defconfig new file mode 100644 index 0000000000..0d4bb0a5cf --- /dev/null +++ b/boards/thepeach/r1/nuttx-config/nsh/defconfig @@ -0,0 +1,229 @@ +# +# This file is autogenerated: PLEASE DO NOT EDIT IT. +# +# You can use "make menuconfig" to make any modifications to the installed .config file. +# You can then do "make savedefconfig" to generate a new defconfig file that includes your +# modifications. +# +# CONFIG_DISABLE_ENVIRON is not set +# CONFIG_DISABLE_PSEUDOFS_OPERATIONS is not set +# CONFIG_MMCSD_HAVE_CARDDETECT is not set +# CONFIG_MMCSD_HAVE_WRITEPROTECT is not set +# CONFIG_MMCSD_MMCSUPPORT is not set +# CONFIG_MMCSD_SPI is not set +# CONFIG_NSH_DISABLEBG is not set +# CONFIG_NSH_DISABLESCRIPT is not set +# CONFIG_NSH_DISABLE_DF is not set +# CONFIG_NSH_DISABLE_EXEC is not set +# CONFIG_NSH_DISABLE_EXIT is not set +# CONFIG_NSH_DISABLE_GET is not set +# CONFIG_NSH_DISABLE_ITEF is not set +# CONFIG_NSH_DISABLE_LOOPS is not set +# CONFIG_NSH_DISABLE_MKFATFS is not set +# CONFIG_NSH_DISABLE_SEMICOLON is not set +# CONFIG_NSH_DISABLE_TIME is not set +# CONFIG_STM32_CCMEXCLUDE is not set +CONFIG_ARCH="arm" +CONFIG_ARCH_BOARD_CUSTOM=y +CONFIG_ARCH_BOARD_CUSTOM_DIR="../../../../boards/thepeach/r1/nuttx-config" +CONFIG_ARCH_BOARD_CUSTOM_DIR_RELPATH=y +CONFIG_ARCH_BOARD_CUSTOM_NAME="px4" +CONFIG_ARCH_CHIP="stm32" +CONFIG_ARCH_CHIP_STM32=y +CONFIG_ARCH_CHIP_STM32F427V=y +CONFIG_ARCH_INTERRUPTSTACK=512 +CONFIG_ARCH_STACKDUMP=y +CONFIG_ARMV7M_MEMCPY=y +CONFIG_ARMV7M_USEBASEPRI=y +CONFIG_ARM_MPU_EARLY_RESET=y +CONFIG_BOARDCTL_RESET=y +CONFIG_BOARD_CRASHDUMP=y +CONFIG_BOARD_LOOPSPERMSEC=16717 +CONFIG_BOARD_RESET_ON_ASSERT=2 +CONFIG_BUILTIN=y +CONFIG_C99_BOOL8=y +CONFIG_CDCACM=y +CONFIG_CDCACM_IFLOWCONTROL=y +CONFIG_CDCACM_PRODUCTID=0x0002 +CONFIG_CDCACM_PRODUCTSTR="FCC-R1" +CONFIG_CDCACM_RXBUFSIZE=600 +CONFIG_CDCACM_TXBUFSIZE=2000 +CONFIG_CDCACM_VENDORID=0x35a7 +CONFIG_CDCACM_VENDORSTR="ThePeach" +CONFIG_DEBUG_FULLOPT=y +CONFIG_DEBUG_HARDFAULT_ALERT=y +CONFIG_DEBUG_SYMBOLS=y +CONFIG_DEFAULT_SMALL=y +CONFIG_DEV_FIFO_SIZE=0 +CONFIG_DEV_PIPE_MAXSIZE=1024 +CONFIG_DEV_PIPE_SIZE=70 +CONFIG_DISABLE_MQUEUE=y +CONFIG_EXAMPLES_CALIB_UDELAY=y +CONFIG_FAT_DMAMEMORY=y +CONFIG_FAT_LCNAMES=y +CONFIG_FAT_LFN=y +CONFIG_FAT_LFN_ALIAS_HASH=y +CONFIG_FDCLONE_STDIO=y +CONFIG_FS_BINFS=y +CONFIG_FS_CROMFS=y +CONFIG_FS_FAT=y +CONFIG_FS_FATTIME=y +CONFIG_FS_PROCFS=y +CONFIG_FS_PROCFS_INCLUDE_PROGMEM=y +CONFIG_FS_PROCFS_REGISTER=y +CONFIG_FS_ROMFS=y +CONFIG_GRAN=y +CONFIG_GRAN_INTR=y +CONFIG_HAVE_CXX=y +CONFIG_HAVE_CXXINITIALIZE=y +CONFIG_I2C=y +CONFIG_I2C_RESET=y +CONFIG_IDLETHREAD_STACKSIZE=750 +CONFIG_LIBC_LONG_LONG=y +CONFIG_LIBC_STRERROR=y +CONFIG_MEMSET_64BIT=y +CONFIG_MEMSET_OPTSPEED=y +CONFIG_MMCSD=y +CONFIG_MMCSD_SDIO=y +CONFIG_MMCSD_SDIOWAIT_WRCOMPLETE=y +CONFIG_MM_REGIONS=2 +CONFIG_MTD=y +CONFIG_MTD_BYTE_WRITE=y +CONFIG_MTD_PARTITION=y +CONFIG_MTD_RAMTRON=y +CONFIG_NAME_MAX=40 +CONFIG_NSH_ARCHINIT=y +CONFIG_NSH_ARGCAT=y +CONFIG_NSH_BUILTIN_APPS=y +CONFIG_NSH_CMDPARMS=y +CONFIG_NSH_CROMFSETC=y +CONFIG_NSH_DISABLE_IFCONFIG=y +CONFIG_NSH_DISABLE_IFUPDOWN=y +CONFIG_NSH_DISABLE_TELNETD=y +CONFIG_NSH_LINELEN=128 +CONFIG_NSH_MAXARGUMENTS=15 +CONFIG_NSH_NESTDEPTH=8 +CONFIG_NSH_QUOTE=y +CONFIG_NSH_ROMFSETC=y +CONFIG_NSH_ROMFSSECTSIZE=128 +CONFIG_NSH_STRERROR=y +CONFIG_NSH_VARS=y +CONFIG_PIPES=y +CONFIG_PREALLOC_TIMERS=50 +CONFIG_PRIORITY_INHERITANCE=y +CONFIG_PTHREAD_MUTEX_ROBUST=y +CONFIG_PTHREAD_STACK_MIN=512 +CONFIG_RAMTRON_SETSPEED=y +CONFIG_RAM_SIZE=262144 +CONFIG_RAM_START=0x20000000 +CONFIG_RAW_BINARY=y +CONFIG_RTC_DATETIME=y +CONFIG_SCHED_ATEXIT=y +CONFIG_SCHED_HPWORK=y +CONFIG_SCHED_HPWORKPRIORITY=249 +CONFIG_SCHED_HPWORKSTACKSIZE=1280 +CONFIG_SCHED_INSTRUMENTATION=y +CONFIG_SCHED_INSTRUMENTATION_EXTERNAL=y +CONFIG_SCHED_LPWORK=y +CONFIG_SCHED_LPWORKPRIORITY=50 +CONFIG_SCHED_LPWORKSTACKSIZE=1632 +CONFIG_SCHED_WAITPID=y +CONFIG_SDCLONE_DISABLE=y +CONFIG_SDIO_BLOCKSETUP=y +CONFIG_SEM_PREALLOCHOLDERS=32 +CONFIG_SERIAL_IFLOWCONTROL_WATERMARKS=y +CONFIG_SERIAL_TERMIOS=y +CONFIG_SIG_DEFAULT=y +CONFIG_SIG_SIGALRM_ACTION=y +CONFIG_SIG_SIGUSR1_ACTION=y +CONFIG_SIG_SIGUSR2_ACTION=y +CONFIG_SIG_SIGWORK=4 +CONFIG_STACK_COLORATION=y +CONFIG_START_DAY=30 +CONFIG_START_MONTH=11 +CONFIG_STDIO_BUFFER_SIZE=32 +CONFIG_STM32_ADC1=y +CONFIG_STM32_BBSRAM=y +CONFIG_STM32_BBSRAM_FILES=5 +CONFIG_STM32_BKPSRAM=y +CONFIG_STM32_CCMDATARAM=y +CONFIG_STM32_DISABLE_IDLE_SLEEP_DURING_DEBUG=y +CONFIG_STM32_DMA1=y +CONFIG_STM32_DMA2=y +CONFIG_STM32_FLASH_CONFIG_I=y +CONFIG_STM32_FLOWCONTROL_BROKEN=y +CONFIG_STM32_I2C1=y +CONFIG_STM32_I2CTIMEOMS=10 +CONFIG_STM32_I2CTIMEOTICKS=10 +CONFIG_STM32_JTAG_SW_ENABLE=y +CONFIG_STM32_OTGFS=y +CONFIG_STM32_PWR=y +CONFIG_STM32_RTC=y +CONFIG_STM32_RTC_HSECLOCK=y +CONFIG_STM32_RTC_MAGIC=0xfacefeee +CONFIG_STM32_RTC_MAGIC_REG=1 +CONFIG_STM32_RTC_MAGIC_TIME_SET=0xfacefeef +CONFIG_STM32_SAVE_CRASHDUMP=y +CONFIG_STM32_SDIO=y +CONFIG_STM32_SDIO_CARD=y +CONFIG_STM32_SERIALBRK_BSDCOMPAT=y +CONFIG_STM32_SERIAL_DISABLE_REORDERING=y +CONFIG_STM32_SPI1=y +CONFIG_STM32_SPI1_DMA=y +CONFIG_STM32_SPI1_DMA_BUFFER=512 +CONFIG_STM32_SPI2=y +CONFIG_STM32_SPI_DMA=y +CONFIG_STM32_SPI_DMATHRESHOLD=8 +CONFIG_STM32_TIM10=y +CONFIG_STM32_TIM11=y +CONFIG_STM32_TIM3=y +CONFIG_STM32_TIM9=y +CONFIG_STM32_UART4=y +CONFIG_STM32_UART7=y +CONFIG_STM32_UART8=y +CONFIG_STM32_USART1=y +CONFIG_STM32_USART2=y +CONFIG_STM32_USART3=y +CONFIG_STM32_USART6=y +CONFIG_STM32_USART_BREAKS=y +CONFIG_STM32_USART_SINGLEWIRE=y +CONFIG_STM32_WWDG=y +CONFIG_SYSTEM_CDCACM=y +CONFIG_SYSTEM_NSH=y +CONFIG_TASK_NAME_SIZE=24 +CONFIG_UART4_BAUD=57600 +CONFIG_UART4_RXBUFSIZE=300 +CONFIG_UART4_RXDMA=y +CONFIG_UART4_TXBUFSIZE=300 +CONFIG_UART7_BAUD=57600 +CONFIG_UART7_RXBUFSIZE=300 +CONFIG_UART7_RXDMA=y +CONFIG_UART7_SERIAL_CONSOLE=y +CONFIG_UART7_TXBUFSIZE=300 +CONFIG_UART8_BAUD=57600 +CONFIG_UART8_RXBUFSIZE=300 +CONFIG_UART8_TXBUFSIZE=300 +CONFIG_USART1_RXBUFSIZE=128 +CONFIG_USART1_TXBUFSIZE=32 +CONFIG_USART2_BAUD=57600 +CONFIG_USART2_IFLOWCONTROL=y +CONFIG_USART2_OFLOWCONTROL=y +CONFIG_USART2_RXBUFSIZE=600 +CONFIG_USART2_RXDMA=y +CONFIG_USART2_TXBUFSIZE=1100 +CONFIG_USART3_BAUD=57600 +CONFIG_USART3_IFLOWCONTROL=y +CONFIG_USART3_OFLOWCONTROL=y +CONFIG_USART3_RXBUFSIZE=300 +CONFIG_USART3_RXDMA=y +CONFIG_USART3_TXBUFSIZE=600 +CONFIG_USART6_BAUD=57600 +CONFIG_USART6_RXBUFSIZE=300 +CONFIG_USART6_RXDMA=y +CONFIG_USART6_TXBUFSIZE=300 +CONFIG_USBDEV=y +CONFIG_USBDEV_BUSPOWERED=y +CONFIG_USBDEV_MAXPOWER=500 +CONFIG_USEC_PER_TICK=1000 +CONFIG_USERMAIN_STACKSIZE=2944 +CONFIG_USER_ENTRYPOINT="nsh_main" diff --git a/boards/thepeach/r1/nuttx-config/scripts/script.ld b/boards/thepeach/r1/nuttx-config/scripts/script.ld new file mode 100644 index 0000000000..6d92733df8 --- /dev/null +++ b/boards/thepeach/r1/nuttx-config/scripts/script.ld @@ -0,0 +1,146 @@ +/**************************************************************************** + * scripts/ld.script + * + * Copyright (C) 2011 Gregory Nutt. All rights reserved. + * Author: Gregory Nutt + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name NuttX nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/* The STM32F427 has 2048Kb of FLASH beginning at address 0x0800:0000 and + * 256Kb of SRAM. SRAM is split up into three blocks: + * + * 1) 112Kb of SRAM beginning at address 0x2000:0000 + * 2) 16Kb of SRAM beginning at address 0x2001:c000 + * 3) 64Kb of SRAM beginning at address 0x2002:0000 + * 4) 64Kb of TCM SRAM beginning at address 0x1000:0000 + * + * When booting from FLASH, FLASH memory is aliased to address 0x0000:0000 + * where the code expects to begin execution by jumping to the entry point in + * the 0x0800:0000 address range. + * + * The first 0x4000 of flash is reserved for the bootloader. + */ + +MEMORY +{ + flash (rx) : ORIGIN = 0x08004000, LENGTH = 2032K + sram (rwx) : ORIGIN = 0x20000000, LENGTH = 192K + ccsram (rwx) : ORIGIN = 0x10000000, LENGTH = 64K +} + +OUTPUT_ARCH(arm) + +ENTRY(__start) /* treat __start as the anchor for dead code stripping */ +EXTERN(_vectors) /* force the vectors to be included in the output */ + +/* + * Ensure that abort() is present in the final object. The exception handling + * code pulled in by libgcc.a requires it (and that code cannot be easily avoided). + */ +EXTERN(abort) +EXTERN(_bootdelay_signature) + +SECTIONS +{ + .text : { + _stext = ABSOLUTE(.); + *(.vectors) + . = ALIGN(32); + /* + This signature provides the bootloader with a way to delay booting + */ + _bootdelay_signature = ABSOLUTE(.); + FILL(0xffecc2925d7d05c5) + . += 8; + *(.text .text.*) + *(.fixup) + *(.gnu.warning) + *(.rodata .rodata.*) + *(.gnu.linkonce.t.*) + *(.got) + *(.gcc_except_table) + *(.gnu.linkonce.r.*) + _etext = ABSOLUTE(.); + + } > flash + + /* + * Init functions (static constructors and the like) + */ + .init_section : { + _sinit = ABSOLUTE(.); + KEEP(*(.init_array .init_array.*)) + _einit = ABSOLUTE(.); + } > flash + + + .ARM.extab : { + *(.ARM.extab*) + } > flash + + __exidx_start = ABSOLUTE(.); + .ARM.exidx : { + *(.ARM.exidx*) + } > flash + __exidx_end = ABSOLUTE(.); + + _eronly = ABSOLUTE(.); + + .data : { + _sdata = ABSOLUTE(.); + *(.data .data.*) + *(.gnu.linkonce.d.*) + CONSTRUCTORS + _edata = ABSOLUTE(.); + } > sram AT > flash + + .bss : { + _sbss = ABSOLUTE(.); + *(.bss .bss.*) + *(.gnu.linkonce.b.*) + *(COMMON) + . = ALIGN(4); + _ebss = ABSOLUTE(.); + } > sram + + /* Stabs debugging sections. */ + .stab 0 : { *(.stab) } + .stabstr 0 : { *(.stabstr) } + .stab.excl 0 : { *(.stab.excl) } + .stab.exclstr 0 : { *(.stab.exclstr) } + .stab.index 0 : { *(.stab.index) } + .stab.indexstr 0 : { *(.stab.indexstr) } + .comment 0 : { *(.comment) } + .debug_abbrev 0 : { *(.debug_abbrev) } + .debug_info 0 : { *(.debug_info) } + .debug_line 0 : { *(.debug_line) } + .debug_pubnames 0 : { *(.debug_pubnames) } + .debug_aranges 0 : { *(.debug_aranges) } +} diff --git a/boards/thepeach/r1/src/CMakeLists.txt b/boards/thepeach/r1/src/CMakeLists.txt new file mode 100644 index 0000000000..a7db4590f0 --- /dev/null +++ b/boards/thepeach/r1/src/CMakeLists.txt @@ -0,0 +1,50 @@ +############################################################################ +# +# Copyright (c) 2015 PX4 Development Team. All rights reserved. +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in +# the documentation and/or other materials provided with the +# distribution. +# 3. Neither the name PX4 nor the names of its contributors may be +# used to endorse or promote products derived from this software +# without specific prior written permission. +# +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS +# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT +# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS +# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE +# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, +# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, +# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS +# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED +# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN +# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +# POSSIBILITY OF SUCH DAMAGE. +# +############################################################################ + +add_library(drivers_board + can.c + i2c.cpp + init.c + led.c + spi.cpp + timer_config.cpp + usb.c +) +target_link_libraries(drivers_board + PRIVATE + arch_spi + drivers__led # drv_led_start + nuttx_arch # sdio + nuttx_drivers # sdio + px4_layer +) diff --git a/boards/thepeach/r1/src/board_config.h b/boards/thepeach/r1/src/board_config.h new file mode 100644 index 0000000000..e82847897b --- /dev/null +++ b/boards/thepeach/r1/src/board_config.h @@ -0,0 +1,182 @@ +/**************************************************************************** + * + * Copyright (c) 2013-2016 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file board_config.h + * + * ThePeach R1 internal definitions + */ + +#pragma once + +/**************************************************************************************************** + * Included Files + ****************************************************************************************************/ + +#include +#include +#include + +/**************************************************************************************************** + * Definitions + ****************************************************************************************************/ +/* Configuration ************************************************************************************/ + +/* PX4IO connection configuration */ +#define BOARD_USES_PX4IO_VERSION 2 +#define PX4IO_SERIAL_DEVICE "/dev/ttyS4" +#define PX4IO_SERIAL_TX_GPIO GPIO_USART6_TX +#define PX4IO_SERIAL_RX_GPIO GPIO_USART6_RX +#define PX4IO_SERIAL_BASE STM32_USART6_BASE /* hardwired on the board */ +#define PX4IO_SERIAL_VECTOR STM32_IRQ_USART6 +#define PX4IO_SERIAL_TX_DMAMAP DMAMAP_USART6_TX +#define PX4IO_SERIAL_RX_DMAMAP DMAMAP_USART6_RX +#define PX4IO_SERIAL_RCC_REG STM32_RCC_APB2ENR +#define PX4IO_SERIAL_RCC_EN RCC_APB2ENR_USART6EN +#define PX4IO_SERIAL_CLOCK STM32_PCLK2_FREQUENCY +#define PX4IO_SERIAL_BITRATE 1500000 /* 1.5Mbps -> max rate for IO */ + + +/* PX4FMU GPIOs ***********************************************************************************/ +/* LEDs */ + +#define GPIO_LED1 (GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTE|GPIO_PIN12) +#define BOARD_OVERLOAD_LED LED_RED + +/* + * ADC channels + * + * These are the channel numbers of the ADCs of the microcontroller that can be used by the Px4 Firmware in the adc driver + */ +#define ADC_CHANNELS (1 << 2) | (1 << 3) | (1 << 4) | (1 << 13) | (1 << 14) | (1 << 15) + +// ADC defines to be used in sensors.cpp to read from a particular channel +#define ADC_BATTERY_VOLTAGE_CHANNEL 2 +#define ADC_BATTERY_CURRENT_CHANNEL 3 +#define ADC_5V_RAIL_SENSE 4 +#define ADC_AIRSPEED_VOLTAGE_CHANNEL 15 + +/* Power supply control and monitoring GPIOs */ +// Signal is not connected +#define GPIO_VDD_5V_PERIPH_EN (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN8) +#define GPIO_VDD_BRICK_VALID (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTB|GPIO_PIN5) +#define GPIO_VDD_3V3_SENSORS_EN (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3) +#define GPIO_VDD_5V_PERIPH_OC (GPIO_INPUT|GPIO_PULLUP|GPIO_PORTE|GPIO_PIN15) + +/* Tone alarm output */ +#define TONE_ALARM_TIMER 2 /* timer 2 */ +#define TONE_ALARM_CHANNEL 1 /* channel 1 */ +#define GPIO_TONE_ALARM_IDLE (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_2MHz|GPIO_OUTPUT_CLEAR|GPIO_PORTA|GPIO_PIN15) +#define GPIO_TONE_ALARM (GPIO_ALT|GPIO_AF1|GPIO_SPEED_2MHz|GPIO_PUSHPULL|GPIO_PORTA|GPIO_PIN15) + +/* PWM + */ +#define DIRECT_PWM_OUTPUT_CHANNELS 6 + +/* USB OTG FS + * + * PA9 OTG_FS_VBUS VBUS sensing (also connected to the green LED) + */ +#define GPIO_OTGFS_VBUS (GPIO_INPUT|GPIO_FLOAT|GPIO_SPEED_100MHz|GPIO_OPENDRAIN|GPIO_PORTA|GPIO_PIN9) + +/* High-resolution timer */ +#define HRT_TIMER 8 /* use timer8 for the HRT */ +#define HRT_TIMER_CHANNEL 1 /* use capture/compare channel */ + +/* PWM input driver. Use FMU AUX5 pins attached to timer4 channel 2 */ +#define PWMIN_TIMER 4 +#define PWMIN_TIMER_CHANNEL 2 +#define GPIO_PWM_IN GPIO_TIM4_CH2IN_2 + +/* By Providing BOARD_ADC_USB_CONNECTED this board support the ADC + * system_power interface, and therefore provides the true logic + * GPIO BOARD_ADC_xxxx macros. + */ +#define BOARD_ADC_USB_CONNECTED (px4_arch_gpioread(GPIO_OTGFS_VBUS)) +#define BOARD_ADC_BRICK_VALID (!px4_arch_gpioread(GPIO_VDD_BRICK_VALID)) +#define BOARD_ADC_SERVO_VALID (1) +#define BOARD_ADC_PERIPH_5V_OC (!px4_arch_gpioread(GPIO_VDD_5V_PERIPH_OC)) +#define BOARD_ADC_HIPOWER_5V_OC (0) + + +/* This board provides a DMA pool and APIs */ +#define BOARD_DMA_ALLOC_POOL_SIZE 5120 + +/* This board provides the board_on_reset interface */ + +#define BOARD_HAS_ON_RESET 1 + +#define BOARD_HAS_STATIC_MANIFEST 1 + +__BEGIN_DECLS + +/**************************************************************************************************** + * Public Types + ****************************************************************************************************/ + +/**************************************************************************************************** + * Public data + ****************************************************************************************************/ + +#ifndef __ASSEMBLY__ + +/**************************************************************************************************** + * Public Functions + ****************************************************************************************************/ + +extern void board_peripheral_reset(int ms); + +/**************************************************************************************************** + * Name: stm32_usbinitialize + * + * Description: + * Called to configure USB IO. + * + ****************************************************************************************************/ + +extern void stm32_usbinitialize(void); + +/**************************************************************************************************** + * Name: stm32_spiinitialize + * + * Description: + * Called to configure SPI chip select GPIO pins for the PX4FMU board. + * + ****************************************************************************************************/ + +extern void stm32_spiinitialize(void); + +#include + +#endif /* __ASSEMBLY__ */ +__END_DECLS diff --git a/boards/thepeach/r1/src/can.c b/boards/thepeach/r1/src/can.c new file mode 100644 index 0000000000..5a32d62832 --- /dev/null +++ b/boards/thepeach/r1/src/can.c @@ -0,0 +1,130 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file can.c + * + * Board-specific CAN functions. + */ + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include + +#include +#include + +#include +#include + +#include "chip.h" +#include "arm_arch.h" + +#include "stm32.h" +#include "stm32_can.h" +#include "board_config.h" + +#ifdef CONFIG_CAN + +/************************************************************************************ + * Pre-processor Definitions + ************************************************************************************/ +/* Configuration ********************************************************************/ + +#if defined(CONFIG_STM32_CAN1) && defined(CONFIG_STM32_CAN2) +# warning "Both CAN1 and CAN2 are enabled. Assuming only CAN1." +# undef CONFIG_STM32_CAN2 +#endif + +#ifdef CONFIG_STM32_CAN1 +# define CAN_PORT 1 +#else +# define CAN_PORT 2 +#endif + +/************************************************************************************ + * Private Functions + ************************************************************************************/ + +/************************************************************************************ + * Public Functions + ************************************************************************************/ +int can_devinit(void); + +/************************************************************************************ + * Name: can_devinit + * + * Description: + * All STM32 architectures must provide the following interface to work with + * examples/can. + * + ************************************************************************************/ + +int can_devinit(void) +{ + static bool initialized = false; + struct can_dev_s *can; + int ret; + + /* Check if we have already initialized */ + + if (!initialized) { + /* Call stm32_caninitialize() to get an instance of the CAN interface */ + + can = stm32_caninitialize(CAN_PORT); + + if (can == NULL) { + canerr("ERROR: Failed to get CAN interface\n"); + return -ENODEV; + } + + /* Register the CAN driver at "/dev/can0" */ + + ret = can_register("/dev/can0", can); + + if (ret < 0) { + canerr("ERROR: can_register failed: %d\n", ret); + return ret; + } + + /* Now we are initialized */ + + initialized = true; + } + + return OK; +} + +#endif diff --git a/boards/thepeach/r1/src/i2c.cpp b/boards/thepeach/r1/src/i2c.cpp new file mode 100644 index 0000000000..e9f26f9a9e --- /dev/null +++ b/boards/thepeach/r1/src/i2c.cpp @@ -0,0 +1,38 @@ +/**************************************************************************** + * + * Copyright (C) 2020 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include + +constexpr px4_i2c_bus_t px4_i2c_buses[I2C_BUS_MAX_BUS_ITEMS] = { + initI2CBusExternal(1), +}; diff --git a/boards/thepeach/r1/src/init.c b/boards/thepeach/r1/src/init.c new file mode 100644 index 0000000000..107312832b --- /dev/null +++ b/boards/thepeach/r1/src/init.c @@ -0,0 +1,318 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file init.c + * + * PX4FMU-specific early startup code. This file implements the + * board_app_initialize() function that is called early by nsh during startup. + * + * Code here is run before the rcS script is invoked; it should start required + * subsystems and perform board-specific initialization. + */ + +/**************************************************************************** + * Included Files + ****************************************************************************/ + +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include "board_config.h" +#include + +#include + +#include +#include + +#include + +#include +#include +#include + +/**************************************************************************** + * Pre-Processor Definitions + ****************************************************************************/ + +/* + * Ideally we'd be able to get these from arm_internal.h, + * but since we want to be able to disable the NuttX use + * of leds for system indication at will and there is no + * separate switch, we need to build independent of the + * CONFIG_ARCH_LEDS configuration switch. + */ +__BEGIN_DECLS +extern void led_init(void); +extern void led_on(int led); +extern void led_off(int led); +__END_DECLS + +/**************************************************************************** + * Protected Functions + ****************************************************************************/ +/**************************************************************************** + * Public Functions + ****************************************************************************/ +/************************************************************************************ + * Name: board_on_reset + * + * Description: + * Optionally provided function called on entry to board_system_reset + * It should perform any house keeping prior to the rest. + * + * status - 1 if resetting to boot loader + * 0 if just resetting + * + ************************************************************************************/ +__EXPORT void board_on_reset(int status) +{ + for (int i = 0; i < DIRECT_PWM_OUTPUT_CHANNELS; ++i) { + px4_arch_configgpio(io_timer_channel_get_gpio_output(i)); + } + + /** + * On resets invoked from system (not boot) insure we establish a low + * output state (discharge the pins) on PWM pins before they become inputs. + */ + + if (status >= 0) { + up_mdelay(400); + } +} + +/************************************************************************************ + * Name: board_peripheral_reset + * + * Description: + * + ************************************************************************************/ +__EXPORT void board_peripheral_reset(int ms) +{ + /* set the peripheral rails off */ + stm32_configgpio(GPIO_VDD_5V_PERIPH_EN); + stm32_gpiowrite(GPIO_VDD_5V_PERIPH_EN, 1); + + /* wait for the peripheral rail to reach GND */ + usleep(ms * 1000); + syslog(LOG_DEBUG, "reset done, %d ms\n", ms); + + /* re-enable power */ + + /* switch the peripheral rail back on */ + stm32_gpiowrite(GPIO_VDD_5V_PERIPH_EN, 0); +} + +/************************************************************************************ + * Name: stm32_boardinitialize + * + * Description: + * All STM32 architectures must provide the following entry point. This entry point + * is called early in the intitialization -- after all memory has been configured + * and mapped but before any devices have been initialized. + * + ************************************************************************************/ + +__EXPORT void +stm32_boardinitialize(void) +{ + // Reset all PWM to Low outputs. + + board_on_reset(-1); + + /* configure LEDs */ + + board_autoled_initialize(); + + /* configure ADC pins */ + + px4_arch_configgpio(GPIO_ADC1_IN2); /* BATT_VOLTAGE_SENS */ + px4_arch_configgpio(GPIO_ADC1_IN3); /* BATT_CURRENT_SENS */ + px4_arch_configgpio(GPIO_ADC1_IN4); /* VDD_5V_SENS */ + px4_arch_configgpio(GPIO_ADC1_IN13); /* FMU_AUX_ADC_1 */ + px4_arch_configgpio(GPIO_ADC1_IN14); /* FMU_AUX_ADC_2 */ + px4_arch_configgpio(GPIO_ADC1_IN15); /* PRESSURE_SENS */ + + /* configure power supply control/sense pins */ + px4_arch_configgpio(GPIO_VDD_5V_PERIPH_EN); + px4_arch_configgpio(GPIO_VDD_3V3_SENSORS_EN); + px4_arch_configgpio(GPIO_VDD_BRICK_VALID); + px4_arch_configgpio(GPIO_VDD_5V_PERIPH_OC); + + /* configure CAN interface */ + + stm32_configgpio(GPIO_CAN1_RX); + stm32_configgpio(GPIO_CAN1_TX); + + /* configure SPI interfaces */ + + stm32_spiinitialize(); + + /* configure USB interface */ + + stm32_usbinitialize(); + +} + +/**************************************************************************** + * Name: board_app_initialize + * + * Description: + * Perform application specific initialization. This function is never + * called directly from application code, but only indirectly via the + * (non-standard) boardctl() interface using the command BOARDIOC_INIT. + * + * Input Parameters: + * arg - The boardctl() argument is passed to the board_app_initialize() + * implementation without modification. The argument has no + * meaning to NuttX; the meaning of the argument is a contract + * between the board-specific initalization logic and the the + * matching application logic. The value cold be such things as a + * mode enumeration value, a set of DIP switch switch settings, a + * pointer to configuration data read from a file or serial FLASH, + * or whatever you would like to do with it. Every implementation + * should accept zero/NULL as a default configuration. + * + * Returned Value: + * Zero (OK) is returned on success; a negated errno value is returned on + * any failure to indicate the nature of the failure. + * + ****************************************************************************/ + + +static struct spi_dev_s *spi1; +static struct spi_dev_s *spi2; +static struct sdio_dev_s *sdio; + +__EXPORT int board_app_initialize(uintptr_t arg) +{ + + px4_platform_init(); + + /* configure the DMA allocator */ + + if (board_dma_alloc_init() < 0) { + syslog(LOG_ERR, "DMA alloc FAILED\n"); + } + +#if defined(SERIAL_HAVE_RXDMA) + // set up the serial DMA polling at 1ms intervals for received bytes that have not triggered a DMA event. + static struct hrt_call serial_dma_call; + hrt_call_every(&serial_dma_call, 1000, 1000, (hrt_callout)stm32_serial_dma_poll, NULL); +#endif + + /* initial LED state */ + drv_led_start(); + led_off(LED_AMBER); + + if (board_hardfault_init(2, true) != 0) { + led_on(LED_AMBER); + } + + /* Configure SPI-based devices */ + + spi1 = px4_spibus_initialize(1); + + if (!spi1) { + syslog(LOG_ERR, "[boot] FAILED to initialize SPI port 1\n"); + led_on(LED_AMBER); + } + + /* Default SPI1 to 1MHz and de-assert the known chip selects. */ + SPI_SETFREQUENCY(spi1, 10000000); + SPI_SETBITS(spi1, 8); + SPI_SETMODE(spi1, SPIDEV_MODE3); + up_udelay(20); + + /* Get the SPI port for the FRAM */ + + spi2 = px4_spibus_initialize(2); + + if (!spi2) { + syslog(LOG_ERR, "[boot] FAILED to initialize SPI port 2\n"); + led_on(LED_AMBER); + } + + /* Default SPI2 to 37.5 MHz (40 MHz rounded to nearest valid divider, F4 max) + * and de-assert the known chip selects. */ + + // XXX start with 10.4 MHz in FRAM usage and go up to 37.5 once validated + SPI_SETFREQUENCY(spi2, 12 * 1000 * 1000); + SPI_SETBITS(spi2, 8); + SPI_SETMODE(spi2, SPIDEV_MODE3); + SPI_SELECT(spi2, SPIDEV_FLASH(0), false); + + +#ifdef CONFIG_MMCSD + /* First, get an instance of the SDIO interface */ + sdio = sdio_initialize(CONFIG_NSH_MMCSDSLOTNO); + + if (!sdio) { + syslog(LOG_ERR, "[boot] Failed to initialize SDIO slot %d\n", CONFIG_NSH_MMCSDSLOTNO); + led_on(LED_AMBER); + } + + /* Now bind the SDIO interface to the MMC/SD driver */ + int ret = mmcsd_slotinitialize(CONFIG_NSH_MMCSDMINOR, sdio); + + if (ret != OK) { + syslog(LOG_ERR, "[boot] Failed to bind SDIO to the MMC/SD driver: %d\n", ret); + led_on(LED_AMBER); + } + + /* Then let's guess and say that there is a card in the slot. There is no card detect GPIO. */ + sdio_mediachange(sdio, true); + +#endif + + /* Configure the HW based on the manifest */ + px4_platform_configure(); + + return OK; +} diff --git a/boards/thepeach/r1/src/led.c b/boards/thepeach/r1/src/led.c new file mode 100644 index 0000000000..8a70a4cb29 --- /dev/null +++ b/boards/thepeach/r1/src/led.c @@ -0,0 +1,96 @@ +/**************************************************************************** + * + * Copyright (c) 2013 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file led.c + * + * LED backend. + */ + +#include + +#include + +#include "stm32.h" +#include + +#include "board_config.h" + +/* + * Ideally we'd be able to get these from arm_internal.h, + * but since we want to be able to disable the NuttX use + * of leds for system indication at will and there is no + * separate switch, we need to build independent of the + * CONFIG_ARCH_LEDS configuration switch. + */ +__BEGIN_DECLS +extern void led_init(void); +extern void led_on(int led); +extern void led_off(int led); +extern void led_toggle(int led); +__END_DECLS + +__EXPORT void led_init() +{ + /* Configure LED1 GPIO for output */ + + px4_arch_configgpio(GPIO_LED1); +} + +__EXPORT void led_on(int led) +{ + if (led == 1) { + /* Pull down to switch on */ + px4_arch_gpiowrite(GPIO_LED1, false); + } +} + +__EXPORT void led_off(int led) +{ + if (led == 1) { + /* Pull up to switch off */ + px4_arch_gpiowrite(GPIO_LED1, true); + } +} + +__EXPORT void led_toggle(int led) +{ + if (led == 1) { + if (px4_arch_gpioread(GPIO_LED1)) { + px4_arch_gpiowrite(GPIO_LED1, false); + + } else { + px4_arch_gpiowrite(GPIO_LED1, true); + } + } +} diff --git a/boards/thepeach/r1/src/spi.cpp b/boards/thepeach/r1/src/spi.cpp new file mode 100644 index 0000000000..77d0c37214 --- /dev/null +++ b/boards/thepeach/r1/src/spi.cpp @@ -0,0 +1,49 @@ +/**************************************************************************** + * + * Copyright (C) 2020 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include +#include +#include + +constexpr px4_spi_bus_t px4_spi_buses[SPI_BUS_MAX_BUS_ITEMS] = { + initSPIBus(SPI::Bus::SPI1, { + initSPIDevice(DRV_IMU_DEVTYPE_ICM20602, SPI::CS{GPIO::PortC, GPIO::Pin15}, SPI::DRDY{GPIO::PortC, GPIO::Pin14}), + initSPIDevice(DRV_BARO_DEVTYPE_MS5611, SPI::CS{GPIO::PortD, GPIO::Pin7}), + initSPIDevice(DRV_IMU_DEVTYPE_MPU9250, SPI::CS{GPIO::PortC, GPIO::Pin2}, SPI::DRDY{GPIO::PortD, GPIO::Pin15}), + }), + initSPIBus(SPI::Bus::SPI2, { + initSPIDevice(SPIDEV_FLASH(0), SPI::CS{GPIO::PortD, GPIO::Pin10}), + }), +}; + +static constexpr bool unused = validateSPIConfig(px4_spi_buses); diff --git a/boards/thepeach/r1/src/timer_config.cpp b/boards/thepeach/r1/src/timer_config.cpp new file mode 100644 index 0000000000..7bf538a032 --- /dev/null +++ b/boards/thepeach/r1/src/timer_config.cpp @@ -0,0 +1,51 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +#include + +constexpr io_timers_t io_timers[MAX_IO_TIMERS] = { + initIOTimer(Timer::Timer1), + initIOTimer(Timer::Timer4), +}; + +constexpr timer_io_channels_t timer_io_channels[MAX_TIMER_IO_CHANNELS] = { + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel4}, {GPIO::PortE, GPIO::Pin14}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel3}, {GPIO::PortE, GPIO::Pin13}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel2}, {GPIO::PortE, GPIO::Pin11}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer1, Timer::Channel1}, {GPIO::PortE, GPIO::Pin9}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer4, Timer::Channel2}, {GPIO::PortD, GPIO::Pin13}), + initIOTimerChannelOutputClear(io_timers, {Timer::Timer4, Timer::Channel3}, {GPIO::PortD, GPIO::Pin14}), +}; + +constexpr io_timers_channel_mapping_t io_timers_channel_mapping = + initIOTimerChannelMapping(io_timers, timer_io_channels); diff --git a/boards/thepeach/r1/src/usb.c b/boards/thepeach/r1/src/usb.c new file mode 100644 index 0000000000..6fbea86a0b --- /dev/null +++ b/boards/thepeach/r1/src/usb.c @@ -0,0 +1,108 @@ +/**************************************************************************** + * + * Copyright (C) 2012 PX4 Development Team. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * 3. Neither the name PX4 nor the names of its contributors may be + * used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS + * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE + * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, + * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS + * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED + * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN + * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************/ + +/** + * @file usb.c + * + * Board-specific USB functions. + */ + +/************************************************************************************ + * Included Files + ************************************************************************************/ + +#include + +#include +#include +#include +#include + +#include +#include + +#include +#include + +#include "board_config.h" + +/************************************************************************************ + * Definitions + ************************************************************************************/ + +/************************************************************************************ + * Private Functions + ************************************************************************************/ + +/************************************************************************************ + * Public Functions + ************************************************************************************/ + +/************************************************************************************ + * Name: stm32_usbinitialize + * + * Description: + * Called to setup USB-related GPIO pins for the PX4FMU board. + * + ************************************************************************************/ + +__EXPORT void stm32_usbinitialize(void) +{ + /* The OTG FS has an internal soft pull-up */ + + /* Configure the OTG FS VBUS sensing GPIO, Power On, and Overcurrent GPIOs */ + +#ifdef CONFIG_STM32_OTGFS + px4_arch_configgpio(GPIO_OTGFS_VBUS); + /* XXX We only support device mode + px4_arch_configgpio(GPIO_OTGFS_PWRON); + px4_arch_configgpio(GPIO_OTGFS_OVER); + */ +#endif +} + +/************************************************************************************ + * Name: stm32_usbsuspend + * + * Description: + * Board logic must provide the stm32_usbsuspend logic if the USBDEV driver is + * used. This function is called whenever the USB enters or leaves suspend mode. + * This is an opportunity for the board logic to shutdown clocks, power, etc. + * while the USB is suspended. + * + ************************************************************************************/ + +__EXPORT void stm32_usbsuspend(FAR struct usbdev_s *dev, bool resume) +{ + //ulldbg("resume: %d\n", resume); +}